Munters VX Series Manuel utilisateur

1© Munters Corporation, January 2020 QM1086r8

Instruction Manual

VX Fans with “RC”cone

Models: VX36FxCx • VX365FxCx • VX481FxCx • VX4815FxCx •

VX511FxCx • VX5115FxCx • VX512FxCx • VX5515FxCx

• VX552FxCx

Aerotech

VX Fan

with “RC” Cone

36”, 48”, 51”&

55” Fans

VX51 and VX55

VX36 and VX48

2QM1086r8

VX Fan with “RC” Cone 36”, 48”, 51”& 55” Fans

Instructions for Use and Maintenance

Thank You:

Thank you for purchasing a Munters VX Fan with “RC” Series Discharge Cone. Munters equipment is designed to

be the highest performing, highest quality equipment you can buy. With the proper installation and maintenance

it will provide many years of service.

Please Note:

To achieve maximum performance and insure long life from your Munters product it is essential that it be installed

and maintained properly. Please read all instructions carefully before beginning installation.

Warranty:

For Warranty claims information see the “Warranty Claims and Return Policy” form QM1021 available from the

Munters Corporation office at 1-800-227-2376 or by e-mail at [email protected].

Conditions and Limitations:

• Products and Systems involved in a warranty claim under the “Warranty Claims and Return Policy” shall have

been properly installed, maintained and operated under competent supervision, according to the instructions

provided by Munters Corporation.

• Malfunction or failure resulting from misuse, abuse, negligence, alteration, accident or lack of proper installation

or maintenance shall not be considered a defect under the Warranty.

3© Munters Corporation, January 2020 QM1086r8

Index

Chapters Page

1. Unpacking the Equipment 4

1.1 Parts List 4

1.2 Fan Dimensions 5

2. Installation Instructions 6-12

2.1 Install 6

2.2 PT Style Shutter 11

2.3 PZ Style Shutter 12

3. Electrical Wiring 13

4. Operation 15

5. Maintenance 16-17

6. Winterizing 18

6.1 Winterizing 18

6.2 Winter Weather Protection 18

7. Troubleshooting 19

8. Exploded View and Parts List 20-23

8.1 VX36 and VX48 20-21

8.2 VX51 and VX55 22-23

4QM1086r8

1.1 Parts List

Unpacking the Equipment 1.

[A]

[B]

[C]

[D]

Each Fan includes:

1 – Belt Drive Fan

1 – Cone

1 – Guard

1 – Shutter

1 – Hardware Package as follows:

HP1147– 36”/48”/51”/55” Fan, One Piece Cone, PT/PV Shutter

ID Qty. Cat. No. Description

[A] 12 KS2105 #14 x 1.5” Lag Screw, SS

[B] 8 KS0650 1⁄4”-20 x ⁷⁄₈” Truss Head Bolt, SS

[C] 8 KW3012 1⁄4” x 1” O.D. Flat Washer, SS

[D] 8 KN1717 1⁄4”-20 Hex Flange, Nylock Nut, SS

Before beginning installation, check the overall condition of the equipment. Remove packing materials, and examine all

components for signs of shipping damage. Any shipping damage is the customer’s responsibility and should be reported

immediately to your freight carrier. Fan is shipped complete with all accessories.

5© Munters Corporation, January 2020 QM1086r8

1.2 Fan Dimensions

Unpacking the EquipmentChapter 1

FRONT VIEWSIDE VIEW

K - Dia.

Fan Speciﬁcations:

Hertz: 60 60

Voltage: 120/240VAC or 208-240/480VAC

Phase: 1 or 3

Hertz: 50 50

Voltage: 110/208-220VAC or 190/380VAC

Phase: 1 or 3

FAN

DIA. ABC1*C2*DEF1*F2*G H I J K-Dia. WALL OPENING

(I.D., framed)

36” 67⁄8”22

7⁄8”6

7⁄8”45

3⁄4”45

3⁄4”22

7⁄8”22

7⁄8”50

5⁄8”24

1/16”8” --50

3⁄8” 43”W 43”H

48” 87⁄8”28

7⁄8”8

7⁄8”57

3⁄4”57

3⁄4”28

7⁄8”28

7⁄8”55

3⁄8”24

7/16”8” --63

5⁄8” 55”W 55”H

51" 7" 291⁄2"7

1⁄2"8" 60

1⁄2" 59" 301⁄4"26

1⁄2"54

3⁄16"23

3⁄16" 11" 25⁄16" 65" 561⁄2”W 573⁄4”H

55" 73⁄8"31

3⁄8"7

3⁄4"7

3⁄4"63

5⁄8"62

3⁄4"27

7⁄8"31

7⁄8"58

9⁄16"25

15⁄16"11

3⁄4"2

5⁄16" 70" 60”W 611⁄4”H

*Dimensional Plus/Minus 1/4”, Field Verify

6QM1086r8

Installation Instructions 2.

2.1 Install

Top of Post Wall

H. (See Chart A)

(See Chart A)

6 x 6 Post - 6'O.C.

Figure 1B

POST Construction

Figure 1A

Frame Construction

Ceiling

Framing

H. (See Chart A) 12"

(See Chart A)

'Z'

Chart A

'Z'

FAN DIA. CONE WALL OPENING

(W. X H.) MINIMUM SPACING 'Z' CENTER TO CENTER

DIMENSION

36” 36RC 43”W. x 43”H. 12” recommended; 8” minimum 51” Minimum

48” 48RC 55”W. x 55”H. 12” recommended; 9” minimum 64” Minimum

51”51RC 561⁄4”W. x 573⁄4”H.12”recommended; 10”minimum 66”Minimum

55”55RC 60”W. x 611⁄4”H. 12”recommended; 10”minimum 70” Minimum

Step 1

Construct the framed opening to correct size according to the Chart A.

See Figure 1A and 1B.

7© Munters Corporation, January 2020 QM1086r8

Step 2A

Insert fan into the framed opening from the inside. While lifting fan up tight to framing, fasten top of

fan with (3) Lag Screw [A].

See Figure 2A and 2B

.Next, fasten bottom of fan, then both sides with

remaining (9) Lag Screw [A]. Install flashing around opening tight to fan and caulk around fan to seal.

Installation InstructionsChapter 2

Figure 3

Wall Framing

2" Minimum Framing for fan, Bottom

Wall Opening (See Chart A, Page 4)

4" Minimum Framing for fan,

Top and Sides

Wall Framing

Figure 2A

Frame Construction

OUTSIDE INSIDE

2 x 4 Framing

#14 x 1.5" Lag Screws [A] #14 x 1.5" Lag Screws [A]

Post

2 x 8 Banner Boards

2 x 8 Header Boards

Figure 2B

Post Construction

INSIDEOUTSIDE

Step 2B

If fan needs to be mounted, so that shutter does not stick into building then frame fan as shown in Figure 3. Top

and sides require 4" minimum and bottom requires 2" minimum.

8QM1086r8

Installation InstructionsChapter 2

Step 3

Installing the one piece cone may require 2 people. If temperature is above 50°F then proceed to Step 5.

If temperature is below 50°F then proceed to Step 4.

Step 4

Using Locking Sheet Metal Pliers bend the cone tabs outward to allow the cone to slide onto the fan easier.

See Figure 4.

Figure 5A Figure 5B

Figure 4

Cone Tabs

Cone

Locking Sheet Metal Pliers

Cone Tab

Hole at 10 O'clock

Top Cone Tab

Cone Flange Nut [D]

Cone (outside)

Fan Outlet

(inside)

Truss Head Bolt [B]

Washer [C]

Step 5

Look for the “TOP” label on the Polycone and set the top of the Polycone on top of the fan orifice and install

(2) Truss Head Bolts [B] through holes in fan outlet through the slots in the cone at about the 10 and 2

o’clock positions and fasten with Washers [C] and Flange Nuts [D]. Truss head of each bolt must be on

the inside of the fan outlet; washers and flange nuts must be on outside of cone.

See Figure 5A and 5B.

Finger tighten nuts only at this time.

9© Munters Corporation, January 2020 QM1086r8

Note:

If installing your existing guard in the new

Polycone, then proceed to Step 9. If installing

the new snap-in guard then proceed to Step 7.

Installation InstructionsChapter 2

Figure 6

Remaining Holes

Cone

Step 6

Work down the sides of the cone, sliding the cone tabs onto the fan until the bottom tab is in place. Keep

pressure on the cone to make sure tabs stay on the fan. Install (6) Truss Head Bolts [B], Washers [C] and

Flange Nuts [D] in the remaining holes in the fan outlet and slots in the cone to finish securing cone to fan.

See Figure 5B and Figure 6.

Tighten all nuts at this time, making sure not to over tighten.

Figure 7A

Step 7

The snap-in guard has a slight conical shape to it so, when installed the center of the guard should protrude

out slightly.

See Figure 7A.

Cone Guard

10 QM1086r8

Step 8

Starting at the bottom of the cone, locate one of the guard tabs and put the guard tab through the guard slot in

the cone.

See Figure 7B

.Then work up around the guard and install each of the other guard tabs in each of

the corresponding guard slots. Some force may be required to snap the last tab into the last slot, pull out on

the center of the cone while pushing in on the guard tab until it snaps into place.

Figure 7B

Cone

Guard

Guard Tab

Guard Slot in cone

Figure 8B

Guard Mounting

Pad

Guard

eyelet

Figure 8A

Nut

Bolt

Guard Mounting Pad

Guard

Fan Outlet

Installation InstructionsChapter 2

Step 9

If installing your existing guard into the new cone, locate the flat guard mounting pads on the cone and drill

a 9⁄32” dia. hole in the center of each pad. Then insert existing guard into cone with the guard eyelets facing

away from you. Line up each eyelet with a hole in the guard pads. Secure guard to cone using (8) existing

Bolts and Nuts.

See Figure 8A and 8B

.Tighten all nuts at this time.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Munters Ventilateur

Munters

Munters EC52 Manuel d'instructions

Munters

Munters EDHE Series Manuel d'instructions

Munters

Munters EDC24HE Manuel d'instructions

Munters

Munters MFS36 Manuel d'instructions

Munters

Munters Aerotech VX36DFCP-H Series Manuel utilisateur

Munters

Munters EDC GHp Series Manuel d'instructions

Munters

Munters WM54K Manuel utilisateur

Munters

Munters WM54 Manuel d'instructions

Munters

Munters EM52 Manuel d'instructions

Munters

Munters WM54K Manuel utilisateur

Munters

Munters WM54F Manuel d'instructions

Munters

Munters RF-VX36-H Series Manuel utilisateur

Munters

Munters CX24 Manuel utilisateur

Munters

Munters EDC Series Manuel d'instructions

Munters

Munters EC52 Manuel utilisateur

Munters

Munters AT14F Manuel utilisateur

Munters

Munters WM36F Manuel utilisateur

Munters

Munters WF50 Series Manuel utilisateur

Munters

Munters Aerotech VX36DF Series Manuel utilisateur

Munters

Munters WF50 Series Manuel utilisateur

Munters

Munters Vortex VX26F1CR Manuel utilisateur

Munters

Munters WS55 Manuel utilisateur

Munters

Munters VX55 Manuel utilisateur

Munters

Munters EM36 Manuel d'instructions

Manuels Ventilateur populaires d'autres marques

ELTA FANS

ELTA FANS H03VV-F Manuel utilisateur

Hunter

Hunter 20714 Manuel d'instructions

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuel utilisateur

Hunter

Hunter Caraway Manuel d'instructions

Panasonic

Panasonic FV-15NLFS1 Manuel utilisateur

Kompernass

Kompernass KH 1150 Manuel utilisateur

VES

VES FALA100/12V/TR Manuel utilisateur

Vertiv

Vertiv Liebert DCD Manuel utilisateur

Westinghouse

Westinghouse GFP Series Manuel utilisateur

Venmar

Venmar KUBIX HRV PLUS Series Manuel utilisateur

Maico

Maico ECR 31 Manuel utilisateur

Sonnenkonig

Sonnenkonig Dinky Manuel utilisateur

S&P

S&P ECOWATT HXBR Manuel utilisateur

Wider

Wider IMP03369BH Manuel utilisateur

Panasonic

Panasonic F-60DHN Manuel utilisateur

Hinkley

Hinkley HIGHLAND Manuel utilisateur

Broan

Broan 766BN Manuel utilisateur

Premium

Premium PFS16022 Instructions de montage