Motorola M68EM05A24 Manuel utilisateur
MOTOROLA
SEMICONDUCTOR
USER’S MANUAL
cMOTOROLA INC., 1994; All Rights Reserved
HC05A24EMUM/D
July, 1996
HC05A24
EMULATOR MODULE
USER’S MANUAL
First Edition
Motorola reserves the right to make changes without futher notice to any products herein to
improve reliability, function, or design. Motorola does not assume any liability arising out of the
application or use of any product or circuit described herein; neither does it convey any license
under its patent rights nor the rights of others. Motorola products are not designed, intended, or
authorized for use as components in systems intended for surgical implant into the body, or other
application in which the failure of the Motorola product could create a situation where personal
injury or death may occur. Should buyer purchase or use Motorola products for any such unin-
tended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers,
employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages,
and expanses, and reasonable attorney fees arising out of, directly or indirectly, any claim of per-
sonal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola and the Motorola logo are registered trademarks of Motorola Inc.
Motorola Inc. is an Equal Opportunity/Affirmative Action Employer.
HC05A24EM USER”S MANUAL MOTOROLA
i
1
CONTENTS
CHAPTER 1 INTRODUCTION ........................................................................ 1-1
1.1 Development Systems .................................................................................. 1-1
1.1.1 Motorola Modular Development System (MMDS05) ...................... 1-1
1.1.2 M68HC05EVS Evaluation System (HC05EVS) ............................... 1-2
1.2 EM Layout ................................................................................................... 1-3
1.3 Target Connectors And Cable Information................................................... 1-4
CHAPTER 2 MMDS05 CONFIGURATION AND OPERATION .................... 2-1
2.1 Setting A24EM Jumper Headers ................................................................. 2-1
2.1.1 Reset Select Header (P4) ................................................................... 2-2
2.1.2 COP Disable Header (P5) .................................................................. 2-2
2.1.3 Clock Source Select Header (P6) ...................................................... 2-3
2.1.4 Clock Divider Header (P9) ................................................................ 2-3
2.2 Installing Personality And Help Files .......................................................... 2-4
2.2.1 Personality File .................................................................................. 2-4
2.2.2 Help File ............................................................................................ 2-4
2.3 Remaining System Installation .................................................................... 2-5
CHAPTER 3 HC05EVS CONFIGURATION AND OPERATION ................... 3-1
3.1 Setting A24EM Jumper Headers ................................................................. 3-1
3.1.1 Reset Select Header (P4) ................................................................... 3-1
3.1.2 COP Disable Header (P5) .................................................................. 3-2
3.1.3 Clock Source Select Header (P6) ...................................................... 3-3
3.1.4 Clock Divider Header (P9) ................................................................ 3-3
3.2 EVS Limitations ......................................................................................... 3-4
3.3 Logic Analyzer Connector P1 ...................................................................... 3-5
3.4 Remaining System Installation ................................................................... 3-7
HC05A24EM USER”S MANUAL
MOTOROLA
ii
1FIGURES
Figure Page
1-1 HC05A24 Emulator Module ........................................................................ 1-3
1-2 Connector P7 Pin Assignment ..................................................................... 1-4
1-3 Connector P8 Pin Assignment ..................................................................... 1-5
1-4 Target Cable and Head Assembly ................................................................ 1-7
3-1 Connector P1 Pin Assignment ..................................................................... 3-5
TABLES
Table Page
1-1 Parts required to form a target cable assemble for A24EM ......................... 1-6
3-1 Logic Analyzer Connector P1 Signal Descriptions ..................................... 3-6
HC05A24EM USER’S MANUAL MOTOROLA
1-1
1
CHAPTER 1 INTRODUCTION
This user’s manual explains connection, configuration, and operation
information specific to the M68EM05A24 Emulator Module (hereafter
referred to as A24EM). The A24EM makes possible emulation and
debugging of MC68HC705A24/MC68HC05A16 microcontroller unit
(MCU) based target systems.
The A24EM can be part of two development systems. This chapter
describes those systems and explains the layout of the A24EM.
1.1 DEVELOPMENT SYSTEMS
Your A24EM can be part of two Motorola development tools: the HC05
Motorola Modular Development System (MMDS05) or the
M68HC05EVS Evaluation System (HC05EVS).
1.1.1 Motorola Modular Development System (MMDS05)
The MMDS05 is an emulator system that provides a bus state analyzer
and real-time memory windows. The unit’s integrated design environ-
ment includes an editor, an assembler, user interface, and source-level
debug. A complete MMDS05 consists of:
•a station module -- the metal MMDS05 enclosure, containing the
control board and the internal power supply. Most system cables
connect to the MMDS05 station module. (The cable to an optional
target system, however, runs through an aperture in the station mod-
ule enclosure to connect directly to the emulator module.)
•an emulator module (EM) -- such as the A24EM: a printed circuit
board that enables system functionality for a specific MCU. The EM
fits into the station module through a sliding panel in the enclosure
top. The EM has connectors for the target cable.
•two logic clip assemblies -- twisted-pair cables that connect the sta-
tion module to your target system, a test fixture, a clock, or any other
circuitry useful for evaluation or analysis. One end of each cable
assembly has a molded connector, which fits into station module pod
A and pod B. Leads at the other end of each cable terminate in
female probe tips. Ball clips come with the cable assemblies.
•a 9-lead RS-232 serial cable -- the cable that connects the station
module to the host computer RS-232 port.
•a 9 to 25-pin adapter -- a moulded assembly that lets you connect
the 9-lead cable to a 25-pin serial port.
•system software -- software, on 3-1/2 inch diskettes.
HC05A24EM USER’S MANUAL
MOTOROLA
1-2
1•MMDS05 documentation -- an MMDS05 operations manual
(MMDS05OM/D) and the appropriate EM user’s manual.
As mentioned, your A24EM gives the MMDS05 the ability to emulate
the MC68HC705A24 and MC68HC05A16 MCUs. By substituting a
different EM, you can enable your MMDS05 to emulate an MCU of a
different series. (Your Motorola representative can explain all the EMs
available.)
Chapter 2 explains how to configure and use your A24EM as part of an
MMDS05 system. For information about MMDS05 software or the sta-
tion module, see the MMDS05 operations manual. For layout and con-
figuration information pertaining to a different EM, see the
corresponding EM user’s manual.
1.1.2 M68HC05EVS Evaluation System (HC05EVS)
An HC05EVS is an economical, two-board tool for designing, debug-
ging, and evaluating target systems based on an MC68HC05 MCU. A
complete HC05EVS consists of:
•a platform board (PFB) -- the bottom board, which supports the
emulator module. The platform board has connectors for power and
for the terminal or host computer.
•an emulator module (EM) -- such as the A24EM: a printed circuit
board that enables system functionality for a specific MCU. The EM
fits onto the PFB. The EM has connectors for a target cable and a
cable to a logic analyzer.
•an RS-232 serial cable -- the cable that connects the PFB to the host
computer RS-232 port.
•system software -- software, on 3-1/2 inch diskettes.
•HC05EVS documentation -- an HC05EVS operations manual and
the appropriate EM user’s manual.
As mentioned, your A24EM emulates the MC68HC705A24 and
MC68HC05A16 MCUs. By substituting a different EM, you can enable
your HC05EVS to emulate an MCU of a different series. (Your Motor-
ola representative can explain all the EMs available.)
Chapter 3 explains how to configure and use your A24EM as part of an
HC05EVS system. For information about HC05EVS software or the
platform board, see the HC05EVS operations manual. For layout and
configuration information pertaining to a different EM, see the corre-
sponding EM user’s manual.
HC05A24EM USER’S MANUAL MOTOROLA
1-3
1
1.2 EM LAYOUT
Figure 1-1 shows the layout of the A24EM. Jumper header P4 controls
the path of a target reset. Jumper header P5 can be used to disable the
internal COP of the MCU during software development. Jump header
P6 lets you select the clock-signal source. Jump header P9 selects the
internal oscillator clock divider.
Connectors P7 and P8, for a 56-pin SDIP cable assembly, (purchased
separately from the A24EM.) provide an interface to your target system.
If you install the A24EM in the MMDS05 station module, the target
cable passes through the slit in the station module enclosure. Connector
P1 connects to a logic analyzer. (Connector P1 has more significance for
an EVS system, as an MMDS05 system includes a bus analyzer.)
Expansion header connectors P2 and P3 connect together the EM and
the control board (for an MMDS05) or the EM and the platform board
(for an EVS).
P7 P8
P1
P2 P3
Figure 1-1. HC05A24 Emulator Module
P4
P6
P9
P5
HC05A24EM USER’S MANUAL
MOTOROLA
1-4
11.3 TARGET CONNECTORS AND CABLE INFORMATION
Figure 1-2 and 1-3 show the pin assignments for connectors P7 and P8.
For signal descriptions, consult the technical data book for the
M68HC05A24 MCU.
As connector P1 has more importance to an HC05EVS than to an
MMDS05, pin assignments for connector P1 are in Chapter 3.
To configure your A24EM for use as part of an MMDS05, follow the
instructions of Chapter 2. To configure your A24EM as part of an
HC05EVS, follow the instructions of Chapter 3.
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
PWM1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
P7
GND
/RESET
AD0
AD1
VDD
GND
GND
IRQ2
/IRQ
GND
PA5
PA4
PA2
PA0
PC6
PC4
PC2
PC0
GND
GND
GND
GND
GND
GND
GND
GND
GND
/IRQ1
PA7
PA6
GND
PA3
PA1
PC3
PC1
GND
GND
Figure 1-2. Connector P7 Pin Assignments
PC7
PC5
HC05A24EM USER’S MANUAL MOTOROLA
1-5
1
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
GND1
3
5
7
9
11
13
15
17
19
21
23
27
29
31
33
35
37
39
P8
TCAP
TCMP1
HRX
HTX
GND
HTX_CLK
PF4
PF3
PF1
PB7
PB5
PB3
PB1
GND
PE7
PE6
PE5
PE3
PE1
PE0
GND
GND
GND
HRX_CLK
PF5
GND
PF2
PF0
PB6
PB4
PB2
PB0
GND
GND
GND
PE4
PE2
GND
GND
Figure 1-3. Connector P8 Pin Assignments
25
HC05A24EM USER’S MANUAL
MOTOROLA
1-6
1To connect your A24EM to your target system via a separately pur-
chased, target cable and head assembly, follow the instructions below.
Figure 1-4 is a generic representation of a Motorola supplied target
cable assembly, which consists of a flexible cable and a SDIP target
head. Emulation of a SDIP device is achieved by fitting the SDIP target
head into the MCU socket of the target system. Table 1-1 shows the tar-
get cable and head part numbers required to form a 56-pin SDIP target
cable assembly for the A24EM.
To use a SDIP target cable, connect the large cable terminator of
M68CLB05B to M68TB05A24B56. They should be connected in such
a way that the arrow marked on the target head is pointing to the target
cable. Next, connect the small cable terminator to the A24EM target
connectors P7 and P8. The connector at the far end of the cable should
be connected to P7 and the other to P8. Plug the target head into the
MCU socket of your target system.
If you install the A24EM in the MMDS05 station module, run the target
cable through the slit in the station module enclosure.
Table 1-1. Parts required to form a target cable assembly for A24EM
Cable No. Target Head No. Notes
M68CBL05B M68TB05A24B56 56-pin SDIP cable assembly
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Motorola Matériel informatique
Motorola
Motorola MC68306 Manuel utilisateur
Motorola
Motorola DragonBall MC68328 Manuel utilisateur
Motorola
Motorola MVME712-12 Manuel utilisateur
Motorola
Motorola MMCMPFB1200 Manuel utilisateur
Motorola
Motorola ONCE SC140 Instructions d'installation et d'utilisation
Motorola
Motorola M68MPB16Z3 Manuel utilisateur
Motorola
Motorola CME-12D60 Manuel utilisateur
Motorola
Motorola MVME3600 Series Manuel utilisateur
Motorola
Motorola PowerQUICC II MPC8280 Series Manuel utilisateur
Motorola
Motorola Clearwire Manuel utilisateur
Motorola
Motorola MC68020 Manuel utilisateur
Motorola
Motorola DigitalDNA MPC180E Manuel utilisateur
Motorola
Motorola MC68VZ328 Manuel utilisateur
Motorola
Motorola 68000 Guide de configuration
Motorola
Motorola NXP SYMPHONY DSP56007 Manuel d'instructions
Motorola
Motorola MC68340 Manuel utilisateur
Motorola
Motorola PowerPC 603 Manuel utilisateur
Motorola
Motorola M68EML08EY Manuel utilisateur
Motorola
Motorola MC68341 Manuel utilisateur
Motorola
Motorola MVME5100 Series Manuel utilisateur
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
