Nailor 35S Manuel utilisateur

Nailor Industries, Inc. reserves the right to change any information concerning product or specification without notice or obligation.

DISCHARGE

DUCT PRIMARY

INLET

PRIMARY

AIRFLOW

INDUCED

AIR

ELECTRIC

HEATER

SECTION

INDUCED AIR

INDUCTION PORT

(DO NOT OBSTRUCT)

STEALTH

ATTENUATOR

DISCHARGE

DUCT PRIMARY

INLET

PRIMARY

AIRFLOW

HOT WATER

SECTION

General

Receiving Inspection Checklist

Visually inspect unit for shipping damage before unwrapping

any packaging material. Report any damage immediately to the

delivering carrier.

After unpacking the unit, check it again for shipping damage. If any

shipping damage is found, report it immediately to the delivering

carrier.

Notify your local Nailor representative of damage and arrange for

repair or replacement.

Check that the unit is labeled as intended and deliver to appropriate

site location.

Store units in a clean, dry location.

Caution: Do not use the inlet collar, damper shaft, airow

sensor, electrical conduit, water coil extremities, drip pan,

or tubing as a handle to lift or move assembly. Damage to

the unit, unit accessories or controls may result.

Safety Precautions

a. All person(s) involved in installation process shall be qualied

according to all relevant local codes and standards.

b. Beware of other building utilities and electrical wiring during

installation process.

c. The unit installed shall be used only as intended. Any unintended

use shall therein result in immediate forfeiture of manufacturer

assumed warranty, responsibility and liability of product and

associated components. Contact your local Nailor representative

for questions.

d. Warning: Make sure all electrical power to the unit has

been disconnected and any capacitors fully discharged

before servicing. Failure to do so could result in injury or

death.

e. During brazing process, make sure to protect any surrounding

ammable materials, using barriers where applicable and always

have a re extinguisher accessible.

Caution: Any improper product handling, installation,

servicing, or operation resulting in personal injury and

property damage shall void any manufacturer assumed

legal responsibility.

Installation

Supporting the Assembly

Suspend the unit from the building structure in the horizontal plane

and ensure the unit is level to guarantee proper performance. Hanger

rods or straps (by others) should be securely attached to joists or to

mounting anchors which are properly secured to slab construction with

lugs or poured in place anchors. Be careful not to obstruct the bottom

access panel in order to maintain clearance for blower service. When

requested, the unit is supplied with optional hanger brackets (shipped

loose for eld mounting) for use with hanger rod up to 3/8" (9.5) dia.

Hanger brackets or straps should be screwed to the top corner posts

(35S only) or unit casing sides (other models) or alternatively onto the

inlet and outlet ends of the unit. See Figures 1 and 2.

Caution: Nailor Fan Powered Terminal units are too

heavy to suspend with the ductwork and must be

independently supported.

Duct Connections

All ducts should be installed in accordance with SMACNA guidelines.

Slip each inlet duct over the inlet collar of the terminal. Fasten and

seal the connection by the method prescribed in the job specication.

The diameter of the inlet duct in inches must be equal to the nominal

size of the terminal inlet. The inlet collar of the terminal is 1/8" (3)

smaller than the nominal duct size to allow it to t inside the duct.

Important: Do not insert ductwork inside the inlet collar

of the assembly.

Installation and Operation Manual (IOM)

Fan Powered Terminal Units

Model Series: 35S(ST), 35SXC, 35N,

37S(ST) and 37N

7-6-23 IOM-FPTU Page 1 of 10

Figure 1: Fan Powered Terminal Unit Support Using Hanger Straps

(Model 35SE illustrated).

Figure 2: Fan Powered Terminal Unit Support Using Hanger Brackets

and Rods (Models 35SWST and 35SW illustrated).

USE "Z" BRACKET

WITH

ELECTRIC OR

HOT WATER HEAT

Nailor Industries, Inc. reserves the right to change any information concerning product or specification without notice or obligation.

For optimum performance, 2 to 3 equivalent diameters of straight

duct should be installed prior to the inlet of the unit. Rectangular

discharge opening is designed for a anged duct connection. A clear

area around the opening has been left for screw penetration. Fasten

and seal all connections by method prescribed in the job specication.

Minimum Access

Make appropriate accommodations for access panel removal. If unit

is to be installed in hard ceiling/wall application, refer to Nailor

fan powered terminal unit submittals for specic dimensions before

installing to assure there is access to the unit and components after

installation is complete. Nailor 35S fan powered VAV terminal units

have access panels on the top, bottom and side. Nailor 35N units

have only bottom panels. Model 37S and 37N have top and bottom

panels. Removable top and bottom access panels are secured as

standard with screws. However, if the ¼ turn fastener access panel

option is supplied, the bottom panel screws are replaced with two

quick-connect latches.

Units with a removable top access panel are secured with two

additional screws in the middle for shipping and handling. These

additional screws can be removed after the unit is hung for quicker

service if needed.

For low voltage control enclosure access, a minimum of 18" (457) is

recommended. Specic control enclosure location is indicated on

product submittals. Low voltage control enclosures have removable

covers that are attached with sheet metal screws. High voltage

controls enclosures have access panels that are equipped with

hinges. For clearances for full opening of hinged access doors, refer

to project specications, submittal sheets and NEC.

Important: These recommendations do not preclude

NEC or local codes that may be in effect, which are the

responsibility of the installing contractor.

Field Wiring

All eld wiring must comply with NEC and local codes. Disconnect

switches are optional. Wiring diagrams can be found on labels

afxed to the exterior/interior of the control box enclosure. Unless

specically requested by customer, all units are wired for a single

point connection to the fan and electric heater (if present). All electric

heaters will be staged per specication. Motors rated for 277 or 120

VAC on units with 480 or 208 VAC ratings respectively are always

connected between the neutral and L1 terminals. The installing

electrician should rotate the incoming electric service by phase to

help balance the building electric load.

Fuse size designates the size of the internal fuse if it is supplied.

Maximum Overcurrent Protection (MOP) designates the largest

breaker or fuse in the electrical service panel that can be used to

protect the unit. See Table 1 for calculation details.

Electrical Suggestions and Requirements

1. Provide a safety disconnect per NEC 424-19, 20, 21.

2. Disconnect the power supply before wiring or servicing unit. If+ a

disconnect switch is present, it should be in the OFF position while

making power connections or repairs.

3. All units with electric heat should have copper wires sized for minimum

circuit ampacity (MCA). See Table 1 for calculation details.

4. Follow wiring diagrams and instructions mounted on the unit.

480V/3 phase heaters, for example, require a neutral wire in

addition to the full sized ground wire. NEC 424-15 and 250 also

require that all units be grounded.

Water Pipe Connections

Exercise extreme caution during "sweating" or brazing process of coil

piping to avoid applying excessive heat to components associated

with valve package. This could cause irreversible damage, requiring

immediate replacement of parts. Make sure valves are in full open

position during brazing process. Heat can be dissipated more

effectively by wrapping a wet towel around the valve body during the

brazing process.

Control Start-up and Operation

Your local Nailor Representative can provide detailed information

about start-up and operating procedures for Nailor’s digital, analog,

and pneumatic controls. For specic information on controls provided

by other manufacturers contact the control manufacturer’s local or

national ofce. This applies whether the controls were factory or eld

installed.

NOTE

Note: Digital controllers may use specic communication

addresses based on Building Management Systems,

Architecture and original engineering drawings.

Installing the terminal in a location other than that noted

on the label may result in excessive start-up labor.

Primary Air Damper and Fan Adjustment

Before starting the fan motor:

a. If lters are required, make sure they are installed as intended.

b. Make sure duct system is clear of all debris and foreign objects.

c. Ensure unit enclosure, blower housing and blower wheel are free

of any debris and foreign objects.

Starting the fan motor:

1. Start motor and let it run-in at least 15 minutes. During run-in,

check ductwork connections for leaks and repair if necessary.

2. All Nailor fan powered VAV terminal units incorporating PSC

motors use a solid state SCR speed controller to adjust motor

speed and consequently air volume. Speed controllers have built-in

maximum and minimum stops as detailed on the fan performance

pages in the Nailor VAV Terminal Unit catalog. Turning the manual

fan speed control counterclockwise will increase the fan speed;

clockwise will decrease speed. The fan speed control is located

on the side of the motor controls enclosure.

3. For series units, set the unit to full cooling. Adjust and set primary

maximum cfm by measuring the airow with a manometer

attached between the gauge ports in the pneumatic tube leading

to the high and low sides of the inlet air pick-up. A chart is attached

to the side of the unit showing airow vs. pressure for different inlet

sizes. Adjust and set remote balancing dampers, if present. Do not

worry about airow at this time; just proportion the outlets with the

dampers. Be sure to leave the dampers in the most possible open

position. This will generate the minimum noise level. Adjust the fan

speed control until the required CFM is obtained (by measuring

the air quantity at the room outlets or by zeroing the induction air if

primary and fan match). Fan should be adjusted with primary air

at maximum set point to ensure that no supply air is discharged at

the induction port. Recheck the fan and primary airows when the

damper is reset to the minimum set point.

4. For parallel units, turn the fan off, and set the primary air in the

same manner as described for series units. Proportion the diffusers

as above. Reset the primary airow to the design fan turn-on point.

Measure the airow again to verify proper airow. Turn the fan

on. Allow the primary air damper to come under control after the

fan is started, and then adjust the fan until the prescribed airow

is achieved by measuring the air quantity at the room outlets. Be

sure to allow the primary air damper to stabilize after each fan

adjustment and prior to measuring the airow. Turn the fan off and

verify the minimum airow point on the damper.

5. For units equipped with ECM motors, set the primary air dampers

as described in (3). Set the fan as described on the ECM MOTORS

IOM, page 1. Proportion the dampers after the fan is set. Remember

to adjust the dampers so that they are in the most open condition

after proportioning. This will generate the minimum noise.

Page 2 of 10 7-6-23 IOM-FPTU

Nailor Industries, Inc. reserves the right to change any information concerning product or specification without notice or obligation.

7-6-23 IOM-FPTU Page 3 of 10

Label Example

Maintenance Procedures

Warning: Electrical Hazard!

Before Servicing, disconnect all sources of electrical power,

including the complete discharge of any electric current stored

in capacitors included in the wiring structure. Practice good

lockout/tagout procedures to prevent energizing of the unit

during servicing. Failure to comply with previous statements

could yield personal injury or even result in death.

Fan and Motor

Nailor fan powered terminal units are equipped with permanently

lubricated motors. Inspect fan and motor assembly for dust and dirt as

often as dictated by operating environment. Clean assembly if necessary.

If fan motor does not run, do the following:

a. Check for free rotation of blower wheel. Make sure no foreign

objects are in fan. Look for signs of freight or job site damage.

b. Check power supply. Disconnects should be in the "ON" position.

Optional fusing should also be inspected. Check transformer for

proper output.

c. Check for proper control signals and PE switch setting (if provided)

and relay function.

Fan motor runs but emits excessive noise

a. Maximum airow may be too high, or discharge static pressure

may be incorrect.

b. Blower may have clearance problems. Make sure all components

are securely attached.

c. Verify integrity of ductwork. Leaks or loose connections could

cause noise. Check for rattling diffusers or rattling or incorrectly

adjusted balancing dampers.

Fan motor runs, but airflow too low:

a. May be due to ductwork restrictions, dirty air lters or clogged

water coils.

b. Readjust fan speed control on control card.

Discharge static pressure may be incorrect. Check balancing dampers.

d. Conrm signal from the motor card to the motor by measuring the

plug at the motor.

If repair or replacement is required

Disconnect all power before servicing. Motor and fan should be

removed as an assembly. Remove the four hex nuts from mounting

lugs holding the fan assembly to the discharge panel, and remove

the assembly through any convenient access panel. Do not allow

assembly to hang from wiring. If removing motor from blower, rst

loosen the set screw holding the blower wheel to the motor shaft.

Remove the three screws holding the motor to the fan housing, and

slide motor and fan housing apart.

To put the assembly back together, reverse the procedure. Be sure

to align the blower set screw with the at section of motor shaft.

NOTE

Note: Over-tightening motor mounting screws may

crush isolation bushing, causing excessive fan noise.

Primary Air Damper Replacement

Nailor’s primary air valve assembly is not repairable. The entire

assembly should be replaced if it is damaged.

Labels

Each fan powered terminal unit is shipped with a nameplate label

afxed to the control casing. Principle nameplate data on the label

typically include Order-Serial number, Model number, Unit Size,

Motor horsepower, Amperage, MOP, Heater (if present) data, Supply

voltage and Airows. Also provided are calibration, airow, as well as

other labels as necessary. We suggest that you read all labels before

beginning installation. If you have any questions, please contact your

local Nailor Representative. Their phone numbers can be found on

our website at nailor.com.

Fan Powered

Terminal Unit

(Unite Terminale @

Ventilateur Intégré)

Date (Date)

Model (Modèle)

Unit Size-Inlet Size

(Diamètre D'Entrée)

Control Voltage

(Voltage De Contrôle)

Control Sequence

(Séquence De Contrôle)

Volt Amp (Volt-Ampère)

5-Jul-2023 Serial No. (No. De Série)

Tag No. (No. D'étiquette)

Voltage (Voltage)

Phase (Phase)

Stages (Étapes)

HZ (HZ)

Motor HP (Moteur HP)

Motor Voltage

(Voltage Du Moteur)

Motor Amp

(Ampérage Du Moteur)

Hot Water Coil Rows

(Nombre De Rangées Serpentin Eau Chaud)

Chilled Water Coil Rows

(Nombre De Rangées Serpentin Eau Froid)

KW/HP

Heater (Chauffage)

Motor (Moteur)

Total (Totale)

Amps (Ampères) Ampacity (Ampacitée)

Max. Overcurrent Protection

(Resistance Des Fusible Max.)

Internal Fuse Size

(If Supplied)

Total

(Totale)

Each Cir.

(Chaque

Circuit)

Each Stg.

(Chaque

Étape)

Total

(Totale)

Each Cir.

(Chaque

Circuit)

Each Stg.

(Chaque

Étape)

Total

(Totale)

Each Cir.

(Chaque

Circuit)

Each Stg.

(Chaque

Étape)

Total

(Totale)

Each Cir.

(Chaque Circuit)

Each Element Rated @

(Chaque Element Classifier A)

VAC.

AWG. Min Wire Size (Min Diamètre De Fil) :

Min. Heating CFM (Min. PCM) :

Use wire suitable for at least 75 °C,

L1 is color coded black, L2 is blue, L3 is red,

Control wires coded as marked,

Use copper conductors only.

Utiliser un fil métallique qui convient au moin 75 °C,

L1 est colore noire, L2 est blue, L3 est rouge,

Les fils de contrôle son identifiée comme marque,

Utilise des conducteurs de cuivre seulement.

Primary CFM (Max/Min) :

Fan CFM :

Primary L/S (Max/Min) :

Fan L/S :

D35SE

3-8

155258-10

208

62.5

6.50

13.00

62.5

31.25

78.13

39.07

0.00

62.50

78.13

N/A

3.25

890 / 360

890

420 / 170

420

208

910.00

13.00

Primaire PCM (Max.Min):

Ventilateur PCM:

Primaire L/S (Max.Min):

Ventilateur L/S:

Fan Powered

Terminal Unit (Unite Terminale @

Ventilateur Intégré)

Date

(Date)

Model

(Modèle)

(Diamètre D'Entrée)

Control Voltage

(Voltage De Contrôle)

Control Sequence

(Séquence De Contrôle)

Volt Amp (Volt-Ampère)

5-Jul-2023

Serial No.

(No. De Série)

Tag No. (No. D'étiquette)

Voltage (Voltage)

Phase

(Phase)

Stages (Étapes)

HZ (HZ)

Watts (Watts)

Motor Voltage

(Voltage Du Moteur)

Motor Amp

(Ampérage Du Moteur)

Hot Water Coil Rows

(Nombre De Rangées Serpentin Eau Chaud)

Chilled Water Coil Rows

(Nombre De Rangées Serpentin Eau Froid)

KW/Watts

Heater (Chauffage)

Motor (Moteur)

Total (Totale)

Amps

(Ampères)

Ampacity

(Ampacitée)

Max. Overcurrent Protection

(Resistance Des Fusible Max.)

Internal Fuse Size

(If Supplied)

Total

(Totale)

Each Cir.

(Chaque

Circuit)

Each Stg.

(Chaque

Étape)

Total

(Totale)

Each Cir.

(Chaque

Circuit)

Each Stg.

(Chaque

Étape)

Total

(Totale)

Each Cir.

(Chaque

Circuit)

Each Stg.

(Chaque

Étape)

Total

(Totale)

Each Cir.

(Chaque Circuit)

Each Element Rated @

(Chaque Element Classifier A)

VAC.

AWG. Min Wire Size (Min Diamètre De Fil) :

Min. Heating CFM (Min. PCM) :

Use wire suitable for at least 75 °C,

L1 is color coded black, L2 is blue, L3 is red,

Control wires coded as marked,

Use copper conductors only.

Primary CFM (Max/Min) :

Fan CFM

Primary L/S (Max/Min) :

Fan L/S

D35SE

3-8

155258-10

208

62.5

13.00

6.50

62.50

31.25

78.13

0.00

78.13

39.07

N/A

3.25

208

890 / 360

890

420 / 170

420

910.00

(Ventilateur PCM) (Ventilateur L/S)

Primaire PCM (Max.Min) Primaire L/S (Max.Min)

Unit Size-Inlet Size

Utiliser un fil métallique qui convient au moin 75 °C,

L1 est colore noire, L2 est blue, L3 est rouge,

Les fils de contrôle son identifiée comme marque,

Utilise des conducteurs de cuivre seulement.

Nailor Industries, Inc. reserves the right to change any information concerning product or specification without notice or obligation.

Minimum Circuit Ampacity

MCA = 1.25 x (Load 1 + Load 2 + Load 3 + Load 4)

Maximum Overcurrent Protection

MOP = (2.25 x load 1) + load 2 + load 3 + load 4

If the calculated MOP does not equal the standard current rating of an Overcurrent protective device (typically even multiples of 5),

then the marked MOP is the next lower standard rating.

Exceptions:

1. The marked MOP will be the next higher standard rating than the computed value, if the next lower standard rating is less than 125

percent of the current rating of an electric heater load when such heater is involved.

2. If the computed value for MOP is less than the MCA, then the marked MOP is increased to the largest MOP appropriate for the

MCA.

3. If the MCA does not correspond to a standard protective device rating, the next higher standard rating of the protective device will

be marked if this rating does not exceed 800 A.

For Nailor Fan Powered Terminal Units and Fan Powered Terminal Units, Load 1 is the largest motor current, Load 2 is the sum

of all other motor currents, and Load 3 is the heater current. Load 4 is used for other loads greater than 1.0 ampere and can be

considered zero for most standard products.

For Nailor Variable Air Volume Units, Load 1 and Load 2 are considered zero.

Load 3 is the heater current Load 4 is used for other loads greater than 1.0 ampere and can be considered zero for most standard

products.

(Motor currents are determined by product application test in accordance with UL 1995 and may not be the same as the motor

manufacture’s FLA marking.)

All formulae, denitions, and exceptions are cited from Underwriters Laboratories Inc. Standard for Safety for Heating and Cooling Equipment, UL

1995 Fifth Edition (Sec. 44.14.44.15) CAN/CSA-C22.2 No. 236 Fifth Edition

Page 4 of 10 7-6-23 IOM-FPTU

MCA and MOP Calculations

.40

.02

.03

.04

.05

.06

.07

.08

.09

.20

.50

.60

.70

.80

.90

1.0

.30

.10

.15

30 300 400 700 1000 1500 50003000200080605040 200100 150 500

CFM

DIAMOND FLOW SENSOR

FIELD CALIBRATION CHART

MODEL SERIES:

3100, 3230, 3240, 33SZ, 35N, 35S,

35SST, 36VRR, 37N, 37S & 37SST

DFSCC-2

11-2022

SENSOR ∆P (INCHES W.G.)

SIZE 4 ROUND

SIZE 5 ROUND

SIZE 6 ROUND

SIZE 7 ROUND

SIZE 8 ROUND

SIZE 9 ROUND

SIZE 10 ROUND

SIZE 14 x 10 RECT.

SIZE 14 ROUND

SIZE 16 ROUND

SIZE 18 OVAL

Inlet K-Factor

Size

4 Round 182

5 Round 325

6 Round 455

7 Round 657

8 Round 899

9 Round 1158

10 Round 1497

12 Round 2048

14 Round 2742

16 Round 3683

14 x 8 Rect. 2035

14 x 10 Rect. 2417

18 Oval 4323

CFM = K x ∆P

ALLOWABLE PNEUMATIC LO

SETTING MIN. ∆P = O.O3" W.G.

SIZE 12 ROUND (14x8 RECT.)

Sample Diamond Flow Sensor Calibration Label

ECM MOTOR FAN CALIBRATION TABLE

FAN POWERED TERMINAL UNIT

MODEL SERIES: 35S & 35SST • UNIT SIZE 3 • 120/208/230/277 VAC 2/26/23

0-10 0-10 0-10 0-10

REF. REF. REF. REF.

138 0.50 429 2.89 747 5.29 1023 7.68

146 0.57 438 2.96 756 5.36 1030 7.75

155 0.64 448 3.03 765 5.43 1037 7.82

163 0.71 457 3.10 774 5.50 1044 7.89

171 0.78 466 3.17 783 5.57 1051 7.96

179 0.85 475 3.24 791 5.64 1058 8.03

188 0.92 485 3.31 800 5.71 1065 8.10

196 0.99 494 3.39 809 5.78 1072 8.17

204 1.06 503 3.46 818 5.85 1079 8.24

213 1.13 513 3.53 826 5.92 1086 8.31

221 1.20 522 3.60 835 5.99 1093 8.38

229 1.27 531 3.67 843 6.06 1100 8.45

238 1.34 541 3.74 852 6.13 1108 8.52

246 1.41 550 3.81 860 6.20 1115 8.59

254 1.49 560 3.88 869 6.27 1122 8.66

263 1.56 569 3.95 877 6.34 1129 8.73

271 1.63 579 4.02 885 6.41 1136 8.80

280 1.70 588 4.09 893 6.48 1143 8.87

288 1.77 598 4.16 901 6.55 1151 8.94

297 1.84 607 4.23 909 6.62 1158 9.01

305 1.91 616 4.30 917 6.69 1166 9.09

314 1.98 626 4.37 925 6.76 1173 9.16

322 2.05 635 4.44 933 6.83 1181 9.23

331 2.12 645 4.51 941 6.90 1189 9.30

340 2.19 654 4.58 949 6.97 1197 9.37

349 2.26 663 4.65 956 7.04 1205 9.44

357 2.33 673 4.72 964 7.11 1213 9.51

366 2.40 682 4.79 971 7.19 1222 9.58

375 2.47 691 4.86 979 7.26 1230 9.65

384 2.54 701 4.93 986 7.33 1239 9.72

393 2.61 710 5.00 994 7.40 1248 9.79

402 2.68 719 5.07 1001 7.47 1257 9.86

411 2.75 728 5.14 1008 7.54 1266 9.93

420 2.82 737 5.21 1016 7.61 1276 10.00

THIS UNIT HAS BEEN FACTORY SET AT ____________ CFM.

www.nailor.com SUBJECT TO CHANGE WITHOUT NOTICE

Digital Control Algorithm:

CFM=0.027717307(VDC)5‐0.61146699(VDC)4+4.155391639(VDC)3‐8.60626115(VDC)2+124.7107364(VDC)+77.19940471

VDC=‐1.2214E‐14(CFM)5+3.95345E‐11(CFM)4‐4.43622E‐08(CFM)3+2.07462E‐05(CFM)2+4.104313E‐03(CFM)‐0.340841705E+0

RE-CALIBRATION IS NOT REQUIRED UNLESS THE ZONE DESIGN AIRFLOW REQUIRMENT HAS CHANGED. THE BOLD LINES INDICATE MIN AND

MAX CFM FOR THE UNIT. VARIATIONS IN FLOW IS IN +/- 5% or +/- 30 CFM WHICHEVER IS GREATER EXCEPT IN GRAY AREA. DATA

REPRESENTED IN THIS CHART IS AT STANDARD CONDITIONS OF TEMPERATURE, PRESSURE AND HUMIDITY I.E. SCFM. FAN TURNS OFF

BELOW 0.50Vdc.

CFM vs VDC

(

erial Units

)

CFM CFM CFM CFM

Application Charts for ECM Motors

Airflow Direction (affixed to inlet collar)

AIR FLOW (ECOULEMENT DE L'AIR)

LOW (BAS) HIGH (HAUT)

HIGH (HAUT) LOW

Table 1.

Nailor Industries, Inc. reserves the right to change any information concerning product or specification without notice or obligation.

7-6-23 IOM-FPTU Page 5 of 10

Model Series Fan Powered Terminal Units Replacement Parts

NAILOR EZVAV DIGITAL CONTROLS

Code Description

Controller/Actuators:

BAC-8001-36 EZVAV Digital Controller (SD Clg only)

BAC-8005-36 EZVAV Digital Controller (SDRH, FP)

BAC-8007-36 EZVAV Digital Controller (DD master)

TSP-8001-36 EZVAV Digital Controller (DD slave)

Room Temperature Sensors:

STE-8001W36 EZVAV Room Temp Sensor – Digital display

STE-8201W36 EZVAV Room Temp Sensor – Digital display w/

motion sensor

STE-6014W36 EZVAV Room Temp Sensor – Rotary dial

ECRJ45-25 Ethernet cable RJ-45, 25 ft.

ECRJ45-35 Ethernet cable RJ-45, 35 ft.

ECRJ45-50 Ethernet cable RJ-45, 50 ft.

ECRJ45-75 Ethernet cable RJ-45, 75 ft.

STE-1401 Air temp. sensor (HCCO, DAT)

ELECTRICAL COMPONENTS

RAPP Code

Description Part

Number

Disconnect Switches

EC-DISTG251P Toggle Disconnect Switch

1P,600V,25A H1-0212A

EC-DISTG403P Toggle Disconnect Switch

3P,600V,40A H1-0220Z

EC-DISTG603P Toggle Disconnect Switch

3P,600V,60A H1-0221Z

EC-DISINT25A Interlocking Disconnect

Switch3P,600V,25A H1-0215Z

EC-DISINT40A Interlocking Disconnect

Switch3P,600V,40A H1-0216Z

EC-DISINT60A Interlocking Disconnect

Switch3P,600V,60A H1-0217Z

EC-DISINTHDL Interlocking Disconnect Handle H1-0215C

EC-DISINTSFT Interlocking Disconnect Shaft H1-0215D

Contactors

EC-CONM50A1P Contactor MAG 1P,600V,40Amp H1-0635

EC-CONM40A1P Contactor MAG 1P,600V,40Amp H1-0636

EC-CONM30A1P Contactor MAG 1P,600V,20Amp H1-0654

EC-CONM50A2P Contactor MAG 2P,600V,40Amp H1-0658

EC-CONM40A2P Contactor MAG 2P,600V,30Amp H1-0655

EC-CONM30A2P Contactor MAG 2P,600V,20Amp H1-0652

EC-CONM50A3P Contactor MAG 3P,600V,40Amp H1-0640

EC-CONM40A3P Contactor MAG 3P,600V,30Amp H1-0639

EC-CONM30A3P Contactor MAG 3P,600V,20Amp H1-0653

SCR/SSR

EC-SCR

SCR Elect. Heat controller, 600V, 1ph, 45A

H1-2064

EC-SSR

SSR Elect. Heat controller, 600V, 1ph, 45A

H1-2082

ECM Motor Wiring harness

EC-HARNESS1 Wiring Harness, Card to ECM. 16 Pin H1-1104

EC-HARNESS2 Wiring Harness Power to Motor. 5 Pin H1-1101

EC-HARNESS3 0-10 VDC wiring harness, 2 Pin H1-1921

EC-HARNESS4 0-10 VDC wiring harness, 4 Pin, 2W H1-1921A

0-10 VDC wiring harness, 4 Pin, 4W H1-1921H

Transformers

EC-TRANS120A Transformer 120V,24V,50VA H1-0692

EC-TRANS208A Transformer 208-240V,24V,50VA H1-0685

EC-TRANS277A Transformer 277V,24V,50VA H1-0674

EC-TRANS480A Transformer 480V,24V,50VA H1-0686

EC-TRANS2424 Isolation Transformer 24V,24V,50VA H1-0673

EC-TRANSB Transformer 120V/208/240/480 to

24V,75VA H1-0689

EC-TRANS277B Transformer 277V,24V,75VA H1-0677

MISC

EC-AFSW Airflow Switch H1-0236A

EC-AFSWPB Airflow Switch Probe 4" H1-0242

EC-AFSWPBL Airflow Switch Probe 6" H1-1924

EC-AUTOLMTSW Auto Temp. LMT Switch H1-0006

EC-MANLMTSW Manual Temp. LMT Switch H1-0805

EC-FANRELAY Fan Relay 24V H1-0666

ELECTRIC CONTROLS - Transformers

Code Description Part Number

V2072

V2073

V2074

V2075

V2076

120 to 24 v. 40VA - foot mount

- 4" x 4" elec. box

208/240 to 24 v. 40VA - foot mount

277 to 24 v. 40VA - foot mount

24 to 24 v. 50VA - foot mount

H1-0669

H1-0671

H1-0675

H1-0673

RAPP Code Description Part Number

BLW10x10R Blower 10x10R H1-0904X

BLW10x10T Blower 10x10T H1-0903X

BLW10x4R Blower 10x4R H1-0906X

BLW10x6R Blower 10x6R H1-0905AX

BLW11x4R Blower 11x4R H1-2427X

BLW9x4T Blower 9x4T H1-1809

BLW9x7R Blower 9x7R H1-0900X

BLW9x7T Blower 9x7T H1-0902AX

BLW9x9R Blower 9x9R H1-1983X

BLW35S1E Blower for 35S(ST) Size 1

ECM Mtr

H1-2361,

H1-2361A,

& H1-2361B

BLW35S3P Blower for 35S(ST) Size 3

PSC Mtr

H1-0900ZX

BLW37S1 Wheel-Housing for 3S(ST)

Size 1 ECM

H1-2361B

BLW37S2E Blower for 37S(ST) Size 2

ECM Mtr

H1-2902AX

BLW35N3 Blower for 35N Size 3

ECM-PSC Mtr

H1-0900ZX

BLW33S10A Blower for 33SZ Size 10

ECM LH-CW

H1-2119

BLW33S10B Blower for 33SZ Size 10

ECM RH-CCW

H1-2120

BLW38S-38F1A Blower for 38S Size 1 ECM

Mtr OL

H1-2134

BLW38S-38F1B Blower for 38S Size 1 ECM

Mtr OR

H1-2135

BLOWERS AND WHEELS

Nailor Industries, Inc. reserves the right to change any information concerning product or specification without notice or obligation.

FILTERS

Page 6 of 10 7-6-23 IOM-FPTU

Model Series Fan Powered Terminal Units Replacement Parts

Model 35S Basic Unit Top Inlet

Unit

Size RAPP Code Description Part Number

1, 2 VH1-0196 Filter 1" 14x16 H1-0196

VH1-0196A Filter 1" MERV8 14x16 H1-0196A

3VH1-0199 Filter 1" 16x16 H1-0199

VH1-1810 Filter 1" MERV8 16x16 H1-1810

4,5 VH1-0979 Filter 1" 16x25 H1-0979

Filter 1" MERV8 16x25 H1-3108

6VH1-0200 Filter 1" 18x28 H1-0200

Filter 1" MERV8 18x28 H1-0200A

7 (2) VH1-0979 Filter 1" 16x25 H1-0979

Filter 1" MERV8 16x25 H1-3108

Model 35SST Stealth

Unit

Size RAPP Code Description Part Number

1, 2 VH1-0974 Filter 1" 10x14 H1-0974

VH1-2055 Filter 1" MERV8 10x14 H1-2055

3VH1-0977 Filter 1" 12x18 H1-0977

VH1-1966A Filter 1" MERV8 12x18 H1-1966A

4VH1-0196 Filter 1" 14x16 H1-0196

VH1-0196A Filter 1" MERV8 14x16 H1-0196A

5VH1-0975 Filter 1" 14x18 H1-0975

VH1-1434A Filter 1" MERV8 14x18 H1-1434A

6VH1-0197 Filter 1" 18x19 H1-0197

VH1-0197A Filter 1" MERV8 18x19 H1-0197A

7 (2) VH1-0928 Filter 1" 14x14 H1-0928

Filter 1" MERV7 14x14 H1-1996

Model 35S Basic Unit Side Inlet & Q Boot option

Unit

Size RAPP Code Description Part Number

1, 2 VH1-0998 Filter 1" 10x12 H1-0998

VH1-0998A Filter 1" MERV8 10x12 H1-0998A

3VH1-0196 Filter 1" 14x16 H1-0196

VH1-0196A Filter 1" MERV8 14x16 H1-0196A

4,5 VH1-0199 Filter 1" 16x16 H1-0199

VH1-1810 Filter 1" MERV8 16x16 H1-1810

6VH1-1529 Filter 1" 17x18 H1-1529

VH1-1529A Filter 1" MERV8 17x18 H1-1529A

(2)

VH1-0196 Filter 1" 14x16 H1-0196

VH1-0196A Filter 1" MERV8 14x16 H1-0196A

Model 37S Basic Unit

Unit

Size RAPP Code Description Part Number

1VH1-0997 Filter 1" 8x10 H1-0997

VH1-0997A Filter 1" MERV8 8x10 H1-0997A

2,3 VH1-0203 Filter 1" 10x18 H1-0203

VH1-2056 Filter 1" MERV8 10x18 H1-2056

4 (2) VH1-0974 Filter 1" 10x14 H1-0974

VH1-2055 Filter 1" MERV8 10x14 H1-2055

Model 37SST Stealth

Unit

Size RAPP Code Description Part Number

1VH1-0201 Filter 1" 9x11 H1-0201

VH1-0201A Filter 1" MERV8 9x11 H1-0201A

2,3 VH1-0202 Filter 1" 11x12 H1-0202

VH1-2020 Filter 1" MERV8 11x12 H1-2020

4 (2) VH1-0974 Filter 1" 10x14 H1-0974

VH1-2055 Filter 1" MERV8 10x14 H1-2055

Model 35N Basic Unit & Q Boot Option

Unit

Size RAPP Code Description Part Number

2VH1-1282 Filter 1" 13x26 H1-1282

VH1-1282A Filter 1" MERV8 13x26 H1-1282A

3VH1-1283 Filter 1" 17x27 H1-1283

VH1-1283A Filter 1" MERV8 17x27 H1-1283A

5VH1-1284 Filter 1" 17x33 H1-1284

VH1-1284A Filter 1" MERV8 17x33 H1-1284A

6VH1-1285 Filter 1" 19x35 H1-1285

VH1-1285A Filter 1" MERV8 19x35 H1-1285A

Model 37N

Unit

Size RAPP Code Description Part Number

2VH1-2254A Filter 1" 11x14 H1-2254A

VH1-2255A Filter 1" MERV8 11x14 H1-2255A

3VH1-2254B Filter 1" 11x18 H1-2254B

VH1-2255B Filter 1" MERV8 11x18 H1-2255B

4VH1-2254C Filter 1" 11x21 H1-2254C

VH1-2255C Filter 1" MERV8 11x21 H1-2255C

Model Series 35SXC

Unit

Size RAPP Code Description Part Number

1Filter 1" 6x14 H1-3457

Filter 1" MERV8 6x14

3Filter 1" 6x18 H1-2901

Filter 1" MERV8 6x18

5Filter 1" 12x20 H1-2902

Filter 1" MERV8 10x20

Nailor Industries, Inc. reserves the right to change any information concerning product or specification without notice or obligation.

7-6-23 IOM-FPTU Page 7 of 10

Model 35S(ST)

Unit

Size RAPP Code Description Part Number Program

1 MTR35SECMS1 ECM Motor 35S(ST), Size 1, 120-277V H1-2267A 35S_Size1_ALL_R3

2 MTR35SECMS2 ECM Motor 35S(ST), Size 2, 120-277V H1-2267A 35S_Size2_ALL

3 MTR35SECMS3 ECM Motor 35S(ST), Size 3, 120-277V H1-2269A 35S_3ADSR

4 MTR35SECMS4 ECM Motor 35S(ST), Size 4, 120-277V H1-2269A 35S_4ADSR

5 MTR35SECMS5 ECM Motor 35S(ST), Size 5, 120-277V H1-2270A 35S_5ADSR

6 MTR35SECMS6 ECM Motor 35S(ST), Size 6, 120-277V H1-2271A 35S_6ADSR

7 MTR35SECMS7 ECM Motor 35S(ST), Size 7, 120-277V H1-2270A 35S_7ADSR

Model 35N

Unit

Size RAPP Code Description Part Number Program

2 MTR35NECMS2 ECM Motor 35N, Size 2, 120-277V H1-2267A 35N_Size2_ALL_E

3 MTR35NECMS3 ECM Motor 35N, Size 3, 120-277V H1-2267A 35N_Size3_ALL_E

5 MTR35NECMS5 ECM Motor 35N, Size 5, 120-277V H1-2270A 35N_Size5_ALL_E

6 MTR35NECMS6 ECM Motor 35N, Size 6, 120-277V H1-2270A 35N_Size6_ALL_E

Model Series 35SXC

Unit

Size RAPP Code Description Part Number Program

1 MTR35XECMS1A V4 H1-3146 35S(ST_XC)_1_120V.ECM

1 MTR35XECMS1B V5A,V5B,V6 H1-3145 35S(ST_XC)_1_277V.ECM

3 MTR35XECMS3 V4,V5A,V5B,V6 H1-3098 35SXC-3 HEB.ECM_Application

5 MTR35XECMS5 V4,V5A,V5B,V6 H1-3099 35SXC-3 HEB.ECM_Application

Model 37S(ST)

Unit

Size RAPP Code Description Part Number Program

1 MTR37SECMS1A ECM Motor 37S(ST), Size 1, 120-277V H1-2706 37S_Size1_All_R2

2 MTR37SECMS2A ECM Motor 37S(ST), Size 2, 120V H1-2706 37S_Size2_120

2 MTR37SECMS2B ECM Motor 37S(ST), Size 2, 208-277V H1-2705 37S_Size2_277

3 MTR37SECMS3 ECM Motor 37S(ST), Size 3, 120-277V H1-2269U 37S_Size3_All_R2

4 MTR37SECMS4 ECM Motor 37S(ST), Size 4, 120-277V H1-2267A 37S_Size4_All_R2

Model 37N

Unit

Size RAPP Code Description Part Number Program

2 MTR37NECMS2 ECM Motor 37N, Size 2, 120-277V H1-2267A 37N_2ADS2

3 MTR37NECMS3 ECM Motor 37N, Size 3, 120-277V H1-2267A 37N_3ADSR

4 MTR37NECMS4 ECM Motor 37N, Size 4, 120-277V H1-2269U 37N_Size4_ALL_R2

EPIC ECM MOTORS

Model Series Fan Powered Terminal Units Replacement Parts

Nailor Industries, Inc. reserves the right to change any information concerning product or specification without notice or obligation.

Model 35S(ST)

Unit Size RAPP Code Description Part Number Capacitor

1,2 MTR35SPSCS1A PSC 35S, Size 1&2, 1/10 HP, 120V+Cap H1-2584 H1-0875

1,2 MTR35SPSCS1B PSC 35S, Size 1&2, 1/10 HP, 208V+Cap H1-2585 H1-0875

1,2 MTR35SPSCS1C PSC 35S, Size 1&2, 1/10 HP, 277V+Cap H1-2586 H1-0875

3 MTR35SPSCS3A PSC 35S, Size 3, 1/4 HP, 120V+Cap H1-2590S H1-0878

3 MTR35SPSCS3B PSC 35S, Size 3, 1/4 HP, 208V+Cap H1-2591S H1-0878

3 MTR35SPSCS3C PSC 35S, Size 3, 1/4 HP, 277V+Cap H1-2592S H1-0878

4 MTR35SPSCS4A PSC 35S, Size 4, 1/3 HP, 120V+Cap H1-2593 H1-0877

4 MTR35SPSCS4B PSC 35S, Size 4, 1/3 HP, 208V+Cap H1-2594 H1-0876

4 MTR35SPSCS4C PSC 35S, Size 4, 1/3 HP, 277V+Cap H1-2595 H1-0876

5,7 MTR35SPSCS5A PSC 35S, Size 5&7, 1/2 HP, 120V+Cap H1-2596S H1-0877

5,7 MTR35SPSCS5B PSC 35S, Size 5&7, 1/2 HP, 208V+Cap H1-2597S H1-0876

57 MTR35SPSCS5C PSC 35S, Size 5&7, 1/2 HP, 277V+Cap H1-2598S H1-0876

6 MTR35SPSCS6A PSC 35S, Size 6, 3/4 HP, 120V+Cap H1-2599 H1-0877

6 MTR35SPSCS6B PSC 35S, Size 6, 3/4 HP, 208V+Cap H1-2600 H1-0877

6 MTR35SPSCS6C PSC 35S, Size 6, 3/4 HP, 277V+Cap H1-2601 H1-0877

Model 35N

Unit Size RAPP Code Description Part Number Capacitor

2 MTR35NPSCS2A PSC 35N, Size 2, 1/10 HP, 120V+Cap H1-2584 H1-0875

2 MTR35NPSCS2B PSC 35N, Size 2, 1/10 HP, 208V+Cap H1-2585 H1-0875

2 MTR35NPSCS2C PSC 35N, Size 2, 1/10 HP, 277V+Cap H1-2586 H1-0875

3 MTR35NPSCS3A PSC 35N, Size 3, 1/4 HP, 120V+Cap H1-2590S H1-0878

3 MTR35NPSCS3B PSC 35N, Size 3, 1/4 HP, 208V+Cap H1-2591S H1-0878

3 MTR35NPSCS3C PSC 35N, Size 3, 1/4 HP, 277V+Cap H1-2592S H1-0878

5 MTR35NPSCS5A PSC 35N, Size 5, 1/2 HP, 120V+Cap H1-2596S H1-0877

5 MTR35NPSCS5B PSC 35N, Size 5, 1/2 HP, 208V+Cap H1-2597S H1-0876

5 MTR35NPSCS5C PSC 35N, Size 5, 1/2 HP, 277V+Cap H1-2598S H1-0876

6 MTR35NPSCS6A PSC 35N, Size 6, 3/4 HP, 120V+Cap H1-2599 H1-0877

6 MTR35NPSCS6B PSC 35N, Size 6, 3/4 HP, 208V+Cap H1-2600 H1-0877

6 MTR35NPSCS6C PSC 35N, Size 6, 3/4 HP, 277V+Cap H1-2601 H1-0877

Model 37S(ST)

Unit Size RAPP Code Description Part Number Capacitor

2 MTR37SPSCS2A PSC 37S, Size 2, 1/6 HP, 120V+Cap H1-2589S H1-0875

2 MTR37SPSCS2B PSC 37S, Size 2, 1/6 HP, 208V+Cap H1-2588 H1-0875

2 MTR37SPSCS2C PSC 37S, Size 2, 1/6 HP, 277V+Cap H1-2587 H1-0875

3&4 MTR37SPSCS3A PSC 37S, Size 3&4, 1/4 HP, 120V+Cap H1-2590S H1-0878

3&4 MTR37SPSCS3B PSC 37S, Size 3&4, 1/4 HP, 208V+Cap H1-2591S H1-0878

3&4 MTR37SPSCS3C PSC 37S, Size 3&4, 1/4 HP, 277V+Cap H1-2592S H1-0878

Model 37N

Unit Size RAPP Code Description Part Number Capacitor

2 MTR37NPSCS2A PSC 37N, Size 2, 1/6 HP, 120V+Cap H1-2589S H1-0875

2 MTR37NPSCS2B PSC 37N, Size 2, 1/6 HP, 208V+Cap H1-2588 H1-0875

2 MTR37NPSCS2C PSC 37N, Size 2, 1/6 HP, 277V+Cap H1-2587 H1-0875

3 MTR37NPSCS3A PSC 37N, Size 3, 1/4 HP, 120V+Cap H1-2590S H1-0878

3 MTR37NPSCS3B PSC 37N, Size 3, 1/4 HP, 208V+Cap H1-2591S H1-0878

3 MTR37NPSCS3C PSC 37N, Size 3, 1/4 HP, 277V+Cap H1-2592S H1-0878

4 MTR37NPSCS4A PSC 35N, Size 4, 1/2 HP, 120V+Cap H1-2596S H1-0877

4 MTR37NPSCS4B PSC 35N, Size 4, 1/2 HP, 208V+Cap H1-2597S H1-0876

4 MTR37NPSCS4C PSC 35N, Size 4, 1/2 HP, 277V+Cap H1-2598S H1-0876

TERMINAL UNIT PARTS

FAN POWERED TERMINAL UNIT EPIC ECM MOTORS

PSC MOTORS

Model Series Fan Powered Terminal Units Replacement Parts

Page 8 of 10 7-6-23 IOM-FPTU

Nailor Industries, Inc. reserves the right to change any information concerning product or specification without notice or obligation.

7-6-23 IOM-FPTU Page 9 of 10

Model 37SW(ST)

Unit

Size RAPP Code Description Part

Number

1 V37SHWC11 HW Coil 37S 1 Row, Size 1 H1-0091

2,3 V37SHWC13 HW Coil 37S 1 Row, Size 2,3 H1-0094

4 V37SHWC14 HW Coil 37S 1 Row, Size 4 H1-0097

1 V37SHWC21 HW Coil 37S 2 Row, Size 1 H1-0092

2,3 V37SHWC23 HW Coil 37S 2 Row, Size 2,3 H1-0095

4 V37SHWC24 HW Coil 37S 2 Row, Size 4 H1-0098

1 V37SHWC31 HW Coil 37S 3 Row, Size 1 H1-0093

2, 3 V37SHWC33 HW Coil 37S 3 Row, Size 2,3 H1-0096

4 V37SHWC34 HW Coil 37S 3 Row, Size 4 H1-0099

Model 35SXCW

Model 37NW

Unit

Size RAPP Code Description Part

Number

2 V37NHWC12 HW Coil 37N 1 Row, Size 2 H1-2163

3 V37NHWC13 HW Coil 37N 1 Row, Size 3 H1-2165

4 V37NHWC14 HW Coil 37N 1 Row, Size 4 H1-2167

2 V37NHWC22 HW Coil 37N 2 Row, Size 2 H1-2164

3 V37NHWC23 HW Coil 37N 2 Row, Size 3 H1-2166

4 V37NHWC24 HW Coil 37N 2 Row, Size 4 H1-2168

Model 35SW(ST)

Unit

size RAPP code Description Part

Number

1,2 V35SHWC12 HW Coil 35S 1 Row, Size 1,2 H1-0986

3 V35SHWC13 HW Coil 35S 1 Row, Size 3 H1-0987

4,5 V35SHWC15 HW Coil 35S 1 Row, Size 4,5 H1-0988

6 V35SHWC16 HW Coil 35S 1 Row, Size 6 H1-0989

7 V35SHWC17 HW Coil 35S 1 Row, Size 7 H1-0055

1,2 V35SHWC22 HW Coil 35S 2 Row, Size 1,2 H1-0925

3 V35SHWC23 HW Coil 35S 2 Row, Size 3 H1-0926

4,5 V35SHWC25 HW Coil 35S 2 Row, Size 4,5 H1-0927

6 V35SHWC26 HW Coil 35S 2 Row, Size 6 H1-0990

7 V35SHWC27 HW Coil 35S 2 Row, Size 7 H1-0056

1,2 V35SHWC32 HW Coil 35S 3 Row, Size 1,2 H1-0942

3 V35SHWC33 HW Coil 35S 3 Row, Size 3 H1-0943

4,5 V35SHWC35 HW Coil 35S 3 Row, Size 4,5 H1-0944

6 V35SHWC36 HW Coil 35S 3 Row, Size 6 H1-0945

7 V35SHWC37 HW Coil 35S 3 Row, Size 7 H1-1038

WATER COILS

Model Series Fan Powered Terminal Units Replacement Parts

Model 35NW

Unit

Size RAPP Code Description Part

Number

2 V35NHWC12 HW Coil 35N 1 Row, Size 2 H1-1251

3 V35NHWC13 HW Coil 35N 1 Row, Size 3 H1-1254

5 V35NHWC15 HW Coil 35N 1 Row, Size 5 H1-1257A

6 V35NHWC16 HW Coil 35N 1 Row, Size 6 H1-1260

2 V35NHWC22 HW Coil 35N 2 Row, Size 2 H1-1252

3 V35NHWC23 HW Coil 35N 2 Row, Size 3 H1-1255

5 V35NHWC25 HW Coil 35N 2 Row, Size 5 H1-1258

6 V35NHWC26 HW Coil 35N 2 Row, Size 6 H1-1261

2 V35NHWC32 HW Coil 35N 3 Row, Size 2 H1-1253

3 V35NHWC33 HW Coil 35N 3 Row, Size 3 H1-1256

5 V35NHWC35 HW Coil 35N 3 Row, Size 5 H1-1259

6 V35NHWC36 HW Coil 35N 3 Row, Size 6 H1-1262

Unit

size RAPP code Description Part

Number

1 V35SHWC12 HW Coil 35S 1 Row, Size 1 H1-0986

3 V35SHWC13 HW Coil 35S 1 Row, Size 3 H1-0987

5 V35SHWC15 HW Coil 35S 1 Row, Size 5 H1-0988

1 V35SHWC22 HW Coil 35S 2 Row, Size 1 H1-0925

3 V35SHWC23 HW Coil 35S 2 Row, Size 3 H1-0926

5 V35SHWC25 HW Coil 35S 2 Row, Size 5 H1-0927

1 V35SHWC32 HW Coil 35S 3 Row, Size 1 H1-0942

3 V35SHWC33 HW Coil 35S 3 Row, Size 3 H1-0943

5 V35SHWC35 HW Coil 35S 3 Row, Size 5 H1-0944

RAPP

Code Description Part

Number

EC-FSBLK1PA Fuseblock, 1P, 250V, 30A H1-0016

EC-FSBLK1PB Fuseblock, 1P, 250V, 60A H1-0263

EC-FSBLK1PC Fuseblock, 1P, 600V, 30A H1-0973

EC-FSBLK1PD Fuseblock, 1P, 600V, 60A H1-0269A

EC-FSBLK2PA Fuseblock, 2P, 250V, 30A H1-0920

EC-FSBLK2PC Fuseblock, 2P, 600V, 30A H1-0264

EC-FSBLK2PD Fuseblock, 2P, 600V, 60A H1-0269B

EC-FSBLK3PA Fuseblock, 3P, 250V, 30A H1-0265

EC-FSBLK3PB Fuseblock, 3P, 250V, 60A H1-0266

EC-FSBLK3PC Fuseblock, 3P, 600V, 30A H1-0268

EC-FSBLK3PD Fuseblock, 3P, 600V, 60A H1-0269

EC-FUS250V15 Fuse, 250V, 15A H1-0320A

EC-FUS250V20 Fuse, 250V, 20A H1-0321A

EC-FUS250V25 Fuse, 250V, 25A H1-0322A

EC-FUS250V30 Fuse, 250V, 30A H1-0323A

EC-FUS250V35 Fuse, 250V, 35A H1-0324A

EC-FUS250V40 Fuse, 250V, 40A H1-0325A

EC-FUS250V45 Fuse, 250V, 45A H1-0326A

EC-FUS250V50 Fuse, 250V, 50A H1-0327A

EC-FUS250V60 Fuse, 250V, 60A H1-0328A

EC-FUS600V15 Fuse, 600V, 15A H1-0329A

EC-FUS600V20 Fuse, 600V, 20A H1-0330A

EC-FUS600V25 Fuse, 600V, 25A H1-0331A

EC-FUS600V30 Fuse, 600V, 30A H1-0332A

EC-FUS600V35 Fuse, 600V, 35A H1-0333A

EC-FUS600V40 Fuse, 600V, 40A H1-0334A

EC-FUS600V45 Fuse, 600V, 45A H1-0335A

EC-FUS600V50 Fuse, 600V, 50A H1-0336A

EC-FUS600V60 Fuse, 600V, 60A H1-0337A

FUSE/FUSE BLOCKS

www.nailor.com

"Complete Air Control and Distribution Solutions."

Houston, Texas

Tel: 281-590-1172

Fax: 281-590-3086

Las Vegas, Nevada

Tel: 702-648-5400

Fax: 702-638-0400

Toronto, Canada

Tel: 416-744-3300

Fax: 416-744-3360

Calgary, Canada

Tel: 403-279-8619

Fax: 403-279-5035

Page 10 of 10 7-6-23 IOM-FPTU

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Nailor Terminal tactile

Nailor

Nailor 37S Manuel utilisateur

Manuels Terminal tactile populaires d'autres marques

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manuel utilisateur

Ingenico

Ingenico AXIUM EX4000 Manuel utilisateur

Heisei Electronics

Heisei Electronics Q-POS 815 Manuel utilisateur

Amano

Amano MTX-15 Manuel utilisateur

FLOWBIRD

FLOWBIRD CWT Compact Touch Manuel utilisateur

Demco

Demco SP7 Manuel utilisateur

Lathem

Lathem PC600 Series Manuel utilisateur

Partner

Partner MF-2352 Manuel utilisateur

NCR

NCR RealPOS 7460-2 Manuel

Simrad

Simrad MS50 Instructions de montage

Unitech

Unitech MR350 MKII Guide de démarrage rapide

Jungheinrich

Jungheinrich WMT 210 Manuel utilisateur

Motorola

Motorola MTP850 Manuel utilisateur

YASKAWA

YASKAWA 62H-MDC0 Manuel utilisateur

MVG industries

MVG industries NeptuLink Manuel utilisateur

Price Industries Limited

Price Industries Limited FDC Manuel d'instructions

Honeywell

Honeywell TemaKey Manuel utilisateur

EBN

EBN BPC65-B-A16G Manuel utilisateur