National Instruments SbRIO-9860 Manuel utilisateur

sbRIO-9860

Getting Started

2022-07-06

Contents

Purpose. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Connecting the sbRIO-9860. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

sbRIO-9860 Hardware Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Inserting and Removing the NI-XNET Transceiver Cable. . . . . . . . . . . . . . . . . . . . . . . . . . 4

Inserting and Removing the Power Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

NI Services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

ni.com

sbRIO-9860 Getting Started

Purpose

This document describes how to connect to the sbRIO-9860.

Note Before you begin, complete the soware and hardware installation

procedures in your chassis documentation.

Note The guidelines in this document are specific to the sbRIO-9860. The

other components in the system might not meet the same safety ratings.

Refer to the documentation for each component in the system to

determine the safety and EMC ratings for the entire system. Refer to the

sbRIO-9860 Safety, Environmental, and Regulatory Information for

safety and EMC information specific to the sbRIO-9860 module.

Note The sbRIO-9860 must be installed inside a suitable shielded

enclosure prior to use.

Connecting the sbRIO-9860

The sbRIO-9860 has two ports for connecting to transceiver cables (required to

connect to the CAN/LIN bus) and a two-position connector for use with an external

power supply.

For more information about transceiver cables, refer to the Transceiver Cable page

on ni.com.

The sbRIO-9860 requires an external power supply of +9 V to +30 V to power the

transceiver cables. Supply power to the sbRIO-9860 VSUP connector on the module

sbRIO-9860 Getting Started

front panel using the supplied power cable. The exposed lead wires at the end of the

power cable are routed as follows: black wire—COM, red wire—VSUP. The power

cable lead wires may be daisy-chained to the controller power port when the

controller supply voltage is in the appropriate range.

Note Power on VSUP is required for transceiver cable operation.

Note When using more than four transceiver cables with your

CompactRIO chassis, refer to the Transceiver Cable page on ni.com for

mounting guidelines to limit the thermal impact to your CompactRIO

system.

sbRIO-9860 Hardware Overview

The sbRIO-9860 is a two-port C Series board based on the XNET architecture. Users

can choose the physical bus protocol by plugging in the corresponding transceiver

cable. The sbRIO-9860 supports hot-swapping of transceiver cables and can detect

and identify transceiver cable types.

For more information about transceiver cables, refer to the Transceiver Cable page

on ni.com.

Figure 1. sbRIO-9860 Hardware Overview

Ext Pwr

Supply

Required

Controller

COM

Vsup

Pwr Sup

Controller

Port 1

Port 2

Transceiver

Cable

Transceiver

Cable

Inserting and Removing the NI-XNET Transceiver Cable

The NI-XNET Transceiver Cable connects to a host device with an active latching

connector. To connect the NI-XNET Transceiver Cable to a host device, push the

connector assembly into the host receptacle until the internal latch snaps into

position. The latch emits an audible click when engaged. To remove the NI-XNET

ni.com

sbRIO-9860 Getting Started

Transceiver Cable, push the lock ejector forward to disengage the latch and

simultaneously pull the NI-XNET Transceiver Cable, as shown in the following figure.

Figure 2. Inserting and Removing the NI-XNET Transceiver Cable

Inserting and Removing the Power Cable

The sbRIO-9860 connects to the provided power cable with an active latching

connector. To connect the power cable, push the end of the power cable into the

two-position connector until the internal latch snaps into position. The latch emits

an audible click when engaged.

To remove the power cable, push the lock ejector down to disengage the latch and

simultaneously pull the power cable away from the module, as shown in the

following figure.

Figure 3. Removing the Power Cable

NI Services

Visit ni.com/support to find support resources including documentation,

downloads, and troubleshooting and application development self-help such as

tutorials and examples.

Visit ni.com/services to learn about NI service oerings such as calibration options,

repair, and replacement.

Visit ni.com/register to register your NI product. Product registration facilitates

technical support and ensures that you receive important information updates from

NI.

sbRIO-9860 Getting Started

NI corporate headquarters is located at 11500 N Mopac Expwy, Austin, TX,

78759-3504, USA.

ni.com

sbRIO-9860 Getting Started

Table des matières

Autres manuels National Instruments Contrôleurs

National Instruments

National Instruments AT-GPIB/TNT Manuel utilisateur

National Instruments

National Instruments NI PXIe-8135 Manuel utilisateur

National Instruments

National Instruments NI PXI-8104 Manuel utilisateur

National Instruments

National Instruments GPIB Series Manuel utilisateur

National Instruments

National Instruments CompactRIO sbRIO-9603 Instructions de montage

National Instruments

National Instruments NI PXI-8104 Manuel utilisateur

National Instruments

National Instruments PXI-8109 Manuel utilisateur

National Instruments

National Instruments PXI-7358 Manuel utilisateur

National Instruments

National Instruments cRIO-9063 Manuel utilisateur

National Instruments

National Instruments PXI Series Manuel utilisateur

National Instruments

National Instruments NI-488.2 Manuel utilisateur

National Instruments

National Instruments Two-Slot Embedded Controller NI PXI-8183 Manuel utilisateur

National Instruments

National Instruments IC-3120 Manuel utilisateur

National Instruments

National Instruments PXI-8106 Manuel utilisateur

National Instruments

National Instruments GPIB PCI-GPIB Manuel utilisateur

National Instruments

National Instruments sbRIO-9607 Manuel utilisateur

National Instruments

National Instruments IC-3173 Manuel utilisateur

National Instruments

National Instruments Motion Control 7334 Manuel utilisateur

National Instruments

National Instruments IC-3173 Manuel utilisateur

National Instruments

National Instruments myRIO-1950 Manuel utilisateur

National Instruments

National Instruments Fieldpoint CFP-2200 Manuel utilisateur

National Instruments

National Instruments 7330 Manuel utilisateur

National Instruments

National Instruments 7932 Manuel utilisateur

National Instruments

National Instruments cRIO-904 Series Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur

National Instruments sbRIO-9860 Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques