Mobatime Profiline Manuel utilisateur

Table des matières

Autres manuels Mobatime Horloge

Mobatime

Mobatime ECO DC series Manuel utilisateur

Mobatime

Mobatime DSC. 250.4 Manuel utilisateur

Mobatime

Mobatime METRO Manuel utilisateur

Mobatime

Mobatime ECO-M-DSC Series Manuel utilisateur

Mobatime

Mobatime MOBALine SEM 40 V2 Manuel utilisateur

Mobatime

Mobatime PROFILINE QUAD Mode d’emploi

Mobatime

Mobatime BU 190t 230 Manuel utilisateur

Mobatime

Mobatime TREND NTP Series Manuel utilisateur

Mobatime

Mobatime ECO-M-DC Series Manuel utilisateur

Mobatime

Mobatime Flex Manuel utilisateur

Mobatime

Mobatime ECO-M-DK Manuel utilisateur

Mobatime

Mobatime ECO-SLH-DC Series Manuel utilisateur

Mobatime

Mobatime SLH-DC series Manuel utilisateur

Mobatime

Mobatime METROLINE Mode d’emploi

Mobatime

Mobatime DSC Series Manuel utilisateur

Mobatime

Mobatime MOBALine TREND Manuel utilisateur

Mobatime

Mobatime MOBALINE Cristalys Date Manuel utilisateur

Mobatime

Mobatime PROFILINE Series Manuel utilisateur

Mobatime

Mobatime DMU 140 Manuel utilisateur

Mobatime

Mobatime HN 60 Manuel utilisateur

Mobatime

Mobatime SLH-DC series Manuel utilisateur

Mobatime

Mobatime PROFILINE round Mode d’emploi

Mobatime

Mobatime ECO DC series Manuel utilisateur

Mobatime

Mobatime ECO-DC Manuel utilisateur

Manuels Horloge populaires d'autres marques

Silicon Laboratories

Silicon Laboratories SI5324 Manuel utilisateur

Heathkit

Heathkit GC-1005 Manuel utilisateur

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Manuel utilisateur

Andrew O'Malley

Andrew O'Malley DOTKLOK Manuel utilisateur

ALGE-Timing

ALGE-Timing ASC3 Manuel utilisateur

Bodet

Bodet Profil 960 Manuel utilisateur

Nixie Clock

Nixie Clock Divergence Meter Manuel utilisateur

La Crosse Technology

La Crosse Technology WS-8256-AL Manuel utilisateur

Mini Gadgets

Mini Gadgets MCPro Manuel utilisateur

Casio

Casio TMR-200 Manuel utilisateur

Progetti

Progetti ILTEMPOSTRINGE Manuel

BVItech

BVItech BV-101 Manuel utilisateur

Progetti

Progetti KALIMERO Manuel

La Crosse Technology

La Crosse Technology WT-3141b Manuel

La Crosse Technology

La Crosse Technology W86531 Manuel utilisateur

Sharp

Sharp SPC900 Manuel utilisateur

La Crosse Technology

La Crosse Technology 404-50447 Manuel utilisateur

Datexx

Datexx DF0063 Manuel utilisateur

© MOBATIME 1 / 4 TE-801323.00

Exchange movements in a double-sided round Profiline clock

1. remove the modules (ring with glass and dial) from housing.

Module with hinge:

Module without hinge: Remove 4 screws from inside of the clock

© MOBATIME 2 / 4 TE-801323.00

2. Lay the ring with glass on the lower side on a table

3. Make a mark e.g. at 12:00 position on dial and housing with a pensile (to align it exactly in the

same position, when you insert the dial back to the ring.

4. then loosen the screws on bottom side of the ring.

5. try to spread the ring, until the movement and with the complete dial can be removed to the

top. The ring is quite strong, so it needs some strength to spread it.

© MOBATIME 3 / 4 TE-801323.00

6. Once the dial is out, you have to switch on the DIP switch for the 12:00 position on the NBU 190

and connect the PoE.

For SAM/SEM 100 movements, press the push button longer than 3s, when MOBALine signal is

connected

7. When it stops moving, you can loosen the screw of the hand bushing with an Allen key and

remove the minute hand.

8. The hour hand can be removed from the side with a large flat screw drive. Carefully remove it.

9. In case you have to exchange the movement, loosen the white disc nut and exchange the

movement with a new according to the description no. TE-801289 or TE-801290.

10. New movement is mounted:

Now push down again the hour hand at 12:00 position

11. Now set the minute hand carefully to 12:00 position, and fix it again with Allen key.

12. Now you have to check again the 12:00 position: remove PoE and connect it again.

When it is ok now, you can mount the dial back to ring. Be carefully that the 12:00 position of

the dial is really exactly on top

© MOBATIME 4 / 4 TE-801323.00

13. When hands positions are OK at 12:00 position, you can carefully reinsert the dial into the ring.

Please align it to the mark you have made at the beginning at the 12:00 position.

14. Push the ring together and fix it so it is completely closed

15. Repeat steps 2 to 12 with the second module

16. Mount both modules back to the housing body

17. Test the clock with the time signal