MKS 107B Manuel utilisateur
-~
ARTISAN
®
~I
TECHNOLOGY
GROUP
Your definitive source
for
quality
pre-owned
equipment.
Artisan Technology
Group
Full-service,
independent
repair
center
with
experienced
engineers
and
technicians
on staff.
We
buy
your
excess,
underutilized,
and
idle
equipment
along
with
credit
for
buybacks
and
trade-ins
.
Custom
engineering
so
your
equipment
works
exactly as
you
specify.
•
Critical
and
expedited
services
•
Leasing
/
Rentals/
Demos
• In
stock/
Ready-to-ship
•
!TAR-certified
secure
asset
solutions
Expert
team
ITrust
guarantee
I
100%
satisfaction
All
tr
ademarks,
br
a
nd
names, a
nd
br
a
nd
s a
pp
earing here
in
are
th
e property of
th
e
ir
r
es
pecti
ve
ow
ner
s.
Find the MKS Instruments 107BA at our website: Click HERE
CONTENTS
SECTION 1 GENERAL INFORMATION
1.1 Description
1.2 Specifications
SECTION 2 INSTALLATION
2.1 Unpacking and Inspection
2.2 107B Transducer Installation
2.3 Cabling and Interconnections
SECTION 3 OPERATION
3.1 General
3.2 Theory of Operation
SECTION 4 MAINTENANCE
4.1 General
4.2 Troubleshooting
i
SECTION 1
GENERAL INFORMATION
1.1 DESCRIPTION
The MKS Type 107B Transducer is the result of over twenty five years
experience with capacitance manometers and the addition of a new sensor design
(Patent Pending). This design marks the first time that six decades of
pressure measurement are available using a single capacitance manometer. When
coupled with MKS Type 116 or 146 Power Supply/Readouts, the 107B can replace
two or more pressure instruments in applications such as data logging or
process control, where environmental and process conditions are particularly
demanding. Only Inconel is exposed to the process, which permits use of
corrosive or dirty gases, and eliminates contamination of the process with
gauge materials.
Measurements are independent of gas composition; the 107B measures true
total pressure, regardless of gas species or mixtures.
The Type 107B is the first MKS transducer to be digitally linearized.
Linearization constants are stored inside EEPROM memory located in each
transducer, and thus a 107B is usable with any 116 or 146 readout.
In normal operation, the 107B Transducer heater circuit warms the sensor to
45°C for good stability and to reduce process condensation.
1-1
1.2 SPECIFICATIONS
ELECTRICAL
Power Requirements
Circuit: ±15 VDC ±5% @ 30 mA
Heater: ±15 VDC ±5% @ 300 mA OR
24 VAC ±5% @ 325 mA
Range: 1 mTorr - 1000 Torr
Accuracy: see Table 1-1*
Media Compatibility: any gas compatible with Inconel
Maximum pressure: 1800 Torr
Warmup time: 4 hours
Mechanical: see Figure 1-1
Cable length: 10 feet standard.
Environmental:
Operating ambient Temperature: 15-40°C.
Humidity: 0-95% non-condensing.
* Accuracy is the system accuracy when used with either
a 116 or 146 Power Supply/ Readout.
1-2
TABLE 1-1
Pressure Specification
1-3
Figure 1-1
Mechanical Outline 107B
1-4
SECTION 2
INSTALLATION
2.1 UNPACKING AND INSPECTION
Reasonable care has been taken to pack the Type 107B in a manner that it
reach you in perfect operating condition. However, upon receiving these units
you should check for defects, cracks, broken connectors, etc. to be certain
that damage has not occurred during shipment. If you find any damage, notify
your carrier and MKS immediately. If return of the instrument is necessary, an
Equipment Return Authorization (ERA) number is required from MKS Customer
Service to accept, expedite, repair, and return.
2.2 TYPE 107B TRANSDUCER INSTALLATION
The Type 107B comes with fitting options identical to all other 100
Series Transducers (Cajon 8 VCR, Cajon 8VCO, KF16, and
1/2" diameter tublation.) The sensor port will easily carry the weight of
the transducer. It is always suggested that chamber pressure measurement ports
be located such that the capacitance manometer is vertical with its port facing
downward. In this way process products which may appear in the sensor will
fall out into the chamber where they can be pumped, preserving the integrity of
the pressure measurement. The pressure transducer should be mounted such that
it is firmly supported and isolated from any vibration.
Note that temperature controlled transducers, such as the 107B, need a
minimum of four hours to achieve best thermal stability. After warmup, all
newly installed sensors should be zeroed. For a 107B, this means pumping the
unit to below 5x10-5 Torr and Remote Zeroing the 116 or 146 display. Refer to
the instruction manual of either unit for the appropriate procedure to follow
when remote zeroing.
The 107B/readout combination comes with MKS cable #CB107-1 or #CB107-2 which
is used between the transducer and readout.
The -1 cable is the standard 10 foot version. The -2 version
is a special cable of longer length. The connectors are male and female
type "D" and come complete with captive mounting hardware (Reference Figure 2-
1). With power off, insert connectors into their respective 107B or readout
sockets and tighten the connector screws, two on either end of the cable.
2-1
NOTE:
DUE TO THE FAILURE OF MANY USERS TO FOLLOW THE
PROPER TIGHTENING PROCEDURES FOR SINGLE OR DOUBLE
METAL FERRULE COMPRESSION TYPE VACUUM FITTINGS
AND THE RESULTING DAMAGE CAUSED TO THE PRESSURE
SENSOR, MKS DOES NOT WARRANTY THIS PRODUCT WHEN
SUCH FITTINGS ARE USED.
2.3 CABLING AND INTERCONNECTIONS
GROUNDING
Power, Analog, and Digital commons are all tied together in the power
supply; and transducer Signal common and Power common are tied together in the
transducer. Even though these commons are connected together internally, it is
important that each ground be used only for its stated purpose; otherwise
ground noise and loops can cause significant errors. These commons are
connected to chassis by a 10K ohm 1/4 W resistor, shunted by several 50 volt
capacitors totalling more than 2uF. Maximum potential difference must be
limited to avoid introducing noise.
CABLING
Since each 107B transducer comes with its own linearity correction data
stored in EEPROM memory on board, a 107B may be used with any 116 or 146
readout. The cable supplied with the 107B is a CB107-1 or CB107-2 which
requires that two screws be tightened on each end. Table 2-1 shows the
transducer cable connections.
2-2
Figure 2-1
* Heater Power: AC or DC not polarity sensitive.
TABLE 2-1
Transducer Connector
2-3
SECTION 3
OPERATION
3.1 GENERAL
The Type 107B Transducer consists of a new-technology capacitance manometer
(Patent Pending) enclosed by a heated chamber with two printed circuit (PC)
boards which provide signal conditioning, heating control and memory for
calibration constants.
3.2 THEORY OF OPERATION
SENSOR
The new sensor technology employed by the Type 107B maintains rugged
construction of previous MKS pressure transducers with their Inconel stretched
diaphragm and enclosure. A new electrode arrangement allows the transducer to
develop useful output over a six decade pressure range. Minimum resolvable
readings are 1 milliTorr and the 107B's full scale is 1000 Torr.
The variable capacitance sensor has rigidly attached electrodes located in
an evacuated chamber behind the metal diaphragm. This reference chamber is
permanently evacuated, sealed and gettered thus making the pressure measurement
totally independent of the gas type or composition.
The sensor and signal conditioning PC board are housed in a
temperature-controlled thermal chamber which is heated to 45°C. This allows the
107B to operate in many systems without effects due to condensation. Also it
improves the effective sensor and electronics temperature coefficients by at
least 30:1.
ELECTRONICS
The electronics package consists of three distinct circuits. These are (1)
the signal conditioner, (2) the heater control and (3) the calibration constant
memory circuit.
Signal conditioning is shown in the block diagram (Fig. 3-1).
A precision constant frequency oscillator is used to excite a
diode bridge arrangement. Through the bridge the excitation reaches two
capacitances, one of which is a highly stable fixed capacitor and the other is the
sensor. With the transducer held to zero pressure (high vacuum) the two
capacitances will be equal and the bridge arrangement will have zero output. (For
calibration purposes, at zero the 107B really develops between -50 millivolts and
-125 millivolts output.) As the pressure increases, the sensor capacitance will
increase and the bridge circuit will be unbalanced causing a DC voltage across the
bridge. This signal is then filtered and amplified by subsequent stages such that
at full scale pressure of 1000 Torr the output will be between 9.5 volts and 10.0
volts.
3-1
Figure 3-1
107B Block Diagram
3-2
Setting the output for a specific value is not needed since the transducer's
complete output curve is described by the data stored in EEPROM on board the
transducer. The circuitry needed to perform this task consists of a 5 volt
regulator to drop the supply +15 VDC line down to logic power levels, the
serial EEPROM memory IC, and Schmitt trigger inverters for extra noise
immunity. During calibration or power-on of a Type 116 or 146, clocking is
provided by the interfacing power supply/readout while data is either sent or
received by the EEPROM. Up to 60 pressure/voltage pairs are stored in the
memory and these are used by the readouts to construct linearization look-up
tables used in finding any given pressure.
The third circuit section is the heater control circuit, located on
the PC board which is outside of the heated shell. This circuit is a
balanced-resistor-bridge arrangement which provides analog PID control which is
optimized for this particular application. Two thermistors sense the heater
temperature and the ambient as seen by the inner enclosure to provide "lead"
and "lag" thermal signals to an integrator which controls the duty-cycle
oscillator. This oscillator will run over a large frequency range, with 33Khz
being nominal, and an enhancement
mode FET provides the heater switching.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels MKS Transducteur
MKS
MKS 523210-0-0E-T Manuel utilisateur
MKS
MKS Micro-Baratron 870B Manuel utilisateur
MKS
MKS Baratron 722C Manuel utilisateur
MKS
MKS Baratron 740C Manuel utilisateur
MKS
MKS 907 Series Manuel utilisateur
MKS
MKS 901P Comment utiliser
MKS
MKS MicroPirani 925 Series Comment utiliser
MKS
MKS Baratron 223B Manuel utilisateur
MKS
MKS Baratron 122A Series Manuel utilisateur
MKS
MKS 910-11000-0016 Manuel utilisateur
MKS
MKS Baratron 121A Manuel utilisateur
MKS
MKS Baratron 722B Manuel utilisateur
MKS
MKS Baratron 631D Manuel utilisateur
MKS
MKS UniMag 971B Fiche technique
MKS
MKS 901P Fiche technique
MKS
MKS 392 Series Manuel de l'opérateur
MKS
MKS Baratron 722A Manuel utilisateur
MKS
MKS HPS Products 999 Quattro Series Manuel utilisateur
MKS
MKS Baratron 631F Manuel utilisateur
MKS
MKS UniMag 971 Fiche technique
Manuels Transducteur populaires d'autres marques
Mianyang Weibo Electronic
Mianyang Weibo Electronic WB Series Manuel utilisateur
ProMinent
ProMinent Dulcometer DMT Manuel utilisateur
WIKA
WIKA WU-20 Manuel utilisateur
Alcatel Vacuum Technology
Alcatel Vacuum Technology BARATRON 622A Manuel utilisateur
Camille Bauer
Camille Bauer SIRAX CH-5610 Manuel utilisateur
WIKA
WIKA F2802 Manuel utilisateur
