Monoprice Blackbird 24279 Manuel utilisateur

MONOPRICE

Blackbird™ 4K Fiber Optic HDMI® Extender

P/N 24279

User's Manual

SAFETY WARNINGS AND GUIDELINES

Please read this entire manual before using this device, paying extra attention to these

safety warnings and guidelines. Please keep this manual in a safe place for future reference.

This device is intended for indoor use only.

Do not expose this device to water or moisture of any kind. Do not place drinks or

other containers with moisture on or near the device. If moisture does get in or on

the device, immediately unplug it from the power outlet and allow it to fully dry

before reapplying power.

Do not touch the device, the power cord, or any other connected cables with wet

hands.

Do not expose this device to excessively high temperatures. Do not place it in, on,

or near heat sources, such as a fireplace, stove, radiator, etc. Do not leave it in direct

sunlight.

Prior to operation, check the unit and power cord for physical damage. Do not use if

physical damage has occurred.

Before plugging the unit into a power outlet, ensure that the outlet provides the

same type and level of power required by the device.

Unplug this device from the power source when not in use.

Take care to prevent damage to the power cord. Do not allow it to become

crimped, pinched, walked on, or become tangled with other cords. Ensure that the

power cord does not present a tripping hazard.

Never unplug the unit by pulling on the power cord. Always grasp the connector

head or adapter body.

Ensure that power is turned off and disconnected before making any electrical

connections.

Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or

detergents. For stubborn deposits, moisten the cloth with warm water.

This device has no user serviceable parts. Do not attempt to open, service, or

modify this device.

INTRODUCTION

Thank you for purchasing this Blackbird™ 4K Fiber Optic HDMI® Extender! This extender

allows you to transmit 4K@60Hz 4:4:4 video to distances up to 3280 feet (1000 meters)

using a single-mode fiber cable or up to 984 feet (300 meters) using a multi-mode fiber

cable. It provides up to 18Gbps bandwidth and supports bi-directional IR and RS-232

control extensions.

FEATURES

Extends HDMI® video to distances up to 3280 feet (1000 meters) using a single-

mode fiber cable or up to 984 feet (300 meters) using a multi-mode fiber cable

Fully compliant with the HDMI 2.0b and HDCP 2.2 specifications

Supports video resolutions up to 4K@60Hz 4:4:4, including 1080p@120Hz and 1080p

3D@60Hz

Provides up to 18Gbps bandwidth

Supports high-resolution, multichannel audio

Supports bi-directional wideband IR extension

Extends RS-232 control signals

CUSTOMER SERVICE

The Monoprice Customer Service department is dedicated to ensuring that your ordering,

purchasing, and delivery experience is second to none. If you have any problem with your

order, please give us an opportunity to make it right. You can contact a Monoprice

Customer Service representative through the Live Chat link on our website

www.monoprice.com during normal business hours (Mon-Fri: 5am-7pm PT, Sat-Sun: 9am-

6pm PT) or via email at [email protected]

PACKAGE CONTENTS

Please take an inventory of the package contents to ensure you have all the items listed

below. If anything is missing or damaged, please contact Monoprice Customer Service for a

replacement.

1x Fiber optical transmitter

1x Fiber optical receiver

1x Fiber transmitter module

1x Fiber receiver module

2x IR transmitters

2x IR receivers

2x AC power adapters (5 VDC, 1A)

2x 3-pin terminal blocks

4x Mounting brackets

1x User's manual

PRODUCT OVERVIEW

Transmitter

1. Power LED: The LED illuminates when power is applied.

2. Optical LED: The LED illuminates when there is a valid optical link between the

transmitter and the receiver.

3. HDMI LED: The LED illuminates when there is an active HDMI® signal.

4. DC 5V: DC barrel connector for attaching one of the included AC power adapters.

5. Optical: LC connector for attaching a single-mode or multi-mode fiber optical cable.

6. HDMI In: HDMI connector for connecting the HDMI video source device.

7. IR In: 3.5mm jack for attaching one of the included IR receivers.

8. IR Out: 3.5mm jack for attaching one of the included IR transmitters.

9. RS-232: 3-pin terminal block for connecting a device for RS-232 serial control.

10. Update: Mini USB connector for performing firmware updates.

Receiver

1. Power LED: The LED illuminates when power is applied.

2. Optical LED: The LED illuminates when there is a valid optical link between the

transmitter and the receiver.

3. HDMI LED: The LED illuminates when there is an active HDMI® signal.

4. DC 5V: DC barrel connector for attaching one of the included AC power adapters.

5. Optical: LC connector for attaching a single-mode or multi-mode optical cable.

6. HDMI Out: HDMI connector for connecting the HDMI video display.

7. IR In: 3.5mm jack for attaching one of the included IR receivers.

8. IR Out: 3.5mm jack for attaching one of the included IR transmitters.

9. RS-232: 3-pin terminal block for connecting a device for RS-232 serial control.

10. Update: Mini USB connector for performing firmware updates.

SAMPLE CONNECTION DIAGRAM

INSTALLATION

1. Ensure that all equipment to be connected is powered off and unplugged from its

power source.

2. Place or mount the transmitter and receiver in their intended locations. Use the

mounting brackets, as desired.

3. Using a High Speed HDMI® Cable (not included), plug one end into the HDMI input

on your video display, then plug the other end into the HDMI Out port on the

receiver.

4. (Optional) If you want to control the video source device from the remote location,

plug one of the included IR receivers into the IR In jack on the receiver, then

position the IR "eye" where it can receive IR signals from the remote control.

5. (Optional) If you want to control the video display from the source location, plug

one of the included IR transmitters into the IR Out jack on the receiver, then

position the IR emitter where it can transmit signals to the IR "eye" on the video

display.

6. (Optional) If you want to control a device using the serial extender feature, build a

serial cable using one of the included 3-pin terminal blocks, then plug one end into

your serial device, then plug the other end into the RS-232 connector on the

receiver.

7. Using a High Speed HDMI Cable (not included), plug one end into the HDMI In port

on the transmitter, then plug the other end into the HDMI output on your video

source device.

8. (Optional) If you want to control the video display from the source location, plug

one of the included IR receivers into the IR In jack on the transmitter, then position

the IR "eye" where it can receive IR signals from the remote control.

9. (Optional) If you want to control the video source device from the remote location,

plug one of the included IR transmitters into the IR Out jack on the transmitter, then

position the IR emitter where it can transmit signals to the IR "eye" on the video

source device.

10. (Optional) If you want to control a device using the serial extender feature, build a

serial cable using one of the included 3-pin terminal blocks, plug one end into your

serial device, then plug the other end into the RS-232 connector on the transmitter.

11. Using a single-mode or multi-mode fiber optical cable with LC connectors (not

included), plug one end into the Optical port on the receiver, then plug the other

end into the Optical port on the transmitter. Note that if this cable is to be run

inside or through the walls, it must be rated for in-wall use.

12. Plug the DC barrel connector on one of the included AC power adapters into the DC

5V connector on the receiver, then plug the adapter into a nearby AC power outlet.

13. Plug the DC barrel connector on one of the included AC power adapters into the DC

5V connector on the transmitter, then plug the adapter into a nearby AC power

outlet.

14. Plug in and power on all connected equipment. Start video playback on your source

device, then verify that the video can be seen on the remote display. If you are

using the IR extension feature, verify that you can control the video source and/or

remote display using the appropriate remote controls. If you are using the RS-232

extension feature, verify that you can control your serial device.

TECHNICAL SUPPORT

Monoprice is pleased to provide free, live, online technical support to assist you with any

questions you may have about installation, setup, troubleshooting, or product

recommendations. If you ever need assistance with your new product, please come online

to talk to one of our friendly and knowledgeable Tech Support Associates. Technical

support is available through the online chat button on our website www.monoprice.com

during regular business hours, 7 days a week. You can also get assistance through email by

sending a message to tech@monoprice.com

SPECIFICATIONS

Model

24279

Maximum Video Resolution

4K@60Hz 4:4:4, 1080p@120Hz, 1080p 3D@60Hz

Video Bandwidth

18 Gbps

Color Spaces

RGB, YCbCr 4:4:4, YCbCr 4:2:2

Color Depth

8-bit, 10-bits, or 12-bits per channel

HDMI® Version

2.0b

HDCP Version

2.2

Maximum Transmission Distance

Up to 3280 feet (1000 meters) using single-mode

fiber cable

Up to 984 feet (300 meters) using multi-mode fiber

cable

IR Frequency Range

20 ~ 60 kHz

RS-232 Baud Rate

4800 ~ 115200 bps

Input Power

5 VDC, 1A

AC Adapter Input Power

100 ~ 240 VAC, 50/60 Hz

Maximum Power Consumption

3 watts

Operating Temperature

+32 ~ +104°F (0 ~ +40°C)

Storage Temperature

-4 ~ +140°F (-20 ~ +60°C)

Operating Humidity

20 ~ 90% RH, non-condensing

Dimensions (each)

3.9" x 2.6" x 1.0" (100 x 65 x 26 mm)

Transmitter Weight

9.0 oz. (256 g)

Receiver Weight

9.2 oz. (260 g)

Certifications

CE, FCC, UL

Table des matières

Autres manuels Monoprice Extenseur

Monoprice

Monoprice 18784 Manuel utilisateur

Monoprice

Monoprice Blackbird 4K Pro HDBaseT Manuel utilisateur

Monoprice

Monoprice DVI-LH Manuel utilisateur

Monoprice

Monoprice 21792 Manuel utilisateur

Monoprice

Monoprice VGA Manuel utilisateur

Monoprice

Monoprice 34898 Manuel utilisateur

Monoprice

Monoprice 10247 Manuel utilisateur

Monoprice

Monoprice Blackbird 8159 Manuel utilisateur

Monoprice

Monoprice BLACKBIRD 44570 Manuel utilisateur

Monoprice

Monoprice 41097 Manuel utilisateur

Monoprice

Monoprice RS232-L Manuel utilisateur

Monoprice

Monoprice Blackbird 30446 Manuel utilisateur

Monoprice

Monoprice blackbird 24181 Manuel utilisateur

Monoprice

Monoprice KVM-LII Manuel utilisateur

Monoprice

Monoprice Blackbird 43959 Manuel d'utilisation

Monoprice

Monoprice Blackbird Pro WiHD 16049 Manuel utilisateur

Monoprice

Monoprice 10224 Manuel utilisateur

Monoprice

Monoprice 27841 Manuel utilisateur

Monoprice

Monoprice SE535LTD Manuel utilisateur

Monoprice

Monoprice Blackbird 27842 Manuel utilisateur

Monoprice

Monoprice 10224 Manuel utilisateur

Monoprice

Monoprice IR-320 Manuel utilisateur

Monoprice

Monoprice 21793 Manuel utilisateur

Monoprice

Monoprice Blackbird Manuel utilisateur

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

MuxLab

MuxLab 500771 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur