Motorline professional MC70 Mode d’emploi

V3.0

REV. 04/2019

MC70(v1.0)

USER/INSTALLER MANUAL

A B

ENEN

STANDARDS TO FOLLOW

CONNECTION TO A WALL SWITCH WITH 2 KEYS

TECHNICAL CHARACTERISTICS

PRE-PROGRAMMING INFORMATION

PROGRAMMING

CONTROL BOARD'S RESET

SEVERAL MC70 CONTROL BOARD CONNECTIONS - MASTER FUNCTION

CONNECTION TO A WALL SWITCH WITH 1 KEY

. SAFETY INSTRUCTIONS

. CONNECTIONS SCHEME

. THE CONTROL BOARD

. PROGRAMMING

. CONTENT . SAFETY INSTRUCTIONS

INDEX

• It is important for your safety that these instructions are followed.

• Keep these instructions in a safe place for future reference.

• The ELECTROCELOS S.A. is not responsible for the improper use of the product, or other use than that for which it was

designed.

• The ELECTROCELOS S.A. is not responsible if safety standards were not taken into account when installing the

equipment, or for any deformation that may occur.

• The ELECTROCELOS S.A. is not responsible for insecurity and malfunction of the product when used with components

that were not sold by the them.

• This product was designed and manufactured strictly for the use indicated in this manual.

• This control board is not appropriate for inflammable or explosive environments.

• Any other use not expressly indicated may damage the product and/or can cause physical and property damages, and

will void the warranty.

• Do not make any changes to the automation components and/or their accessories.

• Control board for indoor use with 110V/230V connection.

• Keep remote controls away from children, to prevent the automated system from being activated involuntarily.

• The customer shall not, under any circumstances, attempt to repair or tune the automatism. Must call qualified

technician only.

• The installer must have certified professional knowledge at the level of mechanical assemblies in doors and gates

and control board programmation. He should also be able to perform electrical connections in compliance with all

applicable regulations.

• The installer should inform the customer how to handle the product in an emergency and provide him the manual.

This product is certified in accordance with European Community (EC) safety standards.

This product complies with Directive 2011/65 / EU of the European Parliament and of the Council,

of 8 June 2011, on the restriction of the use of certain hazardous substances in electrical and

electronic equipment.

(Applicable in countries with recycling systems).

This marking on the product or literature indicates that the product and electronic accessories

(eg. Charger, USB cable, electronic material, controls, etc.) should not be disposed of as other

household waste at the end of its useful life. To avoid possible harm to the environment or human

health resulting from the uncontrolled disposal of waste, separate these items from other types of

waste and recycle them responsibly to promote the sustainable reuse of material resources.Home

users should contact the dealer where they purchased this product or the Environment Agency for

details on where and how they can take these items for environmentally safe recycling. Business

users should contact their vendor and check the terms and conditions of the purchase agreement.

This product and its electronic accessories should not be mixed with other commercial waste.

This marking indicates that the product and electronic accessories (eg. charger, USB cable, electronic

material, controls, etc.) are susceptible to electric shock by direct or indirect contact with electricity. Be

cautious when handling the product and observe all safety procedures in this manual.

ATTENTION:

A B

COMAB FCH F N

MOTOR AB ABFCH FCH

PULL230V MASTER

1 2 3 4 5 6 7 8 9 10

1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10

COMAB FCH F N

MOTOR AB ABFCH FCH

PULL230V MASTER

1 2 3 4 5 6 7 8 9 10

ENEN

. CONNECTIONS SCHEME

CONNECTION TO A WALL SWITCH WITH  KEYS CONNECTION TO A WALL SWITCH WITH  KEY

Motor Motor

OPEN

OPEN ALL

CLOSE ALL

COM

"MASTER"

WALL SWITCH

 KEYS

WALL SWITCH  KEYS

WALL SWITCH

"MASTER"

WALL SWITCH

VV

All wall switches (local or master) are pressure buttons. All wall switches (local or master) are pressure buttons.

A

1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10

COMAB FCH F N

MOTOR AB ABFCH FCH

PULL230V MASTER

1 2 3 4 5 6 7 8 9 10

COMAB FCH F N

MOTOR AB ABFCH FCH

PULL230V MASTER

1 2 3 4 5 6 7 8 9 10

COMAB FCH F N

MOTOR AB ABFCH FCH

PULL230V MASTER

1 2 3 4 5 6 7 8 9 10

230V

V 230V

MC - Nº MC - Nº

OPEN

OPEN ALL

CLOSE ALL

COM

WALL SWITCH Nº WALL SWITCH Nº WALL SWITCH Nº

"OPEN"

KEY

opening line (master)

closing line (master)

common line (master) common line (master)

closing line (master)

opening line (master)

"CLOSE"

KEY

"MASTER" WALL SWITCH

MOTOR

Nº MOTOR

Nº MOTOR

Nº

OTHER MC70

MC - Nº

. CONNECTIONS SCHEME

SEVERAL MC CONTROL BOARD CONNECTIONS  MASTER FUNCTION

The MC70 control board MASTER function allows to connect and control several MC70 control boards in the same wall switch (MASTER switch). In this way, whenever a Master switch button is

pressed, all the interconnected control boards send a impulse to the motors to start the maneuver at the same time.

A B

MXSP MXSSP MX///

FALK MXSP

23mm

55mm

44mm

51mm

ENEN

. THE CONTROL BOARD . PROGRAMMING

TECHNICAL CHARACTERISTICS PRE-PROGRAMMING INFORMATION

This control board was developed to control TUB/

Rolling motors. Its small size allows it to be installed

in junction boxes, existents behind electrical switches

(push buttons). It has 2 inputs for pushbuttons

with 1 or 2 keys, one for local control and another

for centralized control, liking several MC70 control

boards on the same wall switch (Master switch).

The control board allows to be controled with

commands through 1 or 3 keys. All programming is

done at a distance, being only necessary acess to

a power supply or a wall switch to program the ﬁrst

transmitter.

• Power Supply 230V AC 50-60Hz

• Motor's output AC230V; 750W Máx

• Radio Receiver incorporated 433,92 MHz

• Working temperature -20ºC to 70ºC

• Nº of channels 15

• Code type Rolling Code

• Protection grade IP44

• Fixed maximum working time per maneuver 2min

• Dimension of box with control board 56x44x23mm

• Box material ABS

• CHARACTERISTICS BOARD

• CONNECTOR'S DESCRIPTION

CN1

01 • Motor output -Opening

02 • Motor output - Common

03 • Motor output - Closing

04 • 230V power supply (phase)

05 • 230V power supply (neutral)

06 • Wall switch connection - OPENING (NA)

07 • Wall switch connection - COMMON

08 • Wall switch connection - CLOSING (NA)

09 • Wall switch connection - MASTER - OPENING (NA)

10 • Wall switch connection - MASTER - CLOSING (NA)

Attention: The MASTER switch connects the common wire in the 07 connector

The control board allows the programming of two operating modes in transmitters: 1 key or

3 keys.

To know the keys OPEN, STOP and CLOSE of the various transmitters, check the following

schemes:

• TRANSMITTER PROGRAMMING TYPE

OPERATING MODE PERFORMANCE

1 KEY The programmed transmitter will only work with the OPEN key.

This button will send all orders to the control board.

Example: Open - Stop - Close - Stop -Open (...)

3 KEYS The programmed transmitter will work with the buttons: OPEN |

CLOSE | STOP. Each button will send a different order to the board.

OPEN

STOP

OPEN

STOP

OPEN

STOP

OPEN

STOP

OPEN

STOP

A B

5x 2x

5x8x 2x

ENEN

PROGRAMMING

The center allows the connection of pressure switches with one or two keys. To start a

maneuver, just do a simple 1 second pulse at the desired key.

2 KEYS SWITCH

It has two buttons, one for opening and one for closing.

During opening or closing maneuver, a click on the contrary key

to the motor movement will stop this maneuver.

1 KEY SWITCH

It has only one button for opening and closing.

Clicking on the button for opening/closing will stop the motor

movement.

• WALL SWITCHES

OPEN

/STOP

OPEN

/STOP

/CLOSE

This control board only allows programming MOTORLINE rolling code transmitters by a

maximum of 15 transmitters. When programming the 16th transmitter, the control board

emits 4 beeps to signal that the memory is full.

It is possible to program the ﬁrst transmitter through the control board power supply or via

a push button. When you have an already programmed transmitter, you can use it to open

the memory of the control board at distance and program new commands.

Programming new transmitter (3 keys):

• TRANSMITTER PROGRAMMING

01 • Continuously press

the OPEN key of the

transmitter you want to

program.

01 • Continuously press

the OPEN key of the

transmitter you want to

program.

02 • Connect the control

board to a 230 power

supply.

02 • Connect the control

board to a 230 power

supply.

03 • Hold the OPEN key

for 10 sec, during which

the control board emits

5 slowly beeps.

03 • Hold the OPEN key

for 10 sec, during which

the control board emits

5 slowly beeps.

04 • After 10 sec, the

control unit emits 2

quick beeps conﬁrming

conﬁrming the program

success.

04 • After 10 sec, the

control unit emits 2

quick beeps.

Do not release the

transmitter key!

. PROGRAMMING . PROGRAMMING

PRE-PROGRAMMING INFORMATION PROGRAMMING

Programming new transmitter (1 key):

05 • Hold the OPEN key

for 10 sec, during which

the control board emits

3 slowly beeps.

06 • After the total 20

sec (10 + 10), the central

emits 5 quick beeps

conﬁrming the program

success.

Programming new 3 keys transmitter through another already programmed (3 keys):

03 • Continuously

press the OPEN key

of the transmitter

you want to

program.

01 • Continuously

press the OPEN

key of an already

programmed

transmitter, for

15sec.

02 • After 15 sec,

the control board

emits 8 quick

beeps. Release the

key of the already

programmed

transmitter.

04 • Hold the

OPEN key for 10

sec, during which

the control board

emits 5 slowly

beeps.

05 • After 10 sec,

the control unit

emits 2 quick

beeps conﬁrming

the program

success.

A B

5x8x 2x

5x 5x

ENEN

. PROGRAMMING. PROGRAMMING

PROGRAMMINGPROGRAMMING

Programming new transmitter through another already programmed (3 keys):

06 • Hold the OPEN

key for more 10

sec, during which

the control board

emits 3 slowly

beeps.

06 • Hold the OPEN

key for more 10

sec, during which

the control board

emits 3 slowly

beeps.

07 • After the total

20 sec (10 + 10),

the central emits

5 quick beeps

conﬁrming the

program success.

07 • After the total

20 sec (10 + 10),

the central emits

5 quick beeps

conﬁrming the

program success.

Programming new transmitter (3keys) through a 2 buttons wall switch:

01 • Continuously

press the OPEN

and CLOSE keys of

a wall switch, for

15sec.

01 • Continuously

press the OPEN

and CLOSE keys of

a wall switch, for

15sec.

02 • After 15 sec,

the control board

emits 8 quick

beeps. Release

wall switch keys.

02 • After 15 sec,

the control board

emits 8 quick

beeps. Release

wall switch keys.

Programming new transmitter (1key) through a 2 buttons wall switch:

Programming new transmitter (3keys) through a 1 button wall switch:

01 • Continuously

press the wall

switch button, for

15sec.

02 • After 15 sec,

the control board

emits 8 quick

beeps. Release

wall switch key.

03 • Continuously

press the OPEN key

of the transmitter

you want to

program.

03 • Continuously

press the OPEN key

of the transmitter

you want to

program.

01 • Continuously

press the OPEN

key of an already

programmed

transmitter, for

15sec.

02 • After 15 sec,

the control board

emits 8 quick

beeps. Release the

key of the already

programmed

transmitter.

04 • Hold the

OPEN key for 10

sec, during which

the control board

emits 5 slowly

beeps.

04 • Hold the

OPEN key for 10

sec, during which

the control board

emits 5 slowly

beeps.

05 • After 10 sec,

the control unit

emits 2 quick

beeps.

Do not release the

transmitter key!

05 • After 10 sec,

the control unit

emits 2 quick

beeps.

Do not release the

transmitter key!

03 • Continuously

press the OPEN key

of the transmitter

you want to

program.

03 • Continuously

press the OPEN key

of the transmitter

you want to

program.

04 • Hold the

OPEN key for 10

sec, during which

the control board

emits 5 slowly

beeps.

04 • Hold the

OPEN key for 10

sec, during which

the control board

emits 5 slowly

beeps.

05 • After 10 sec,

the control unit

emits 2 quick

beeps conﬁrming

conﬁrming the

program success.

05 • After 10 sec,

the control unit

emits 2 quick

beeps conﬁrming

conﬁrming the

program success.

A B

5x8x 2x

5x 2x 5x 2x

5x 2x

ENEN

01 • Continuously

press the wall

switch button, for

15sec.

02 • After 15 sec,

the control board

emits 8 quick

beeps. Release

wall switch key.

Programming new transmitter (1key) through a 1 button wall switch:

Change motor's direction:

. PROGRAMMING. PROGRAMMING

PROGRAMMINGPROGRAMMING

Delete all transmitters through an already programmed transmitter:

Delete all transmitters through a 2 buttons wall switch:

01 • Continuously press

the OPEN and CLOSE

keys of a wall switch.

02 • Connect the control

board to a 230 power

supply.

Delete all transmitters through a 1 button wall switch:

01 • Continuously press

the wall switch button. 02 • Connect the control

board to a 230 power

supply.

03 • Continuously

press the OPEN key

of the transmitter

you want to

program.

04 • Hold the

OPEN key for 10

sec, during which

the control board

emits 5 slowly

beeps.

05 • After 10 sec,

the control unit

emits 2 quick

beeps.

Do not release the

transmitter key!

06 • Hold the OPEN

key for more 10

sec, during which

the control board

emits 3 slowly

beeps.

07 • After the total

20 sec (10 + 10),

the central emits

5 quick beeps

conﬁrming the

program success.

01 • Continuously press

the CLOSE key of an

already programmed

transmitter.

01 • Continuously press

the OPEN and CLOSE

keys of an already

programmed transmitter.

02 • Connect the control

board to a 230 power

supply.

02 • Connect the control

board to a 230 power

supply.

03 • Hold the CLOSE key

for 10 sec, during which

the control board emits

5 slowly beeps.

03 • Hold the button for

10 sec, during which the

control board emits 5

slowly beeps.

03 • Hold the OPEN and

CLOSE keys for 10 sec,

during which the control

board emits 5 slowly

beeps.

03 • Hold the OPEN and

CLOSE keys for 10 sec,

during which the control

board emits 5 slowly

beeps.

04 • After 10 sec, the

control unit emits 2

quick beeps conﬁrming

conﬁrming the program

success.

04 • After 10 sec, the

control unit emits 2

quick beeps conﬁrming

conﬁrming the program

success.

04 • After 10 sec, the

control unit emits 2

quick beeps conﬁrming

conﬁrming the program

success.

04 • After 10 sec, the

control unit emits 2

quick beeps conﬁrming

conﬁrming the program

success.

Autres manuels Motorline professional Unité de contrôle

Motorline professional

Motorline professional MCONNECT SHUTTER Manuel d'utilisation et d'entretien

Motorline professional

Motorline professional MC4 EVO Manuel utilisateur

Motorline professional

Motorline professional MC61SE Manuel d'utilisation et d'installation

Motorline professional

Motorline professional MC112N Manuel d'utilisation et d'entretien

Motorline professional

Motorline professional MC15BA Mode d’emploi

Motorline professional

Motorline professional MC7 Manuel d'utilisation et d'installation

Motorline professional

Motorline professional MC41SP Mode d’emploi

Motorline professional

Motorline professional MC61PL Manuel d'utilisation et d'installation

Motorline professional

Motorline professional MC112PR Manuel utilisateur

Motorline professional

Motorline professional MC75 Manuel d'utilisation et d'entretien

Motorline professional

Motorline professional MC70 EVO Mode d’emploi

Motorline professional

Motorline professional MC102 Mode d’emploi

Motorline professional

Motorline professional MC61BR Manuel d'utilisation et d'installation

Motorline professional

Motorline professional MC60 Manuel d'utilisation et d'entretien

Motorline professional

Motorline professional MCS01 Mode d’emploi

Motorline professional

Motorline professional MC61PL Mode d’emploi

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur