Munters Aerotech VX36DF Series Manuel utilisateur

1© Munters Corporation, August 2018 QM1227r6

Instruction Manual

VX36 and VX48 with Munters Drive

36” and 48” Exhaust Fan

Models: VX36DFxxCP-Hx • VX48DFxxCP-Hx

Aerotech

VX36 & VX48

with RC cone and

Munters Drive*

*Patents Pending

2QM1227r6

VX36 and VX48 Fans

with RC Cone and Munters Drive

Instructions for Use and Maintenance

Thank You:

Thank you for purchasing an Aerotech VX36 and VX48 with Munters Drive fan. Munters equipment is

designed to be the highest performing, highest quality equipment you can buy. With the proper installation and

maintenance it will provide many years of service.

Please Note:

To achieve maximum performance and insure long life from your Munters product it is essential that it be installed

and maintained properly. Please read all instructions carefully before beginning installation.

Warranty:

For Warranty claims information see the “Warranty Claims and Return Policy” form QM1021 available from the

Munters Corporation office at 1-800-227-2376 or by e-mail at [email protected].

Conditions and Limitations:

• Products and Systems involved in a warranty claim under the “Warranty Claims and Return Policy” shall have

been properly installed, maintained and operated under competent supervision, according to the instructions

provided by Munters Corporation.

• Malfunction or failure resulting from misuse, abuse, negligence, alteration, accident or lack of proper installation

or maintenance shall not be considered a defect under the Warranty.

3© Munters Corporation, August 2018 QM1227r6

Index

Chapters Page

1. Unpacking the Equipment 4

1.1 Parts List 4

1.2 Fan Speciﬁcations 4

2. Installation Instructions 5

2.1 Fan Installation 5

2.2 PT Style Shutter 10

2.3 PZ Style Shutter 11

3. Electrical Wiring 11

3.1 Recommended Wire Routing 12

3.2 Electrical Wiring 13

3.3 Recommended Wiring 14

4. Operation and Maintenance 20

4.1 Operation 20

4.2 Maintenance 20

5. Troubleshooting 21

6. Winterizing 22

6.1 Winterizing 22

6.2 Winter Weather Protection 22

7. Exploded View and Parts List 23-24

4QM1227r6

Unpacking the Equipment 1.

1.1 Parts List

Each Fan includes:

1 - Munters Drive Fan

1 - Cone

1 - Guard

1 - Shutter

1 - Hardware Package (HP1167)

[A]

[B]

[C]

[D]

K - Dia.

FAN

DIA. ABC1*C2*DEF1*F2*G H I J K-Dia. WALL OPENING

(I.D., framed)

36” 67⁄8”22

7⁄6”6

7⁄8”6

7⁄8”45

3⁄4”45

3⁄4”22

7⁄8”22

7⁄8”50

5⁄8”24

1⁄16”8” -- 50

3⁄8” 43” W 43”H

48” 87⁄8”28

7⁄8”8

7⁄8”57

3⁄4”57

3⁄4”28

7⁄8”28

7⁄8”55

3⁄8”24

7/16”8”2

5⁄16”63

5⁄8” 55”W 55”H

*Dimensions plus/minus 1⁄4”, ﬁeld verify.

Fan Specifications: 60Hz shown (50Hz available)

Power: 230 VAC or 230/460 VAC

Phase: 1 or 3

HP1167 – 36”/48” Fan, One Piece Cone

ID Qty. Cat. No. Description

[A] 12 KS2105 #14 x 1.5” Lag Screw, SS

[B] 8 KS0650 1⁄4”-20 x 7⁄8” Truss Head Bolt, SS

[C] 8 KW3012 1⁄4” x 1” O.D. Flat Washer, SS

[D] 8 KN1717 1⁄4”-20 Hex Flange, Nylock Nut, SS

1.2 Fan Dimensions:

5© Munters Corporation, August 2018 QM1227r6

Installation Instructions 2.

2.1 Fan Installation

Step 1

Construct the framed opening to correct size according to the Chart A. See Figure 1A and 1B.

FAN DIA. CONE WALL OPENING

(W. X H.) MINIMUM SPACING 'Z' CENTER TO CENTER

DIMENSION

36” 36RC 43” W. x 43” H. 12” recommended; 8”minimum 51” Minimum

48” 48RC 55” W. x 55” H. 12” recommended; 9” minimum 64” Minimum

Chart A

Figure 1B Post Construction

Figure 1A Frame Construction

Ceiling

Framing

(See chart A) 12"

(See chart A)

See minimum

spacing notes in

Chart A Z

Top of Post Wall

(See Chart A)

6 x 6 Post - 6'O.C.

'Z'

6QM1227r6

Figure 3

Wall Framing

2" Minimum Framing for fan, Bottom

WallOpening (See Chart A, Page 4)

4" Minimum Framing for fan,

Top and Sides

Wall Framing

Step 2B

If fan needs to be mounted, so that shutter does not stick into building then frame fan as shown in

Figure 3

Top and sides require 4" minimum and bottom requires 2" minimum.

Step 2A

Insert fan into the framed opening from the inside. While lifting fan up tight to framing, fasten top of

fan with (3) Lag Screw [A].

See Figure 2A and 2B

.Next, fasten bottom of fan, then both sides with

remaining (9) Lag Screw [A]. Install flashing around opening tight to fan and caulk around fan to seal.

Figure 2A - Frame Construction

OUTSIDE INSIDE

2 x 4 Framing

#14 x 1.5" Lag Screws [A]

OUTSIDE INSIDE

Figure 2B - Frame Construction

Post

2 x 8 Banner Boards

2 x 8 Header Boards

Installation InstructionsChapter 2

7© Munters Corporation, August 2018 QM1227r6

Step 3

Installing the one piece cone may require 2 people. If temperature is above 50°F then proceed to

Step 5.

If temperature is below 50°F then proceed to

Step 4.

Step 4

Using Locking Sheet Metal Pliers bend the cone tabs outward to allow the cone to slide onto the fan easier.

See Figure 4.

Figure 4

Cone Tabs

Cone

Locking Sheet Metal Pliers

Cone Tab

Installation InstructionsChapter 2

Figure 5A

Figure 5B

Hole at 10 O'clock

Top Cone Tab

Cone Flange Nut [D]

36/48RC Cone

(outside)

Fan Outlet

(inside)

Truss Head Bolt [B]

Washer [C]

Step 5

Look for the “TOP” label on the Polycone and set the top of the Polycone on top of the fan orifice and

install (2) Truss Head Bolts [B] through holes in fan outlet through the slots in the cone at about the

10 and 2 o’clock positions and fasten with Washers [C] and Flange Nuts [D]. Truss head of each

bolt must be on the inside of the fan outlet; washers and flange nuts must be on outside of cone.

See Figure 5A and 5B.

Finger tighten nuts only at this time.

8QM1227r6

Figure 6

Remaining Holes

Cone

Step 6

Work down the sides of the cone, sliding the cone tabs onto the fan until the bottom tab is in place. Keep

pressure on the cone to make sure tabs stay on the fan. Install (6) Truss Head Bolts [B], Washers [C] and

Flange Nuts [D] in the remaining holes in the fan outlet and slots in the cone to finish securing cone to fan.

See Figure 5B and Figure 6.

Tighten all nuts at this time, making sure not to over tighten.

Installation InstructionsChapter 2

Figure 7

Step 7

The snap-in guard has a slight conical shape to it so, when installed the center of the guard should

protrude out slightly.

See Figure 7.

Cone Guard

Note:

If installing your existing guard in the new

Polycone, then proceed to Step 9. If installing

the new snap-in guard then proceed to Step 7.

9© Munters Corporation, August 2018 QM1227r6

Figure 7B

Cone

Guard

Guard Tab

Guard Slot in cone

Step 8

Starting at the bottom of the cone, locate one of the guard tabs and put the guard tab through the guard

slot in the cone.

See Figure 7B

.Then work up around the guard and install each of the other guard

tabs in each of the corresponding guard slots. Some force may be required to snap the last tab into the

last slot, pull out on the center of the cone while pushing in on the guard tab until it snaps into place.

Installation InstructionsChapter 2

Figure 8B

Guard Mounting

Pad

Figure 8A

Nut

Bolt

Guard Mounting Pad

Guard

Fan Outlet

Step 9

If installing your existing guard into the new cone, locate the flat guard mounting pads on the cone and

drill a 9⁄32” dia. hole in the center of each pad. Then insert existing guard into cone with the guard eyelets

facing away from you. Line up each eyelet with a hole in the guard pads. Secure guard to cone using

(8) existing Bolts and Nuts.

See Figure 8A and 8B

.Tighten all nuts at this time.

Guard eyelet

10 QM1227r6

Installation InstructionsChapter 2

Figure 9

PT Shutter

2.2 PT Style Shutter

Fixed Bottom

Shutter Clip

Step 11

Fasten shutter in place by rotating the side and top shutter clips over the shutter flanges.

See Figure 10.

Installation is now complete, proceed to Electrical Wiring Section.

Figure 10

Note:

PT Shutter extends into room

2 5⁄16” from back of fan.

Step 10

Insert PT Shutter into fan by sliding the bottom flange of shutter into

bottom shutter clips and pressing shutter inward.

See Figure 9.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Munters Ventilateur

Munters

Munters CX24 Manuel utilisateur

Munters

Munters Vortex VX26F1CR Manuel utilisateur

Munters

Munters TU600 Manuel d'instructions

Munters

Munters EC52 Manuel utilisateur

Munters

Munters EC50 Manuel d'instructions

Munters

Munters GB Series Manuel utilisateur

Munters

Munters EM52 Manuel utilisateur

Munters

Munters EM50 Manuel d'instructions

Munters

Munters EDHE Series Manuel d'instructions

Munters

Munters WF54 T CP Series Manuel utilisateur

Munters

Munters EM36 Manuel d'instructions

Munters

Munters WF50 Series Manuel utilisateur

Munters

Munters EC52 Manuel utilisateur

Munters

Munters Euroemme FI Manuel utilisateur

Munters

Munters CX Series Manuel utilisateur

Munters

Munters EC52 Manuel d'instructions

Munters

Munters ATLAS 74 Manuel utilisateur

Munters

Munters AT14F Manuel utilisateur

Munters

Munters AX Series Manuel utilisateur

Munters

Munters Breeze Fan Manuel d'instructions

Munters

Munters EM50 Manuel utilisateur

Munters

Munters Aerotech VX36DFCP-H Series Manuel utilisateur

Munters

Munters VX55 Manuel utilisateur

Munters

Munters MFS36 Manuel d'instructions

Manuels Ventilateur populaires d'autres marques

ELTA FANS

ELTA FANS H03VV-F Manuel utilisateur

Hunter

Hunter 20714 Manuel d'instructions

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuel utilisateur

Hunter

Hunter Caraway Manuel d'instructions

Panasonic

Panasonic FV-15NLFS1 Manuel utilisateur

Kompernass

Kompernass KH 1150 Manuel utilisateur

VES

VES FALA100/12V/TR Manuel utilisateur

Vertiv

Vertiv Liebert DCD Manuel utilisateur

Westinghouse

Westinghouse GFP Series Manuel utilisateur

Venmar

Venmar KUBIX HRV PLUS Series Manuel utilisateur

Maico

Maico ECR 31 Manuel utilisateur

Sonnenkonig

Sonnenkonig Dinky Manuel utilisateur

S&P

S&P ECOWATT HXBR Manuel utilisateur

Wider

Wider IMP03369BH Manuel utilisateur

Panasonic

Panasonic F-60DHN Manuel utilisateur

Hinkley

Hinkley HIGHLAND Manuel utilisateur

Broan

Broan 766BN Manuel utilisateur

Premium

Premium PFS16022 Instructions de montage