National Instruments NI PXI-2585 Manuel utilisateur

INSTALLATION GUIDE

NI PXI-2585/2586

Connector and Backshell Kit

This document describes how to create and install a cable that connects

high current signals to the NI PXI-2585 or NI PXI-2586 switch module.

Introduction

The connector and backshell kit for the PXI-2585/2586 switch module

contains all of the components necessary to build a cable assembly that is

safe for use with the entire operating range of the PXI-2585/2586 series of

products. Read through this installation guide carefully to ensure that the

cable you build is safe to use with your switch module.

Caution When hazardous voltages (>42.4 Vpk/60 VDC) are present on any solder cup pin,

safety low-voltage (≤42.4 Vpk/60 VDC) cannot be connected to any other solder cup pin.

The PXI-2585/2586 connector and backshell kit contains the following:

• Empty metal backshell

• Solder cup pins (Qty. 22)

• 0.050 in. Allen wrench

• Polyimide tape

You must supply the following items to complete the construction of the

cable:

• Soldering iron

• 16 AWG stranded wire

Caution If your cable assemblywill be used in high-voltage applications (>42.4Vpk/60VDC),

you must use UL style 2464 approved cable.

• Specifications for the module with which the cable will be used

Ρ΅νιϋΠȂ඾ུࢊβȜΐ܄ȃ

NI PXI-2585/2586 Connector and Backshell Kit 2 ni.com

Note The NI PXI-2585/2586 Specifications contains the pinout diagram necessary to

build the cable. Visit ni.com/manuals for the most current specifications for your

PXI-2585/2586 switch module.

Caution You must install this connector and backshell assembly according to local safety

codes and standards and according to the specifications provided by the connector

manufacturer. You are responsible for verifying safety compliance of third-party

connectors and their usage according to the relevant standard(s), including UL and CSA in

North America and IEC and VDE in Europe.

Constructing the Cable

Complete the following steps to construct a cable assembly designed to

meet high-voltage requirements (>42.4 Vpk/60 VDC).

Note If your cable assembly will be used only in low-voltage applications, the use of

UL style 2464 approved insulated cable is unnecessary. Proceed directly to step 2 to

construct a cable assembly for low-voltage applications.

1. Remove 1 in. of outer insulation from the UL style 2464 approved

cable.

2. Strip 0.2 in. (5.1 mm) of insulation from the end of each conductor.

3. Fully insert the stripped portion of each conductor into one of the

solder cup pins provided with the kit. If the conductor has been

inserted correctly, you will be able to see it through the opening in

the pin.

4. Solder each conductor to the pin by heating the conductor through the

opening of the pin. Ensure that the finished solder does not protrude

out of the opening in the pin.

©National Instruments Corporation 3 NI PXI-2585/2586 Connector and Backshell Kit

Figure 1 illustrates the components of your backshell assembly.

Figure 1. Connector and Backshell for the PXI-2585/2586

5. Remove the set screws from the knobs of the jack screws using the

Allen wrench.

6. Loosen the strain-relief bracket until it is fully open.

7. Remove the metal backshell from the plastic connector.

1SetScrews

2 Knobs

3Washers

4 Strain-Relief

5 Metal Backshell

6 Plastic Connector

7JackScrews

NI PXI-2585/2586 Connector and Backshell Kit 4 ni.com

8. Route all the conductors through the backshell as illustrated in

Figure 2.

Figure 2. Backshell with Threaded Wires

9. Refer to the front panel pinout diagram in your module specifications.

Use this diagram to insert the solder cup pins (with conductors

attached) into the connector. Solder cup pins will snap into place when

inserted correctly, as shown in Figure 3.

Note The letters on the backshell connector match the letters on the module. For example,

connector position “A” on your PXI-2585/2586 switch module will mate with the

connector in position “A” on the backshell kit.

Note Take care to insert the pin into the correct connector position. Once the pin is

inserted, it can only be removed from the connector with an extraction tool. Extraction

tools must be purchased separately.

1 16 AWG Stranded Wire

(UL Style 2464 Cable Shown)

2 Solder Cup Pins

©National Instruments Corporation 5 NI PXI-2585/2586 Connector and Backshell Kit

Figure 3. Connector with Inserted Solder Cup Pins

10. Cut 10 in. of polyimide tape from the roll provided. Wrap the tape

around the connector twice near the interface between the conductors

and the connector. The connector should now look like Figure 4.

Caution The polyimide tape must be installed per these instructions or your cable will only

be rated to 42.4 Vpk/60 VDC.

Figure 4. Connector Wrapped with Polyimide Tape

1 Polyimide Tape

NI PXI-2585/2586 Connector and Backshell Kit 6 ni.com

11. Reassemble the connector and backshell. Slide the backshell up the

cable, and tighten the strain-relief.

Note Replace the jack screw shaped like a socket nearest to pin “U” of the connector.

Insert the male jack screw nearest to pin “A” of the connector to ensure proper mating.

Accessories

Table 1. Optional Third-Party Accessories for the NI PXI-2585/2586 Connector and Backshell Kit

Accessory Manufacturer Part Number

Contact insertion tool Positronic 9099

Contact extraction tool Positronic 9081

National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation. Refer to the Terms of Use section on

ni.com/legal for more information about National Instruments trademarks. Other product and company names mentioned herein are

trademarks or trade names of their respective companies. For patents covering National Instruments products, refer to the appropriate location:

Help»Patents in your software, the patents.txt file on your CD, or ni.com/patents.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels National Instruments Unité de contrôle

National Instruments

National Instruments 9871 Manuel utilisateur

National Instruments

National Instruments NI FlexRIO PXIe-7971R Manuel utilisateur

National Instruments

National Instruments SCXI-1581 Manuel utilisateur

National Instruments

National Instruments NI 9214 Manuel utilisateur

National Instruments

National Instruments cRIO-9068 Manuel utilisateur

National Instruments

National Instruments Relay Module SCC-RLY01 Manuel utilisateur

National Instruments

National Instruments NI-9477 Manuel utilisateur

National Instruments

National Instruments 6589 Manuel utilisateur

National Instruments

National Instruments NI 9214 Manuel utilisateur

National Instruments

National Instruments SCC-AI Series Manuel utilisateur

National Instruments

National Instruments Module SCXI-1125 Manuel utilisateur

National Instruments

National Instruments PXI Terminal Block NI TB-2708 Manuel utilisateur

National Instruments

National Instruments NI 9265 Manuel utilisateur

National Instruments

National Instruments PXIe-4339 Manuel utilisateur

National Instruments

National Instruments FlexRIO PXI-79 R Series Manuel utilisateur

National Instruments

National Instruments 9512 C Series Manuel utilisateur

National Instruments

National Instruments FieldPoint FP-DI-301 Manuel utilisateur

National Instruments

National Instruments GPIB-ENET Manuel utilisateur

National Instruments

National Instruments NI USB-9264 Manuel utilisateur

National Instruments

National Instruments SCXI-1100 Manuel utilisateur

National Instruments

National Instruments FP-AI-102 Manuel utilisateur

National Instruments

National Instruments NI FlexRIO Manuel utilisateur

National Instruments

National Instruments PXIe-4353 Manuel

National Instruments

National Instruments NI-9208 Manuel

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur