MPS MP2663 Manuel utilisateur

User Guide

MP2663 Evaluation Kit (EVKT-MP2663)

User Guide

MP2663 Evaluation Kit (EVKT-MP2663)

MP2663 Evaluation Kit User Guide rev 1.0 MonolithicPower.com 1

3/13/2019 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.

Table of Contents

Overview...................................................................................................................................................2

Introduction ...........................................................................................................................................2

Kit Contents...........................................................................................................................................2

Features and Benefits...........................................................................................................................3

Kit Specifications...................................................................................................................................3

Section 1. Hardware Specifications..........................................................................................................4

1.1 Personal Computer Requirements..................................................................................................4

1.2 EV2663-C-00A Specifications.........................................................................................................4

1.3 EVKT-USBI2C-02 Specifications ....................................................................................................4

Section 2. Software Requirements ...........................................................................................................5

2.1 Software Installation Procedure ......................................................................................................5

Section 3. Evaluation Kit Test Set-up .......................................................................................................6

3.1 Hardware Setup ..............................................................................................................................6

3.2 Powering up the EVB......................................................................................................................6

3.3 Software Set-Up..............................................................................................................................6

3.4 Device Programming Instructions ...................................................................................................8

3.5 Troubleshooting Tips.....................................................................................................................10

Section 4. Ordering Information..............................................................................................................11

User Guide

MP2663 Evaluation Kit (EVKT-MP2663)

MP2663 Evaluation Kit User Guide rev 1.0 MonolithicPower.com 2

3/13/2019 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.

Overview

Introduction

The EVKT-MP2663 is an evaluation kit for the MP2663. This board is designed for the MP2663, which is

a highly-integrated single-cell Li-Ion/Li-Polymer battery charger with a system power-path management

function. The layout accommodates most commonly used capacitors. The default function of this board

is preset for charger mode and the charge full voltage is preset to 4.095V for 1 cell Li-Ion battery.

Kit Contents

EVKT-MP2663 kit contents (items below can be ordered separately).

Part Number

Item

Quantity

EV2663-C-00A

MP2663 evaluation board

EVKT-USBI2C-02-

BAG

Includes one USB to I2C communication interface, one USB cable,

one ribbon cable

Online resources

Includes datasheet, user guide, product brief, and GUI

Figure 1: EVKT-MP2663 Evaluation Kit Set-Up

User Guide

MP2663 Evaluation Kit (EVKT-MP2663)

MP2663 Evaluation Kit User Guide rev 1.0 MonolithicPower.com 3

3/13/2019 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.

Features and Benefits

Fully Autonomous Charger for Single-Cell Li-Ion/Li-Polymer Batteries

Complete Power-Path Management for Simultaneously Powering the System and Charging the

Battery

Battery Voltage: 3.6V - 4.545V (accuracy ±0.5%)

Charge Current: 8-535mA (accuracy ±10%)

Input Current: 85-455mA

13V Maximum Voltage for the Input Source

I2C Interface for Setting Charging Parameters and Status Reporting

Fully Integrated

Power Switches –

oa 330mΩ LDO MOSFET between IN and SYS

oa 100mΩ battery MOSFET between SYS and BATT.

No External Blocking Diode

Built-In Robust Charging Protection

Battery Temperature Monitoring

Programmable Timer

PCB Over-Temperature Protection (OTP)

Thermal Limiting Regulation On-Chip

System Reset Function

Built-In Battery Disconnection Function

All changes made in I2C mode will NOT be retained once the EVB is powered down.

Information written in OTP mode CANNOT be changed.

Adjustable features:

I2C

OTP

Battery Regulation Voltage

Fast Charge Current

Discharge Current

Pre-charge Current

Input Voltage Regulation

Input Current Limit

BATT UVLO

Charge Timer

Watchdog Timer

Thermal Regulation

Battery Regulation Voltage

Fast Charge Current

Pre-charge Current

Watchdog Timer

PCB OTP

Kit Specifications

Feature

Specification

Supply for Board

4.35V - 5.5V

Operating Input Voltage

4.35V - 5.5V

Operating Systems Supported

Windows XP, 7, and later

System Requirements

Minimum 22.2 MB free

GUI Software

MP2663 V1.0

User Guide

MP2663 Evaluation Kit (EVKT-MP2663)

MP2663 Evaluation Kit User Guide rev 1.0 MonolithicPower.com 4

3/13/2019 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.

Section 1. Hardware Specifications

1.1 Personal Computer Requirements

The following must be minimally met to use the EVKT-MP2663.

Operating System of Windows XP, 7 or later

Net Framework 4.0

PC with a minimum of one available USB port

At least 22.2 MB of free space

1.2 EV2663-C-00A Specifications

The EV2663-C-00A is an evaluation board for the MP2663. For more information, please refer to the

EV2663-C-00A datasheet.

Figure 2: EV2663-C-00A Evaluation Board

1.3 EVKT-USBI2C-02 Specifications

The EVKT-USBI2C-02 refers to the communication interface, which connects the EVB and the PC and

its supporting accessories. It provides I2C capabilities. Together with MPS Virtual Bench Pro and I2C GUI

tools, it provides a quick and easy way to evaluate the performance of MPS digital products. For more

details, refer to the EVKT-USBI2C-02 datasheet.

Figure 3: EVKT-USBI2C-02 Communication Interface

Feature

Specification

Supply for Evaluation Board

4.35V - 5.5V

Operating Input Voltage

4.35V - 5.5V

EVB Size (L X W)

6.35cm X

6.35cm

User Guide

MP2663 Evaluation Kit (EVKT-MP2663)

MP2663 Evaluation Kit User Guide rev 1.0 MonolithicPower.com 5

3/13/2019 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.

Section 2. Software Requirements

2.1 Software Installation Procedure

Programming occurs through the MPS I2C GUI. Follow the instructions below to install the software.

Note: This software can be downloaded from the MPS website:

1. Download and extract the zip package of the “I2C evaluation kit software for MP2663” to a directory

of your choice.

2. Double click the .exe file to open the set-up guide (see Figure 4).

3. Follow the prompts in the set-up guide.

4. Wait for status screen to verify that installation is complete (see Figure 5).

Figure 4: MPS I2C GUI Set-Up Guide

Figure 5: Driver Set-Up Success

User Guide

MP2663 Evaluation Kit (EVKT-MP2663)

MP2663 Evaluation Kit User Guide rev 1.0 MonolithicPower.com 6

3/13/2019 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.

Section 3. Evaluation Kit Test Set-up

3.1 Hardware Setup

The hardware must be properly configured prior to use. Follow the instructions below to set up the EVB.

1. Locate the proper wires to connect the EVB to the EVKT-USBI2C-02 communication interface.

2. Connect SCL, SDA, and GND (see Figure 6). If needed, refer to the datasheet for further clarification.

Figure 6: EVB to MPS I2C Communication Interface Wire Connection

3.2 Powering up the EVB

1. Connect the positive and negative terminals of the load to the SYS and GND pins, respectively.

2. Connect the positive and negative terminals of the battery to the VBATT and GND pins, respectively.

If it is a battery simulator, preset the battery voltage between 0V and 4.545V, then turn it off. Connect

the battery simulator output to the VBATT and GND pins respectively.

3. Preset the power supply output between 3.9V and 7.0V, and then turn off the power supply. Connect

the positive and negative terminals of the power supply output to the VIN and GND pins, respectively.

4. Make sure the battery voltage has been preset (if a battery simulator is used, turn on the battery

emulator). Turn the power supply on. The IC will enter the power on sequence automatically.

Reminder: if the battery simulator is connected, please make sure to turn on the battery emulator first,

before the input supply in the start-up sequence.

3.3 Software Set-Up

After connecting the hardware according to Section 3.1 and Section3.2, follow the steps below to use the

GUI software:

1. Start the software. It will check the EVB connection automatically.

If connection is successful, both the USB and MP2663 DEMO board statuses are "connected".

(See Figure 7).

User Guide

MP2663 Evaluation Kit (EVKT-MP2663)

MP2663 Evaluation Kit User Guide rev 1.0 MonolithicPower.com 7

3/13/2019 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.

Figure 7: Appearance of USB and MP2663 EVB Board Show Connected

If connection is not successful, "Not Connected" will appear in red. Check connections between

the EVB, communication interface, and PC. Re-plug the USB into the computer.

1) MP2663 DEMO Board “Not Connected" means that the evaluation board is not connected

correctly.

2) USB “Not Connected" means that the USB I2C communication interface is not connected

correctly.

2. Click the “Read All Register” button to read the I2C register values and the default values are

displayed (see Figure 7).

3. Find the item you want to change and select the desired value from the drop down menu.

4. Click the “Write All” button to update values. The changed information of the item will be downloaded

to the IC.

All changes made via the I2C will be restored to default values once the EVB is powered down.

User Guide

MP2663 Evaluation Kit (EVKT-MP2663)

MP2663 Evaluation Kit User Guide rev 1.0 MonolithicPower.com 8

3/13/2019 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.

3.4 Device Programming Instructions

The MP2663-xxxx is an OTP part. Follow the instructions outlined below to create and export customized

configurations.

1. Using a computer, open the MPS GUI software. Make sure you have powered on the EVB.

2. Ensure connection between the EVB and computer.

3. Select the “OTP View” in the tool bar. (see Figure 8)

Figure 8: Select OTP

4. Enter a new table (see Figure 9). You can change any parameters highlighted.

Figure 9: Parameters that can be Adjusted in OTP Mode

5. Select values from the drop-down menus. Please make sure all the parameters are populated before

selecting the EXPORT in the tool bar. Export the configuration by clicking EXPORT. (See Figure 10).

User Guide

MP2663 Evaluation Kit (EVKT-MP2663)

MP2663 Evaluation Kit User Guide rev 1.0 MonolithicPower.com 9

3/13/2019 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.

Figure 10: Select “Export”

6. Find a location for the exported file and click “Save”. Your configurations will be saved in a .txt file

(see Figure 11).

Figure 11: Various Export Locations Available

7. Send this file to an FAE and apply for the customized "xxxx" code.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels MPS Carte mère

MPS

MPS EV6001DN-00D Manuel utilisateur

MPS

MPS EV1518DG-00A Manuel utilisateur

MPS

MPS EV3209DJ-00A Manuel utilisateur

MPS

MPS EV1477-TF-00B Manuel utilisateur

MPS

MPS EV2759-Q-00A Manuel utilisateur

MPS

MPS EV2483DQ-00C Manuel utilisateur

MPS

MPS EVKT-1203 Manuel utilisateur

MPS

MPS EV3205DJ-00A Instructions d'utilisation et d'entretien

MPS

MPS EVmEZDPD3603A-00A Manuel utilisateur

MPS

MPS EV6539B-F-00A Manuel utilisateur

MPS

MPS EV26059DQ-00B Manuel utilisateur

MPS

MPS EVKT6515 Manuel utilisateur

MPS

MPS EV2690-R-00A Manuel utilisateur

MPS

MPS EV2637A-R-00A Manuel utilisateur

MPS

MPS EV2633-R-01A Manuel utilisateur

MPS

MPS EVBL2166-D-00A Manuel utilisateur

MPS

MPS MP2696A Guide de référence

MPS

MPS EV6536-U-00A Manuel utilisateur

MPS

MPS MP2483 Manuel utilisateur

MPS

MPS MP2760 Manuel utilisateur

MPS

MPS EVHF900-P-00A Manuel utilisateur

MPS

MPS EVKT-MP8862 Manuel utilisateur

MPS

MPS EV6532-R-01A Manuel utilisateur

MPS

MPS EV0035 Manuel utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur