Monnit MonnitLink Manuel utilisateur
Monnit Wireless Sensors
and iMonnit Online Monitoring System
User Guide
Monnit Wireless Sensors
and iMonnit Online Monitoring System
User Guide
1 | M-UG01-3A | www.monnit.com | © 2011 Monnit Corp.
2 | M-UG01-3A | www.monnit.com | © 2011 Monnit Corp.
Contents
FCC Information to Users
About Monnit
System Requirements
The Monnit Wireless Hardware
MonnitLink USB Sensor Network Software Installation
MonnitLink USB Driver Installation
Monnit Gateway Application Installation
Hardware Installation (Bringing Sensors Online)
Using the iMonnit System
Logging into iMonnit.com
iMonnit User Interface (Overview)
Using “My Account” (Account and Contacts)
Selecting the Date Range
Using the Sensor List
ConguringSensors(Basic)
ConguringSensors(Advanced)
CongureMultipleSensorsSimultaneously
SettingUpNoticationsandAlerts
History and Chart Views
Exporting Data (To File)
Exporting Data to an External Source
Sensor Maps
Reports
Error Reporting, Troubleshooting and Support
Warranty Information
3
4
5
6
10
11
12
14
15
17
18
19
20
21
23
24
26
27
28
29
30
31
31
3 | M-UG01-3A | www.monnit.com | © 2011 Monnit Corp.
FCC Information to Users
This equipment has been tested and found to comply with
the limits for a Class B digital devices, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of more
of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
Warning: Changes or modications not expressly
approved by Monnit could void the user’s
authority to operate the equipment.
RF Exposure
WARNING: To satisfy FCC RF exposure requirements for mobile transmitting
devices, a separation distance of 20 cm or more should be maintained between
the antenna of this device and persons during device operation. To ensure
compliance, operations at closer than this distance are not recommended. The
antenna used for this transmitter must not be co-located in conjunction with any
other antenna or transmitter.
About Monnit Corp.
Monnit is a leader in the design and manufacture of turnkey,
self-installing, low cost wireless sensor solutions targeted at
the commercial, industrial and consumer markets. Monnit’s
sensing solutions are designed to be easily installed and
used by anyone wanting to remotely monitor information and
activities, including: access, presence of water, luminosity,
temperature, humidity, and vibration in or around structures,
machinery, and various environments.
4 | M-UG01-3A | www.monnit.com | © 2011 Monnit Corp.
Please Read Before Proceeding
THE WIRELESS SENSORS ARE ACTIVE AND HAVE ALREADY BEEN
ASSIGNED TO YOUR CUSTOMER SENSOR NETWORK. YOUR WAR-
RANTY IS INVALIDATED IF YOU DISASSEMBLE ORATTEMPT TO
DISASSEMBLE ANY OF THESE DEVICES.
5 | M-UG01-3A | www.monnit.com | © 2011 Monnit Corp.
Network and Computer Requirements
MonnitLink™USB Gateway
Computer System Requirements
To use your wireless sensors with a MonnitLink USB
Gateway you will need a Windows PC with the following:
•AMonnitLink™USB Wireless Gateway
•WindowsXPwith512MBMemory
(Windows 7 with 1024 MB Recommended)
•20MBFreeDiskSpace
•ASP.NET3.5
( http://www.asp.net/downloads/essential )
MonnitLink™Ethernet Gateway
To use your wireless sensors with a MonnitLink Ethernet
Gateway you will need the following:
•AMonnitLink™Ethernet Wireless Gateway
•An Internet enabled router with one available
Ethernet port or a direct internet ethernet
connection.
MonnitLink™Cellular Gateway
To use your wireless sensors with a MonnitLink Cellular
Gateway you will need the following:
•AMonnitLink™Cellular Wireless Gateway
•A MonnitLink™Cellular Data Plan.
Monnit Wireless Hardware
Monnit wireless sensor networks consist of MonnitLink™
Wireless Gateways, Monnit WIT™Wireless Sensors and
Monnit Sensor Monitoring Software such as iMonnit™On-
line, Monnit Express™PC Software and Monnit Enterprise™
Server Software.
The simplest way to get started with Monnit wireless sensors
is to select either a USB or Ethernet version of the gateway
and monitor your sensors online through the iMonnit Online
SensorMonitoringandNoticationSystem.
MonnitLink USB Gateways require the use of a personal
computerrunningwindowsXPorlaterandrequiresthatthe
computer remain running and connected to the internet in
able for the sensors to communicate to the online system. A
MonnitLink Ethernet Gateway is a standalone unit that oper-
ates continuously without the need for a computer and only
requires an Ethernet connection with access to the Internet.
A MonnitLink Cellular Gateway is a standalone unit that op-
erates continuously without the need for a computer and only
requires an Internet data plan available through Monnit.
6 |
M-UG01-3A | www.monnit.com | © 2011 Monnit Corp.
RF Specications
Operating Frequency 902 MHz - 928 MHz
Power Output +8 dBm
Receiver Sensitivity -102 dBm
RF Range 250 - 300 ft. non-line-of-sight
Modulation Frequency Shift Keying (FSK)
7 | M-UG01-3A | www.monnit.com | © 2011 Monnit Corp.
Rugged Plastic
Enclosure
RP SMAAntenna
Power Plug Control Button RP SMAAntenna ConnectorEthernet Port
MonnitLink™Ethernet Gateway
Indicator
Lights
This device has been designed to operate with the antennas listed below, and having a maximum gain
of 5.0 dB. Antennas not included in this list or having a gain greater than 5.0 dB are strictly prohibited for
use with this device. The required antenna impedance is 50 ohms.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen
that the equivalent isotropically radiated power (EIRP) is not more than that required for successful
communication.
Approved Antenna:
• Hyperlink HG905RD-RSP (omnidirectional)
Contains FCC ID: ZTL-RFSC1 & IC: 9794A-RFSC1
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Rugged Plastic
Enclosure
RP SMAAntenna
MonnitLink™Cellular Gateway
8 | M-UG01-3A | www.monnit.com | © 2011 Monnit Corp.
This device has been designed to operate with the antennas listed below, and having a maximum gain
of 5.0 dB. Antennas not included in this list or having a gain greater than 5.0 dB are strictly prohibited for
use with this device. The required antenna impedance is 50 ohms.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen
that the equivalent isotropically radiated power (EIRP) is not more than that required for successful
communication.
Approved Antenna:
• Hyperlink HG905RD-RSP (omnidirectional)
Contains FCC ID: ZTL-RFSC1 & IC: 9794A-RFSC1
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must accept
any interference received, including interference that may cause undesired operation.
USB Interface
Rugged Plastic
Enclosure
4” Whip Antenna
MonnitLink™USB Gateway
9 | M-UG01-3A | www.monnit.com | © 2011 Monnit Corp.
FCC ID: ZTL-RFUSB1 & IC: 9794A-RFUSB1
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This device has been designed to operate with the attached non-removable antenna.
Autres manuels pour MonnitLink
2
Table des matières
Autres manuels Monnit Porte
Monnit
Monnit Alta Cellular Gateway Series Manuel utilisateur
Monnit
Monnit MonnitLink CGW2 Manuel utilisateur
Monnit
Monnit Ethernet Gateway Series Manuel utilisateur
Monnit
Monnit ALTA Manuel utilisateur
Monnit
Monnit ALTA XL Manuel utilisateur
Monnit
Monnit Wireless Sensors and Ethernet Gateway Manuel utilisateur
Monnit
Monnit ALTA EGW4 Manuel utilisateur
Monnit
Monnit MonnitLink Manuel utilisateur
Monnit
Monnit MonnitLink Manuel utilisateur
Monnit
Monnit MNG2-9-EGW-CCE Manuel utilisateur
Manuels Porte populaires d'autres marques
LST
LST M500RFE-AS Manuel utilisateur
Kinnex
Kinnex Media Gateway Manuel utilisateur
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuel utilisateur
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur
Telsey
Telsey CPVA 500 - SIP Manuel utilisateur
