Mobil in Time MCU-010 Manuel de l'opérateur

MCU Quick Instructions Version 1.1 / 09.2018 / EN 1

MCU – Mobile Control Unit

MCU-010

Quick instructions for the operator

Read the quick instructions before beginning any work!

MCU Quick Instructions Version 1.1 / 09.2018 / EN 2

Contents

1Important notes............................................................................................................ 4

1.1 Notes to the quick instructions.............................................................................. 4

2General.......................................................................................................................... 5

3Physical components................................................................................................... 6

3.1 Safety information ................................................................................................. 6

3.2 Components on the front ...................................................................................... 7

3.3Components on the back ...................................................................................... 8

4Operation ...................................................................................................................... 9

4.1 Switching on the MCU .......................................................................................... 9

4.2 Insert SIM card (not included in scope of delivery) ................................................ 9

4.3 Unlocking the MCU ..............................................................................................10

4.4 Main menu ...........................................................................................................10

5Settings........................................................................................................................11

5.1 Display log............................................................................................................11

5.2 Change date and time ..........................................................................................13

5.3 Enter/change telephone number ..........................................................................13

5.4 Change SIM card PIN...........................................................................................14

5.5 Enter/change password .......................................................................................15

5.6 Display firmware version ......................................................................................15

5.7 Back.....................................................................................................................15

6Standard programs .....................................................................................................16

6.1 User program .......................................................................................................18

6.2 Reset all ...............................................................................................................18

7Set temperature periods.............................................................................................19

7.1 Maximum power outage time ...............................................................................19

7.2 Start user program ...............................................................................................19

7.3 Interrupt/end user program ..................................................................................20

8Error messages ...........................................................................................................22

8.1 MCU error codes..................................................................................................23

8.2 MCU status enquiry by SMS ................................................................................23

9Notes............................................................................................................................24

MCU Quick Instructions Version 1.1 / 09.2018 / EN 3

Note!

This brochure is part of the documentation for the Mobile Control Unit - MCU

is not permitted without the prior written approval of Mobil in Time Deutschland GmbH.

Legal notice

Mobil in Time Deutschland GmbH

Im Aachtal 1A

D-78267 Aach

Tel +49 7774 939 805 0

Fax +49 7774 939 805 11

www.mobilintime.com

info@mobilintime.de

MCU Quick Instructions Version 1.1 / 09.2018 / EN 4

1Important notes

1.1 Notes to the quick instructions

These quick instructions form part of the operating instructions - Mobile Electric

Heating. Read these quick instructions carefully before starting the Mobile Control Unit

(MCU).

1. Read these quick instructions.

2. Keep these quick instructions in a safe place.

3. Pay attention to all warnings.

4. Follow all instructions.

5. Under no circumstances, make changes to the device.

6. Always leave repairs to qualified personnel.

Target market:

These quick instructions are aimed at buyers, renters and operators of the Mobile

Control Unit - MCU.

Definition of terms

Mobile Control Unit - MCU

The Mobile Control Unit - MCU comprises the control system, built into the front panel

(lower portion) of the mobile electric heating.

MCU Quick Instructions Version 1.1 / 09.2018 / EN 5

2General

Thank you for choosing the MCU-010 and for your confidence in the quality of our

products that goes with it. The MCU-010 circuit board consists of hardware and

firmware and serves the purpose of automated functional heating.

The purpose of the MCU-010 circuit board is to run through heating cycles, to be

adjusted by the end-user, over a defined length of time. This reduces time and effort

considerably as it does away with the need to set heating cycles manually on site. The

following sections describe in greater detail how to start and handle the MCU-010

board.

The following symbols are used in the present manual.

NOTE:

Highlights notes with information or instructions which may help you to better

understand the device and use

it more effectively.

WARNING:

A WARNING is used to draw your attention to sources of danger that might cause

material damage, injury or even death.

MCU Quick Instructions Version 1.1 / 09.2018 / EN 6

3Physical components

In this section, the physical components of the MCU-010 are introduced one by one

and safety information provided.

3.1 Safety information

WARNING:

Before starting to set up and use the MCU

010 board for the first time, read the

important safety information, instructions for use and legal notices.

WARNING:

The MCU

-010 is not intended for use in a moist environment or in the rain.

WARNING:

Be sure to check that the electrical connections available match the required input

power of the MCU

-010. Check the polarity of the cables before connecting

them.

WARNING:

Have the electrical connections checked by an expert and pay attention to

country

-specific regulations.

WARNING:

To ensure that the protective arrangements provided by the MCU

010 are not

impaired, you may only use or install the system in accordance with the method

prescribed in this manual. No add

-ons or changes to the system are allowed.

MCU Quick Instructions Version 1.1 / 09.2018 / EN 7

3.2 Components on the front

Components

Description

1) LED green

Lights up as soon as a heating program is active.

2) LED orange

Lights up as soon as the heating is running.

3) LED blue

Blinks if reception is poor.

Lights continuously if reception is sufficient.

4) LED red

Lights up in the event of a malfunction.

5) Display

Shows the current status of the MCU.

tivated by the press of a button.

6) USB port

Connection of USB stick.

7) Reset button

Pressing this button resets the MCU.

8) Arrow keys and OK button

The buttons serve to navigate through the menu.

MCU Quick Instructions Version 1.1 / 09.2018 / EN 8

3.3 Components on the back

Components

Description

1) Metal mounting bracket

The mounting bracket is required for fitting and fixing the MCU.

2) Temperature sensor port

The temperature sensor is inserted here.

3) Programming interface

This interface is used exclusively for programming purposes.

4) SD card

The logs are stored on the SD card.

5) Antenna connection

Connection for wireless antenna.

6) SIM card slot

Slot for SIM card

7) Grounding bolt

The housing can be grounded via this bolt.

8) Fuse

Fuse for MCU

9) 6-pole socket

The power supply and the heating relay are connected here with an

option also to connect the fault alarm contact.

MCU Quick Instructions Version 1.1 / 09.2018 / EN 9

4Operation

4.1 Switching on the MCU

The MCU is automatically started via the button that turns on the electric heater.

The start-up screen appears:

23.07.2018 12:34:56

Heating program: Off

ACT: +26°C

The start-up screen will always appear automatically after 30 seconds of inactivity.

The display will turn dark after 5 minutes of inactivity.

It is reactivated by pressing any key.

4.2 Insert SIM card (not included in scope of delivery)

The message “No SIM inserted” appears in the display if no SIM card has yet been

inserted in the MCU:

23.07.2018 11:26:01

No SIM inserted

To receive status messages by SMS on a mobile phone, a valid SIM card with

existing credit must be inserted.

This is not absolutely necessary for operation of the MCU.

You can obtain a SIM card from your network provider.

There is a slot with a card holder for this purpose on the back of the MCU.

The SIM card can be released and removed by pressing the blue button with a sharp

object (pen or some such).

The mini SIM card is inserted as follows:

The display changes:

MCU Quick Instructions Version 1.1 / 09.2018 / EN 10

23.07.2018 11:34:37

SIM card has been

unlocked

The reception symbol lights up in blue.

If reception is poor, the lamp will blink.

4.3 Unlocking the MCU

The password must be entered in order to unlock the MCU. The standard password

on delivery is “1234”. The password can be modified at any time and must comprise

4 digits made up of the numbers 0 - 9.

The arrow keys and can be used to change the number.

The next number is selected via the arrow key.

23.07.2018 14:19:43

New password OK?

1234

No OK 

After entering the password, press OK to confirm.

This will automatically take you to the main menu.

4.4 Main menu

23.07.2018 11:39:34

Main menu



The arrow keys and can be used to call up the various selection settings:

Settings

Start heating program with:

standard programs

Start heating program with:

user program

Settings menu

Display log

Change date/time

Change telephone number 1

Change telephone number 2

Change telephone number 3

Change SIM card PIN

Change password

Firmware version

Back

Table des matières

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur