National Instruments IC-3173 Manuel utilisateur

USER MANUAL

IC-3173

Industrial Controller with Reconfigurable I/O

This document contains detailed electrical and mechanical information for the National

Instruments IC-3173.

Contents

About the IC-3173.................................................................................................................... 1

Hardware Overview.................................................................................................................. 2

Connector Pinouts............................................................................................................. 3

LED Indicators................................................................................................................15

Using the RESET Button................................................................................................ 18

Replacing the Battery......................................................................................................18

Mounting the IC-3173.............................................................................................................19

Securing the IC-3173 to a Mount....................................................................................22

Clearance Requirements................................................................................................. 24

Software Options.....................................................................................................................25

BIOS Configuration and System Recovery............................................................................ 25

Entering BIOS Setup.......................................................................................................25

BIOS Setup Utility Keyboard Navigation...................................................................... 25

Main Setup Menu............................................................................................................26

Advanced Menu.............................................................................................................. 27

Boot Menu.......................................................................................................................29

Save & Exit Menu...........................................................................................................30

Restoring the Device to Factory Default Condition........................................................31

Where to Go Next................................................................................................................... 31

Resources for LabVIEW Users.......................................................................................31

Resources for Vision Builder AI Users...........................................................................32

About the IC-3173

The IC-3173 is a high-performance, small, fanless embedded computer designed for rugged

industrial applications. The IC-3173 also provides multiple digital input/output (I/O) options

for communicating with external devices.

Hardware Overview

The IC-3173 front panel consists of four Gigabit Ethernet ports with Power over Ethernet

(PoE), one RS-232/RS-485 serial port, one standard Gigabit Ethernet Port, two USB 3.0 ports,

four USB 2.0 ports, and two DisplayPort connectors.

The IC-3173 front panel also includes LEDs for communicating system status and a 44-pin

Digital I/O port. The Digital I/O port offers 8 isolated inputs, 8 isolated outputs, 2 bidirectional

differential I/O (RS-422) or single-ended input lines that can be used with a quadrature

encoder, and 8 bidirectional TTL lines.

2| ni.com | IC-3173 User Manual

Figure 1. IC-3173 Front Panel

POWER

PoE1

PoE2

PoE3

PoE4

DIO

STATUS

USER1

USER FPGA1

ACT/

LINK

10/10 0/

1000

SYS PWR IN

150

W MAX

ISO PWR IN

5-24 V

RESET

9-30 V

IC-3173

Industrial Controller

1. DisplayPort Connectors

2. LED Indicators

3. Power over Ethernet (PoE) LED Indicators

4. Gigabit Ethernet Ports with PoE

5. 44-pin Digital I/O Connector

6. Isolated Power Input Connector

7. Chassis Grounding Screw

8. Reset Button (not pictured)

9. Power Button

10. System Power Connector

11. User-Accessible Battery Compartment (not

pictured)

12. RS-232/RS-485 Serial Port

13. USB 3.0 Ports

14. Primary Gigabit Ethernet Port

15. Retention Mounts for USB 3.0 Ports

16. Retention Mounts for USB 2.0 Ports

17. USB 2.0 Ports

Connector Pinouts

The IC-3173 provides the following connectors.

DisplayPort

Use the DisplayPort connectors to connect one or more monitors to implement a local HMI for

your controller. You can develop a single real-time VI to use for both your user interface and

system logic. For more information, refer to the Using the Embedded UI to Access RT Target

IC-3173 User Manual | © National Instruments | 3

VIs topic in the LabVIEW Help. For up-to-date information about supported NI cables and

accessories, refer to the pricing section of the product page at ni.com.

Use an appropriate adapter cable to connect a DisplayPort connector to a VGA or DVI

connector. The following figure lists the DisplayPort pins and signals.

Figure 2. DisplayPort Connector Pin Locations

19 20

Table 1. DisplayPort Connector Pin Descriptions

Pin Signal Name

1 ML_Lane0(p)

2 GND

3 ML_Lane0(n)

4 ML_Lane1(p)

5 GND

6 ML_Lane1(n)

7 ML_Lane2(p)

8 GND

9 ML_Lane2(n)

10 ML_Lane3(p)

11 GND

12 ML_Lane3(n)

13 CONFIG1

14 CONFIG2

15 AUX CH (p)

16 GND

17 AUX CH (n)

18 Hot Plug Detect

4| ni.com | IC-3173 User Manual

Table 1. DisplayPort Connector Pin Descriptions (Continued)

Pin Signal Name

19 Return

20 DP_PWR

Ethernet Ports

The IC-3173 provides one standard Gigabit Ethernet network port and four Gigabit Ethernet

ports with Power over Ethernet (PoE). The Ethernet ports provide a connection between the

IC-3173, a network, and other Ethernet devices. The IC-3173 automatically detects the speed

of the connection and configures itself accordingly.

If a PoE-capable device is plugged into an Ethernet port with PoE, the IC-3173 automatically

supplies power to the device. When the IC-3173 supplies PoE, the LED that corresponds to the

port illuminates. When you unplug a PoE device, PoE is automatically disabled. You can use

non-PoE Ethernet devices with the PoE-enabled Gigabit Ethernet ports.

A CAT 5e or CAT 6 1000Base-T Ethernet cable is required to achieve 1,000 Mbps (Gigabit)

Ethernet performance. CAT 5 Ethernet cables are not guaranteed to meet the necessary

requirements. While CAT 5 cables may appear to work at 1,000 Mbps, CAT 5 cables can cause

bit errors, resulting in degraded or unreliable network performance.

Figure 3. Ethernet Port Pin Locations

Table 2. Ethernet Port Pin Descriptions

Pin Fast Ethernet (100 Mbps) Gigabit Ethernet

MDI MDI-X

1 TX+ BI_DA+ BI_DB+

2 TX- BI_DA- BI_DB-

3 RX+ BI_DB+ BI_DA+

4 No Connect BI_DC+ BI_DD-

5 No Connect BI_DC- BI_DD-

IC-3173 User Manual | © National Instruments | 5

Table 2. Ethernet Port Pin Descriptions (Continued)

Pin Fast Ethernet (100 Mbps) Gigabit Ethernet

MDI MDI-X

6 RX- BI_DB- BI_DA-

7 No Connect BI_DD+ BI_DC+

8 No Connect BI_DD- BI_DC-

Digital I/O

The 44-pin Digital I/O port on the IC-3173 offers 8 isolated inputs, 8 isolated outputs, 2

bidirectional differential inputs (RS-422) or single-ended input lines that can be used with a

quadrature encoder, and 8 bidirectional TTL lines. The Digital I/O port can be connected to

any appropriate shielded device or connector block using a shielded cable.

NI recommends the following digital I/O cables for the IC-3173.

Cable Part Number

44-pin D-sub male to pigtail cable 156083-03 for 3 meter cable

44-pin D-sub male to 44-position D-sub female cable 156084-03 for 3 meter cable

156084-0R5 for 0.5 meter cable

Refer to the following image and table for pin locations and descriptions.

Figure 4. 44-pin Digital I/O Connector Pin Locations

Table 3. Digital I/O Pin Descriptions

Pin Number Signal Description

1 Diff 0+ Bidirectional RS-422 I/O (positive side), or quadrature encoder

phase A+

2 GND Digital ground reference for TTL and differential I/O

6| ni.com | IC-3173 User Manual

Table 3. Digital I/O Pin Descriptions (Continued)

Pin Number Signal Description

3 TTL 0 Bidirectional TTL I/O

4 TTL 1 Bidirectional TTL I/O

5 GND Digital ground reference for TTL and differential I/O

6 TTL 2 Bidirectional TTL I/O

7 TTL 3 Bidirectional TTL I/O

8 GND Digital ground reference for TTL and differential I/O

9 Diff 1+ Bidirectional RS-422 I/O (positive side), or quadrature encoder

phase B+

10 VISO Isolated power voltage reference output

11 CISO Common ground reference for isolated inputs and outputs

12 Iso Out 0 General purpose isolated input

13 Iso Out 1 General purpose isolated input

14 CISO Common ground reference for isolated inputs and outputs

15 Iso Out 4 General purpose isolated output

16 Diff 0- Bidirectional RS-422 I/O (negative side), or quadrature encoder

phase A-

17 GND Digital ground reference for TTL and differential I/O

18 TTL 4 Bidirectional TTL I/O

19 TTL 5 Bidirectional TTL I/O

20 GND Digital ground reference for TTL and differential I/O

21 TTL 6 Bidirectional TTL I/O

22 TTL 7 Bidirectional TTL I/O

23 GND Digital ground reference for TTL and differential I/O

24 Diff 1- Bidirectional RS-422 I/O

25 VISO Isolated power voltage reference output

26 CISO Common ground reference for isolated inputs and outputs

27 Iso Out 2 General purpose isolated output

28 Iso Out 3 General purpose isolated output

IC-3173 User Manual | © National Instruments | 7

Table 3. Digital I/O Pin Descriptions (Continued)

Pin Number Signal Description

29 CISO Common ground reference for isolated inputs and outputs

30 Iso Out 5 General purpose isolated output

31 Iso In 0 General purpose isolated input

32 iso In 1 General purpose isolated input

33 CISO Common ground reference for isolated inputs and outputs

34 Iso In 2 General purpose isolated input

35 Iso In 3 General purpose isolated input

36 CISO Common ground reference for isolated inputs and outputs

37 Iso In 4 General purpose isolated input

38 Iso In 5 General purpose isolated input

39 CISO Common ground reference for isolated inputs and outputs

40 Iso In 6 General purpose isolated input

41 Iso In 7 General purpose isolated input

42 CISO Common ground reference for isolated inputs and outputs

43 Iso Out 6 General purpose isolated output

44 Iso Out 7 General purpose isolated output

Wiring an Isolated Input

You can wire an isolated input to a sourcing output device.

8| ni.com | IC-3173 User Manual

Caution Do not apply a voltage greater than 30 VDC to the isolated inputs.

Voltage greater than 30 VDC may damage the IC-3173.

Figure 5. Connecting an Isolated Input to a Sourcing Output Device

VREF

CISO

Industrial Controller

Input

Sourcing

Output

Device

Current

Limiter

Power Supply

–

Wiring an Isolated Output

The digital isolated output circuits source current to external loads.

When an inductive load, such as a relay or solenoid, is connected to an output, a large counter-

electromotive force may occur at switching time due to energy stored in the inductive load.

This flyback voltage can damage the outputs and the power supply.

To limit flyback voltages at the inductive load, install a flyback diode across the load. Mount

the flyback diode as close to the load as possible. Use this protection method if you connect

any of the isolated outputs on the IC-3173 to an inductive load.

The following image shows an example of an isolated output wired to an external load with a

flyback diode installed across the load.

IC-3173 User Manual | © National Instruments | 9

Caution Do not draw more than 35 mA from each isolated output when VISO is

5 V. Do not draw more than 80 mA from each isolated output when VISO is 24 V.

Figure 6. Connecting an Isolated Output to an External Load

Digital Output

External Flyback

Diode for

Inductive Loads

VISO

CISO

VCC

Industrial Controller

Load

Overcurrent

Protection Circuit

Connecting to Differential I/O

The IC-3173 accepts differential (RS-422) line driver inputs. Each of the two differential I/O

can be configured as an output. Use shielded cables for all applications. Unshielded cables are

more susceptible to noise and can corrupt signals.

10 | ni.com | IC-3173 User Manual

Autres manuels pour IC-3173

Table des matières

Autres manuels National Instruments Contrôleurs

National Instruments

National Instruments RMC-8354 Manuel utilisateur

National Instruments

National Instruments cRIO-9038 Manuel utilisateur

National Instruments

National Instruments CMS-9068 Instructions de montage

National Instruments

National Instruments PXI-8195 Manuel utilisateur

National Instruments

National Instruments VXIpc 600 Series Manuel utilisateur

National Instruments

National Instruments cRIO-9034 Manuel utilisateur

National Instruments

National Instruments MXI-Express Gen-3 x16 Manuel utilisateur

National Instruments

National Instruments FELDPoint FP-2000 Manuel utilisateur

National Instruments

National Instruments UMI-7774 Manuel utilisateur

National Instruments

National Instruments PXI-8231 Manuel utilisateur

National Instruments

National Instruments sbRIO-9605 Manuel utilisateur

National Instruments

National Instruments cRIO-9037 Manuel utilisateur

National Instruments

National Instruments cRIO-9030 Manuel utilisateur

National Instruments

National Instruments sbRIO-9637 Manuel utilisateur

National Instruments

National Instruments PXI-8115 Manuel utilisateur

National Instruments

National Instruments 73 Series Manuel utilisateur

National Instruments

National Instruments NI PXIe-8840 Manuel utilisateur

National Instruments

National Instruments IC-3120 Manuel utilisateur

National Instruments

National Instruments FieldPoint cFP-2120 Manuel utilisateur

National Instruments

National Instruments CompactRIO cRIO-9025 Manuel utilisateur

National Instruments

National Instruments Compact FieldPoint cFP-21 Series Manuel utilisateur

National Instruments

National Instruments GPIB-ENET Manuel utilisateur

National Instruments

National Instruments Motion Control 7334 Manuel utilisateur

National Instruments

National Instruments PXIe-8861 Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur