Moxa Technologies DA-820 Series Manuel utilisateur

P/N: 1802008200011

*1802008200011*

DA-820 Series

Quick Installation Guide

x86 Rackmount Embedded Computers

Edition 2.0, January 2018

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Overview

The DA-820’s main operating system is based on the Intel® Core™

i3/i7/Celeron CPU and QM77 chipset, and supports x86 platforms. The

DA-820 has 2 VGA connections, 6 USB ports, 4 Gigabit LAN ports, and 2

RS/232/422/485 3-in-1 serial ports, and is equipped with a 4 SATA disk

interface and default support for RAID 0/1/5/10. In addition, the DA-820

is specifically designed for substation applications that require precise

time synchronization and products meeting the IEC 61850-3 standard.

The flexible design makes the DA-820 suitable for local SCADA,

environmental monitoring, video surveillance, protocol conversion, and

PRP/HSR redundancy applications, and the cybersecurity functionality

allows you to maintain secure network communications.

Package Checklist

Each basic system model is shipped with following standard items:

•DA-820 rackmount computer

•Rackmount kit

•Quick Installation Guide

•Documentation and software CD

•Warranty card

Hardware Installation

Front View

NOTE

The power input supports two types of power supply:

HV: 100 to 240 VAC/VDC

LV: 24 to 110 VDC.

Connecting the Power

Use a screwdriver to loosen the terminal connector’s clamp screws.

Connect the power cord wires to the screws, and then retighten the

screws. The Power LED will light up to indicate that power is being

supplied to the DA-820, after which the BIOS will initialize the flash disk

module, causing the Storage LED to blink. It should take about 30 to 60

seconds for the operating system to complete the boot process.

- 3 -

Alternating Current (AC),

Single Power

Alternating Current (AC),

Dual Power

Direct Current (DC),

Single Power

Direct Current (DC),

Dual Power

Rear View

For detailed power connection and surge protection information, refer to

the DA-820 Hardware User’s Manual.

Front Panel LEDs

There are 28 LED indicators on the front panel. The LEDs are described in

the following table:

- 4 -

LED

Color

Description

Power

Green

Power is on

Off

No power input

Storage

Yellow/

Blinking

Data is being written to or read

from the storage unit

Off

Storage unit is idle

(Non-functional for

single power supply)

Off

The 1st power supply is on

Red

Error in the 2nd power supply

(Non-functional for

single power supply)

Off

The 2nd power supply is on

Red Error in the 1st power supply

Gigabit LAN LEDs

1-4

Green

100 Mbps Ethernet mode

Orange

1000 Mbps (Gigabit) Ethernet

mode

Serial Port 1/2

Green

Yellow

Programmable 1-8

Green/

Blinking

The programs 1-8 that are in

process

Connecting to a Display

The DA-820 comes with 2 VGA interfaces that use D-Sub 15-pin female

connectors.

USB Ports

The DA-820 comes with 6 USB 2.0 ports, with 4 on the rear panel and 2

on the front panel. The USB ports can be used to connect a keyboard,

mouse, or other peripherals, such as flash drives for expanding the

system’s storage capacity.

Serial Ports

The DA-820 comes with 2 software-selectable RS-232/422/485 serial

ports on the rear panel. The ports use DB9 male connectors. Refer to the

following table for pin assignments:

RS-232

RS-422

RS-485

(4-wire)

RS-485

(2-wire)

DCD

TxDA(-)

–

RxD

TxDB(+)

–

TxD

RxDB(+)

DataB(+)

DTR

RxDA(-)

DataA(-)

GND

DSR

–

RTS

–

CTS

–

- 5 -

Ethernet Ports

The DA-820 has 4 100/1000 Mbps RJ45 Ethernet ports. Refer to the

following table for pin assignments:

100 Mbps

1000 Mbps

Tx+

TRD(0)+

Tx-

TRD(0)-

Rx+

TRD(1)+

–

TRD(2)+

–

TRD(2)-

Rx-

TRD(1)-

–

TRD(3)+

–

TRD(3)-

The default IP addresses and netmasks of the Ethernet ports are shown

below. Note that the W7E models default to DHCP.

Default IP Address

Netmask

LAN 1

192.168.3.127

255.255.255.0

LAN 2

192.168.4.127

255.255.255.0

LAN 3

192.168.5.127

255.255.255.0

LAN 4

192.168.6.127

255.255.255.0

Installing Removable Storage

The DA-820 has 4 hot-swappable 2.5” SSD/HDD storage trays located on

the front panel for installing additional storage drives. Remove the screws

on the trays to install the SSD/HDD storage drives. RAID 0, 1, 5, and 10

are supported.

Configuring the Ethernet Interface

Linux Users:

To configure the network settings on your DA-820 for the first time, use

the following commands to edit the interfaces file. First, make sure all

network interfaces are offline before you reconfigure the LAN settings.

MOXA:~# ifdown –a

Next, edit the network interfaces file. The default editor on the DA-820 is

vi; however, you may use a text editor of your choice.

MOXA:~#vi /etc/network/interfaces

You may set the DA-820 for either dynamic IP addressing or static IP

addressing. For dynamic IP addressing, enter the following lines into the

network interfaces file:

# The primary network interface

auto eth0

iface eth0 inet dhcp

To configure an interface for static IP addressing, use the following

configuration. Each interface must be configured with separate entries in

the network/interfaces file; LAN1 corresponds to eth0, LAN 2 corresponds

to eth1, and so on for the remaining interfaces.

- 6 -

# The loopback network interface

auto lo

iface lo inet loopback

# The first LAN interface, LAN 1

auto eth0

iface eth0 inet static

address 192.168.3.127

netmask 255.255.255.0

broadcast 192.168.3.255

# The second LAN interface, LAN 2

auto eth1

iface eth1 inet static

address 192.168.4.127

netmask 255.255.255.0

broadcast 192.168.4.255

Exit the vi editor by typing:

:wq

After the interfaces file has been configured, use the following commands

to reinitialize the network interfaces and activate the new settings

immediately:

Moxa:~#sync; ifup –a

Windows 7 Users

Step 1:

Go to Start Control Panel Network and Internet



Network Connections.

Step 2:

On the Local Area Connection Properties screen, click

Internet Protocol (TCP/IP)

and select Properties.

Step 3:

Click OK after inputting the preferred IP address and

netmask.

Autres manuels pour DA-820 Series

Table des matières

Autres manuels Moxa Technologies Ordinateur de bureau

Moxa Technologies

Moxa Technologies UC-8410-LX Manuel utilisateur

Moxa Technologies

Moxa Technologies MC-1200 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies DA-681 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies DA-682 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies MC-5150-DC-CP Series Manuel utilisateur

Moxa Technologies

Moxa Technologies DA-660A Series Manuel utilisateur

Moxa Technologies

Moxa Technologies V2616 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies DA-682A-DPP Series Instructions d'utilisation

Moxa Technologies

Moxa Technologies IA260 series Instructions d'utilisation

Moxa Technologies

Moxa Technologies UC-2200A Series Manuel utilisateur

Moxa Technologies

Moxa Technologies MC-1100 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies BXP-A100 Series Instructions d'utilisation

Moxa Technologies

Moxa Technologies DA-681C Series Manuel utilisateur

Moxa Technologies

Moxa Technologies MPC-2121 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies V2101 series Instructions d'utilisation

Moxa Technologies

Moxa Technologies DA-820 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies MC-4510-C23 Manuel utilisateur

Moxa Technologies

Moxa Technologies UC-7402-LX Plus Manuel utilisateur

Moxa Technologies

Moxa Technologies MC-7400 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies V2416 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies DA-660-8-LX Manuel utilisateur

Moxa Technologies

Moxa Technologies V2406A Series Instructions d'utilisation

Moxa Technologies

Moxa Technologies UC-7400-CE Series Manuel utilisateur

Moxa Technologies

Moxa Technologies V2201 Manuel utilisateur

Manuels Ordinateur de bureau populaires d'autres marques

HP m9060n - Pavilion - Elite Fiche technique

Asus

Asus E210 Series Manuel utilisateur

Dell

Dell Inspiron 600m Manuel utilisateur

Dell

Dell Inspiron 3662 Manuel utilisateur

TotalFlow

TotalFlow uFLO Manuel utilisateur

HP Presario SV7000 - Desktop PC Manuel utilisateur

HP ProDesk 400 G5 Manuel

Logitech

Logitech MK320 Manuel utilisateur

Dell

Dell XPS 730 H2C Manuel utilisateur

Sony

Sony Vaio Series Manuel utilisateur

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manuel utilisateur

Alto

Alto MD 250 Manuel utilisateur

Lenovo

Lenovo ThinkCentre Edge 72 Manuel

Lenovo

Lenovo ThinkStation D20 Manuel

Arbor Technology

Arbor Technology FPC-7800 Series Manuel utilisateur

Sony

Sony VAIO VGX-TP1 Series Manuel utilisateur

Asus

Asus Eee Box B204 Manuel utilisateur

Dell

Dell Optiplex 9010 All In One Manuel utilisateur