NAPCO XP-400 Express Series Manuel utilisateur

Usin

Your

XP-400

Security System

$50('

5($'<

6<67(0

=21( 

=21( 

=21( 

=21( 

NAPCO

Oi220a

page 1 Tuesday, September 16, 1997 08:30

www.ealarm.com.my

1Bell / Battery Test

Test your bell or siren by pressing



followed by



This will cause the bell, or siren to sound for 2 seconds and

also initiate a test of the battery .

2Central Station Communication Test

(This test should only be performed on weekends or at a

time designated by your alarm company)

1. Notify Central Station of the impending test.

2. Secure all zones to light Ready Light on your keypad.

3. Enter your user code to Arm the system.

4. Violate your alarm by opening a window / door etc.

5. The siren or bell should sound and the system will send

the alarm signals to the Central Station

6. Enter your user code to silence the bell or sounder.

7. Call Central Station to insure that the alarm signals were

received properly.

Introduction

System Information

Central Station Phone Number: ____________________

Central Station Account Number: ____________________

For Service Call: ____________________

Entry Delay: ____________________

Exit Delay: ____________________

Alarm Time-out: ____________________

Important - Test Your System Weekly !

Table of Contents

Keypad Controls and Indicators ................................ 5

Arming your System (When Leaving) ....................... 6

Bypassing Zones ..................................................... 6

Protecting Yourself While Home ............................... 7

Emergency Keys ....................................................... 8

Disarming the System ............................................... 9

Silencing an Alarm..................................................... 9

Special Functions ..................................................... 10

Programming User Codes ......................................... 11

System Troubles ....................................................... 12

Glossary ................................................................... 15

Oi220a

page 4 Tuesday, September 16, 1997 08:30

www.ealarm.com.my

$50('

5($'<

6<67(0

=21( 

=21( 

=21( 

=21( 

Keypad Controls and Indicators

Ready Light will light when all zones are secure

and system is ready to be Armed.

Zone Lights (1 through 4) will light to indicate

that the corresponding Zone is open, and will

flash to indicate a zone in alarm.

Armed Light will light when system is Armed,

and will flash when system is in Alarm

Key - (Reset) used to clear miss-entered

codes, reset Alarm Memory, etc..

System Light will light and the Keypad

sounder will pulse to indicate that a system trou-

ble is present.

(See System troubles, Page 12)

Key Press to display any present

System troubles. Only available when

System Light is lit.

(See System troubles, Page 12)

Emergency Keys Press

simultaneously to signal

an emergency condition.

Press $+$for

Auxiliary Emergency or

3+3for Police Emer-

gency. (Programmable)

Bypass Key Used to

bypass zones. Press

Bypass and the corre-

sponding zone number,

and then Arm system.

Key Used to enable

special functions and op-

tions. Press and then

the corresponding Spe-

cial Function number Op-

tion (See Special Func-

tions, Page 10)

Numerical Keys 1-9, 0. Used to enter

User Codes, Zone numbers, etc.

NAPCO

Oi220a

page 5 Tuesday, September 16, 1997 08:30

www.ealarm.com.my

Arming Your System When Leaving

1Before armin

your system, make sure the Green Ready li

ht is ON. This indicates that all of your prot-

ective zones are secure. If any zones are open, the correspondin

Zone li

ht will be ON. Secure these

zones before proceedin

. If any zones cannot be secured, see Bypassin

zones below.

2 Enter your user code. The Green Ready li

ht will

o out, the Red Armed li

ht will li

ht.

• If you make a mistake enterin

your code, press



and re-enter the code.

3 Leave the premises through the Exit/Entry door. If the keypad gives a steady tone you have taken

too long. Enter your code again to disarm system and then re-enter code and leave.

Easy Arm

The Easy Arm feature allows the system to be armed by simply pressing



followed by



. This will

allow the easy arming of the system by someone who is not a regular system user.

Bypassing Zones

If an open zone cannot be immediately fixed it can be left unprotected, or

Bypassed

,while the rest of the

system is Armed. To Bypass a zone:

1Press



followed by the zone number to be Bypassed. The Bypassed zone’s light will flash slowly.

2 Enter your user code. The Green Ready light will go out and the Red Armed light will light.

3 Leave the premises through the Exit/Entry door.

When the system is subsequently disarmed, all bypassed zones will be reset, ready to be armed again.

If it is necessary to bypass any inoperative zone(s), it is important to have the zone(s) repaired as soon as

possible. A bypassed zone does not provide any protection, compromising system security.

Arming Your System

SYSTEM

READY

ZONE 3

ZONE 1

ZONE 2

ZONE 4

ARMED

Oi220a

page 6 Tuesday, September 16, 1997 08:30

www.ealarm.com.my

Protecting Yourself While at Home

1 Before armin

your system, make sure the Green Ready li

ht is ON. This indicates that all of your

protective zones are secure. If any zones are open, the correspondin

Zone li

ht will be ON. Secure

those zones before proceedin

2 Enter your user code. The Green Ready li

ht will

o out, and the red Armed li

ht will li

ht.

3Before your exit delay expires, press

to bypass any interior zones, deactivating devices such

as motion sensors, and allowing free movement throughout the premises. The Zone light of any

bypassed zones will flash slowly.

• Your system may have been programmed for Automatic Interior Bypass , in which case it will

recognize that you have not left the premises and will automatically bypass any interior zones.

Instant Mode

Pressing

followed by



will cancel the Entry delay , activating the “Instant” mode. This is typically

done in the evening when all family members are home for the night. Instant Mode can be activated at any

time after the system has been armed. The Red Armed light will flash rapidly while in the Instant Mode.

Easy Exit (optional)

Your System may have been programmed to allow Easy Exit, which allows a user to exit the premises

with the system armed. By pressing



followed by



, the protection is removed from the Exit/ Entry

zone for 3 minutes. This will allow, for example, an early morning commuter to exit the house in the

morning, without having to disarm and rearm the system, waking the family.

Arming With a System Trouble Present (the 9System Light is Lit)

If the XP400 has a system trouble present, the

SYSTEM li

ht will be lit and the ke

pad sounder

pulsin

. If

ou cannot immediatel

clear the s

stem trouble, the s

stem can still be armed. Simpl

press



to view the trouble, press



again to reset the trouble and then arm the system.

For more information, refer to page12. Note: System troubles should be repaired as soon as possible.

Arming Your System

SYSTEM

READY

ZONE 3

ZONE 1

ZONE 2

ZONE 4

ARMED

Oi220a

page 7 Tuesday, September 16, 1997 08:30

www.ealarm.com.my

Emergency Buttons

The two sets of emergency buttons, if programmed, are always active whether the system is armed or

disarmed. Discuss these buttons with your installer. The emergency signal will only be activated when

the two respective buttons are pressed at the same time.

Auxiliary Alarm: Simultaneously press



to alert the central station of an auxiliary

emergency, if so programmed.

(The nature of this emergency alarm is to be determined by the installer)

Police Emergency: Simultaneously press



to sound a police emergency alarm, and to alert

the central station of a fire emergency, if so programmed.

Emergency Conditions



Ambush Alarm

In the event that you are forced by an intruder to disarm your system, the ambush alarm can be

activated. Disarming the system with the Ambush Code will cause the system to disarm and

simultaneously send a silent ambush alarm signal to Central Station. If your system has the Ambush

feature enabled, the code assigned as the User 4 code will function as your Ambush Code.

Auxiliary

Emergency

Enabled?

Yes No



Police



Emergency

Enabled?

Yes No

Ambush

Alarm

Enabled?

Yes No

Oi220a

page 8 Tuesday, September 16, 1997 08:30

www.ealarm.com.my

Disarming Your System when Returning

1 Enter your premises throu

h the Entry/Exit door. The keypad will sound a steady tone to remind you to

disarm the system before your Entry Delay time expires.

2 Enter your user code. The Red Armed li

ht will

o out, indicatin

that the system has been disarmed.

Note: If you make a mistake enterin

your code, press the



key and re-enter the code.

Alarm Indication

If the Red Armed light is flashing rapidly, an alarm occurred while you were away.

Proceed with caution!

For your own protection, leave immediately and call authorities from a neighbor’s phone .

Silencing an Alarm

In the event that the system goes into alarm due to a violated burglary zone, the bell or siren will sound and

the keypad sounder will also activate. To silence the system, enter your User code. The zone light of the

zone which went into alarm continue flashing until



is pressed to reset the alarm memory.

SYSTEM

READY

ZONE 3

ZONE 1

ZONE 2

ZONE 4

ARMED

Disarming Your System / Silencing an Alarm

Oi220a

page 9 Tuesday, September 16, 1997 08:30

www.ealarm.com.my

Special Functions 

By pressing



followed by the appropriate key, (do not press simultaneously) these special functions and features can

be enabled:



Easy Arm (when system is disarmed)

The Easy Arm feature allows the system to be armed by

pressing

followed by



. This will allow the easy

arming of the system by someone who is not a regular

system user.

!

Easy Exit (when system is armed)

This function (if programmed) allows an occupant to leave

the premises without disarming the system. Pressing



followed by



while the system is armed will start a 3

minute period, during which you can leave through the

Exit/ Entry door.



Bell / Battery Test

Pressing



followed by



will cause the bell, or siren to

sound for 2 seconds. This will also initiate a test of your

battery to make sure it is adequately charged. The XP-400

also performs an automatic battery test very 24 hours



Access Output

If programmed, pressing



followed by



will activate

the Access Output which may be configured to open a

door strike, turn on lighting, or activate some other special

feature your installer has provided.



Instant Mode

Pressing



followed by



will cancel the Entry delay

and put the system into the “Instant” mode. This is typic-

ally done in the evening when all family members are home

for the night. When the system is disarmed, the Instant

mode will be canceled.



Chime Mode On / Off

Pressing



followed by



will activate / deactivate the

door chime. Activating this feature will cause any door

to beep the keypad sounder when it is opened.



Program Mode

Pressing



followed by



will enable the “Program

Mode”, which will allow you to program and erase user

codes. (see Programming user codes, page 14)



Kepad Sounder On / Off

Pressing



followed by



will deactivate / activate the

keypad sounder, depending on its present state. By

activating sleep mode on a keypad installed in a bedroom,

for example, you effectively turn off that keypad’s sounder.

However, any other keypads on the system will still sound

normally.

Oi220a

page 10 Tuesday, September 16, 1997 08:30

www.ealarm.com.my

Your Installer has assigned a User 1 Code which may be used to not only Arm and Disarm the system, but

also to enter the User Program Mode, where you can program and/or reprogram up to 4 User Codes. The

following explains how you will use this code to program or erase additional user codes.

Entering the User Program Mode

Press



followed by



and then enter the User 1 code. The Armed, Status and 9System Lights

will flash, and the keypad will beep 4 times. You are now in the User Program mode.

Zone lights 1 through 4will light to indicate any User Codes presently programmed.

Programming / Reprogramming User Codes

1Press the User number to be programmed. (For example, press



to program the User 2 code.).

The keypad will beep 2 times and the corresponding Zone light will flash to indicate the user

number you are about to program.

2Press in the 4 digits of the new User 2 code, the keypad will beep 4 times.

3 If there are more user codes to be programmed, return to step 1 above, otherwise, go to Exiting the

User Program Mode below.

Erasing a User Code

1Press the User number to be erased. The keypad will beep 2 times and the corresponding Zone light

will flash to indicate the user number you are about to erase.

2Press



. The zone light will go out to indicate that the user code has been erased.

3If there are more user codes to be erased, return to step 1 above, otherwise, go to Exiting the user

Program Mode below.

Exiting the User Program Mode

When you are done programming or erasing User codes, press



to Exit the User Program Mode.

Programming User Codes

SYSTEM

READY

ZONE 3

ZONE 1

ZONE 2

ZONE 4

ARMED

Oi220a

page 11 Tuesday, September 16, 1997 08:30

www.ealarm.com.my

The XP400 is constantly monitoring its own components, as well as all critical services, such as AC Power

and the Telephone line, to insure that it is always ready to provide the protection for which it was designed.

When a system trouble does occur, it will caution you by lighting the Yellow

SYSTEM light and beeping the

keypad buzzer. If you cannot immediately clear the system trouble, the system can still be used. Simply

press



to view the trouble as described below, and then arm the system.

In order to determine the nature of the trouble, press



, count the number of keypad beeps and observe

the number of the illuminated zone light. Refer to the following table to determine the cause of the trouble.

If there is more than one trouble to be viewed, pressing



will scroll to the next, and then exit the

SYSTEM mode if there are no additional troubles to view.

9System Troubles

Keypad Beeps or

SYSTEM Flashes Zone light

ON System Trouble

Condition Action

Beep

1 AC Power Failure This trouble will occur if AC power is not present. Make sure

system transformer is plugged into AC receptacle and check

circuit breaker, otherwise call installing company for service.

Beep

2 Low Battery If there has been a recent power failure, the battery may be

partially depleted and must be recharged by the control

panel. If the trouble does not go away in 24 hours, call in-

stalling company for service.

Beep

3 Communication

Failure The system was not able to report to central station. If this is

due to a temporary interruption in the telephone service, the

trouble can be cleared when the service is restored by press-

ing



. Otherwise, call installing company for service.

Beep

4 Telephone Line Cut The telephone line has failed. If telephone service has been

temporarily interrupted, the trouble will clear it is when re-

stored. Otherwise, call installing company for service.

SYSTEM

READY

ZONE 3

ZONE 1

ZONE 2

ZONE 4

ARMED

Oi220a

page 12 Tuesday, September 16, 1997 08:30

www.ealarm.com.my

Table des matières

Autres manuels NAPCO Système de sécurité

NAPCO

NAPCO Commercial GEMC Manuel utilisateur

NAPCO

NAPCO XP-400 Fiche technique

NAPCO

NAPCO FREEDOM - Manuel utilisateur

NAPCO

NAPCO Magnum Alert-800 Manuel utilisateur

NAPCO

NAPCO FREEDOM F-64TPBR Manuel utilisateur

NAPCO

NAPCO XP-400 Manuel

NAPCO

NAPCO MA3000 Manuel utilisateur

NAPCO

NAPCO MAGNUM ALERT-725 Manuel utilisateur

NAPCO

NAPCO Gemini GEM-X255 Manuel utilisateur

NAPCO

NAPCO MAGNUM ALERT 854 SYSTEM Guide produit

NAPCO

NAPCO iSecure Manuel d'installation

NAPCO

NAPCO MAGNUM ALERT-850 Manuel utilisateur

NAPCO

NAPCO FREEDOM64 Manuel utilisateur

NAPCO

NAPCO PRO410 Manuel utilisateur

NAPCO

NAPCO MAGNUM ALERT-725 Manuel utilisateur

NAPCO

NAPCO MAGNUM ALERT 825 SYSTEM Manuel utilisateur

NAPCO

NAPCO MAGNUM ALERT 900 SYSTEM Manuel utilisateur

NAPCO

NAPCO Freedom F-64 Manuel utilisateur

NAPCO

NAPCO XP-400 Manuel d'installation

NAPCO

NAPCO XP-400 Fiche technique

NAPCO

NAPCO STARLINK SL-1 FD-T Manuel utilisateur

NAPCO

NAPCO MAGNUM ALERT 854 SYSTEM Manuel utilisateur

NAPCO

NAPCO MAGNUM ALERT-825 Manuel utilisateur

NAPCO

NAPCO Magnum Alert 1016e Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur