National Instruments NI R Series Manuel utilisateur

PCIe-7857

GETTING STARTED GUIDE

NI PCIe-7857

R Series Digital I/O Module for PCI Express, 8 AI, 8 AO, 48 DIO,

1 MS/s AI, 512 MB DRAM, Kintex-7 160T FPGA

This document describes how to begin using the PCIe-7857.

Safety Guidelines

Caution Observe all instructions and cautions in the user documentation. Using

the model in a manner not specified can damage the model and compromise the

built-in safety protection. Return damaged models to NI for repair.

EMC Guidelines

This product was tested and complies with the regulatory requirements and limits for

electromagnetic compatibility (EMC) stated in the product specifications. These requirements

and limits provide reasonable protection against harmful interference when the product is

operated in the intended operational electromagnetic environment.

This product is intended for use in industrial locations. However, harmful interference may

occur in some installations, when the product is connected to a peripheral device or test object,

or if the product is used in residential or commercial areas. To minimize interference with

radio and television reception and prevent unacceptable performance degradation, install and

use this product in strict accordance with the instructions in the product documentation.

Furthermore, any changes or modifications to the product not expressly approved by NI could

void your authority to operate it under your local regulatory rules.

Notice Operate this product only with shielded cables and accessories.

Notice The length of all I/O cables must be no longer than 3 m (10 ft).

Preparing the Environment

Ensure that the environment in which you are using the NI PCIe-7857 meets the following

specifications.

Note Refer to the device specifications on ni.com/manuals for complete

specifications.

Storage Environment

Temperature

Operating10 °C to 55 °C

Storage -20 °C to 70 °C

Humidity

Operating 10% RH to 90% RH, noncondensing

Storage 5% RH to 95% RH, noncondensing

Pollution Degree 2

Maximum altitude 2,000 m (at 25 °C ambient temperature)

1For PCI Express adapter cards without integrated air movers, NI defines the local operational

ambient environment to be 25 mm (1 in.) upstream of the leading edge of the card with system

airflow of at least 0.4 m/s (80 LFM) for half length cards and 0.6 m/s (120 LFM) for three-quarter

length cards. For more information about the local operational ambient environment definition for

PCI Express adapter cards, visit ni.com/info and enter the Info Code pcielocalambient.

2| ni.com | NI PCIe-7857 Getting Started Guide

Unpacking the Kit

Notice To prevent electrostatic discharge (ESD) from damaging the device, ground

yourself using a grounding strap or by holding a grounded object, such as your

computer chassis.

1. Touch the antistatic package to a metal part of the computer chassis.

2. Remove the device from the package and inspect the device for loose components or any

other sign of damage.

Notice Never touch the exposed pins of connectors.

Note Do not install a device if it appears damaged in any way.

3. Unpack any other items and documentation from the kit.

Store the device in the antistatic package when the device is not in use.

Verifying the Kit Contents

Verify that the following items are included in the PCIe-7857 kit.

Figure 1. PCIe-7857 Kit Contents

1. Hardware

2. NI-RIO Media

3. Getting Started Guide

Installing Software on the Host Computer

Before using the PCIe-7857, you must install the following application software and device

drivers on the host computer.

1. LabVIEW 2018 SP1 or later

2. LabVIEW FPGA Module 2018 or later

3. NI R Series Multifunction RIO Device Drivers January 2019 or later

NI PCIe-7857 Getting Started Guide | © National Instruments | 3

Visit ni.com/info and enter the Info Code softwareversion for minimum software support

information.

Installing the PCIe-7857

1. Power off and unplug the computer.

2. Access the computer system expansion slots. This step might require you to remove one

or more access panels on the computer case.

3. Locate a compatible slot and remove the corresponding slot cover on the computer back

panel.

4. Touch any metal part of the computer to discharge any static electricity.

5. Insert the PCIe-7857 into the applicable PCI Express system slot. Gently rock the

PCIe-7857 into place. Do not force the device into place.

You cannot install PCI Express devices in PCI slots. PCI Express devices support up-

plugging into a PCI Express slot of higher lane width. For more information, refer to

ni.com/pciexpress.

Figure 2. Installing a PCI Express Device

1. PCI Express Device

2. PCI Express System Slot

3. PC with PCI Express Slot

6. Secure the module mounting bracket to the computer back panel rail.

7. Replace any access panels on the computer case.

8. Plug in and power on your computer.

9. If applicable, install accessories and/or terminal blocks as described in the installation

guides.

10. Attach sensors and signal lines to the device, terminal block, or accessory terminals.

4| ni.com | NI PCIe-7857 Getting Started Guide

Verifying Hardware Installation

You can verify that the system recognizes the PCIe-7857 by using Measurement &

Automation Explorer (MAX).

1. Launch MAX by navigating to Start»All Programs»National Instruments»MAX or by

clicking the MAX desktop icon.

2. Expand Devices and Interfaces.

3. Verify that the device appears under Devices and Interfaces.

If the device does not appear, press <F5> to refresh the view in MAX. If the device does

not appear after refreshing the view, visit ni.com/support for troubleshooting information.

Pinout

DIO30

GND

DIO28

GND

DIO26

GND

DIO24

GND

DIO22

GND

DIO20

GND

DIO18

GND

DIO16

GND

DIO14

GND

DIO12

GND

DIO10

GND

DIO8

GND

DIO6

GND

DIO4

GND

DIO2

GND

DIO0

GND

EXTCLKIN

GND

DIO31

DIO29

GND

DIO25

GND

DIO23

GND

DIO27

GND

DIO21

GND

DIO19

GND

DIO17

GND

DIO15

GND

DIO13

GND

DIO11

GND

DIO9

GND

DIO7

GND

DIO5

GND

DIO3

GND

DIO1

GND

68 34

67 33

66 32

65 31

64 30

63 29

62 28

61 27

60 26

59 25

58 24

57 23

56 22

55 21

54 20

53 19

52 18

51 17

50 16

49 15

48 14

47 13

46 12

45 11

44 10

43 9

42 8

41 7

40 6

39 5

38 4

37 3

36 2

35 1

+5V

DIO0

DIO1

DIO2

DIO3

DIO4

DIO5

DIO6

DIO7

DIO9

DIO11

DIO13

DIO15

AO7

AO6

AO5

AO4

AO3

AO2

AO1

AO0

AISENSE

AI7+

AIGND6

AI6+

AI5+

AIGND4

AI4+

AI3+

AIGND2

AI2+

AI1+

AIGND0

AI0+

+5V

DGND

DIO8

DIO10

DIO12

DIO14

AOGND7

AOGND6

AOGND5

AOGND4

AOGND3

AOGND2

AOGND1

AOGND0

AI7–

AIGND7

AI6–

AI5–

AIGND5

AI4–

AI3–

AIGND3

AI2–

AI1–

AIGND1

AI0–

68 34

67 33

66 32

65 31

64 30

63 29

62 28

61 27

60 26

59 25

58 24

57 23

56 22

55 21

54 20

53 19

52 18

51 17

50 16

49 15

48 14

47 13

46 12

45 11

44 10

43 9

42 8

41 7

40 6

39 5

38 4

37 3

36 2

35 1

CONNECTOR 1

(DIO)

CONNECTOR 0

(MIO)

TERMINAL 34

TERMINAL 68

TERMINAL 1

TERMINAL 35

TERMINAL 34

TERMINAL 68

TERMINAL 1

TERMINAL 35

NI PCIe-7857 Getting Started Guide | © National Instruments | 5

Table 1. PCIe-7857 Signal Descriptions

Signal Description

AI+ Positive analog input signal connection

AI- Negative analog input signal connection

AISENSE Reference connection for NRSE measurements

AIGND Ground reference for the analog input signal

AO Analog output signal connection

AOGND Ground reference for the analog output signal

DIO Digital input/output signal connection

DGND Ground reference for the digital signal

EXTCLKIN External clock input source that can be used for source synchronous

acquisitions. The provided clock source must be stable and glitch-free.

GND Ground connection

Supply (+5 Vout) 5 V power output connection for external devices

NC No connection

The PCIe-7857 is protected from overvoltage and overcurrent conditions.

Note Refer to the device specifications, available at ni.com/manuals for more

information.

6| ni.com | NI PCIe-7857 Getting Started Guide

Where to Go Next

SUPPORT

Services

ni.com/services

NI Community

ni.com/community

Software Support

ni.com/info>swsupport

Support

ni.com/support

SOFTWAREHARDWARE

Configuring a Project

NI-RIO Help

Learn LabVIEW Basics

ni.com/gettingstarted

NI R Series Examples

NI Example Finder

NI PCIe-7846 Specifications

ni.com/manuals

NI PCIe-7846 User Manual

ni.com/manuals

Worldwide Support and Services

The NI website is your complete resource for technical support. At ni.com/support, you have

access to everything from troubleshooting and application development self-help resources to

email and phone assistance from NI Application Engineers.

Visit ni.com/services for information about the services NI offers.

Visit ni.com/register to register your NI product. Product registration facilitates technical

support and ensures that you receive important information updates from NI.

NI corporate headquarters is located at 11500 North Mopac Expressway, Austin, Texas,

78759-3504. NI also has offices located around the world. For support in the United States,

create your service request at ni.com/support or dial 1 866 ASK MYNI (275 6964). For

support outside the United States, visit the Worldwide Offices section of ni.com/niglobal to

access the branch office websites, which provide up-to-date contact information.

Information is subject to change without notice. Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for

information on NI trademarks. Other product and company names mentioned herein are trademarks or trade names of their

respective companies. For patents covering NI products/technology, refer to the appropriate location: Help»Patents in your

software, the patents.txt file on your media, or the National Instruments Patent Notice at ni.com/patents. You can find

information about end-user license agreements (EULAs) and third-party legal notices in the readme file for your NI product. Refer

to the Export Compliance Information at ni.com/legal/export-compliance for the NI global trade compliance policy and how

to obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES AS

TO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. U.S.

Government Customers: The data contained in this manual was developed at private expense and is subject to the applicable

limited rights and restricted data rights as set forth in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015.

378052B-01 December 23, 2018

Autres manuels pour NI R Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels National Instruments Système d'E/S

National Instruments

National Instruments 6583R Manuel utilisateur

National Instruments

National Instruments FieldPoint FP-AI-112 Manuel utilisateur

National Instruments

National Instruments PXI-6289 Manuel utilisateur

National Instruments

National Instruments NI-9477 Manuel utilisateur

National Instruments

National Instruments PCIe-784 R Series Manuel utilisateur

National Instruments

National Instruments NI 9226 Manuel utilisateur

National Instruments

National Instruments USB-9213 Manuel utilisateur

National Instruments

National Instruments PXIe-7867R Manuel utilisateur

National Instruments

National Instruments NI 9201 Manuel utilisateur

National Instruments

National Instruments NI USB-6008 Manuel utilisateur

National Instruments

National Instruments USB-TC01 Manuel

National Instruments

National Instruments C Series Manuel

National Instruments

National Instruments R Series Manuel utilisateur

National Instruments

National Instruments REM-11154 Manuel utilisateur

National Instruments

National Instruments R Series Manuel utilisateur

National Instruments

National Instruments NI USB-9219 Manuel utilisateur

National Instruments

National Instruments PXIe-7862R Manuel utilisateur

National Instruments

National Instruments NI 6115/6120 Manuel utilisateur

National Instruments

National Instruments sbRIO-9219 Manuel utilisateur

National Instruments

National Instruments R Series Manuel utilisateur

National Instruments

National Instruments Isolated Analog Input Modules SCC-AI01 Manuel utilisateur

National Instruments

National Instruments NI USB-7845R Manuel utilisateur

National Instruments

National Instruments FIELDPOINT FP-DO-403 Manuel utilisateur

National Instruments

National Instruments NI 9225 Manuel utilisateur

Manuels Système d'E/S populaires d'autres marques

WAGO

WAGO 750-344 Manuel utilisateur

Teknim

Teknim TWM-1887 Mode d’emploi

Intelligent Appliance

Intelligent Appliance IA-2662-E Manuel utilisateur

BERGHOF

BERGHOF ECC DIO 16/16 Mode d’emploi

Advantech

Advantech PCM-27J3AU Manuel d'installation et d'exploitation

Festo

Festo CP-E08-M12-CL Manuel utilisateur

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manuel utilisateur

Hitachi

Hitachi HX-RIO3 Series Manuel utilisateur

NUUO

NUUO SCB-A08 Manuel utilisateur

M-system

M-system R3Y-RS8 Manuel utilisateur

jablotron

jablotron JB-110N Manuel utilisateur

Omron

Omron SYSMAC C200H Manuel utilisateur

DOLD

DOLD SAFEMASTER M Manuel utilisateur

ABB

ABB OPT-MF-001 Manuel utilisateur

Omron

Omron SYSMAC C2000H Manuel utilisateur

Helmholz

Helmholz TB20 Manuel utilisateur

ICP DAS USA

ICP DAS USA tM-AD2 Manuel utilisateur

Automationdirect.com

Automationdirect.com DL305 Manuel utilisateur