Mitsubishi DLP XD1000U Manuel utilisateur
EN-1
LAN Control Utility
User Manual
Contents
Preparation/SetUp .........................................................................2
Preparation before using the network function...........................................2
Connection..................................................................................................2
Installation...................................................................................................3
Setting the IP address of the projector .......................................................5
When using a DHCP server ...........................................................................................6
When not using a DHCP server.....................................................................................7
Telnet setting...............................................................................................8
Setting the password (Password Setup) .......................................................................9
Setting the display language of ProjectorView (language) ............................................9
Setting the LAN control (LAN-Controlled Mode) .........................................................10
PJLink™ certification (PJLink certification Mode) .......................................................10
Save and exit ...............................................................................................................11
ProjectorView...............................................................................12
Using the ProjectorView............................................................................12
How to start up ............................................................................................................12
VIRTUAL REMOTE controller.......................................................................................14
E-mail notification function ..........................................................................................14
Initial setting.................................................................................................................15
Support for the PJLink™ function ...............................................16
EN-2
Preparation/SetUp
Preparation before using the network function
This projector is equipped with the network function to control and monitor the projector’s operations using a Web
browser and to send e-mail notification.
Before using the network function, perform the following three preparation steps.
(1) Setup of the application software “Projector-Control Device Installer”
(2) Setting of the IP address of the projector *1
(3) Setting of password, display language, LAN control, and PJLink™ certification using telnet.
*1 When setting IP addresses for multiple projectors collectively or when setting an IP address for a ceiling-
mounted projector after installation, check and take a note of combination of the projectors and the hardware
addresses (MAC addresses) in advance. To check the hardware addresses (MAC addresses), perform step 2
on the page 5.
[Major functions]
Setting of the projector’s IP address
Setting of password, display language, and LAN control
PJLink™ certification setting (Telnet function)
Startup of the controlling /supervising tool (ProjectorView) using the Web browser
[System requirements]
Supported OS : Windows®2000, Windows®XP
(Microsoft®.NET Framework 1.1*2 should be installed.)
CPU : Pentium II 233 MHz or higher
Memory : 128 MB or more
Free HDD space : 32 MB or more
Web browser : Internet Explorer Ver. 6.0
(Java Plug-in*3 should be installed and Javascript should be enabled.)
*2 How to install Microsoft®.NET Framework Version 1.1
(1) Download .NET Framework Version 1.1 (file named “dotnetfx.exe”) from the download center on the
Microsoft®Web site (http://www.microsoft.com/downloads/).
(When the file is unavailable from the above-mentioned URL, search for .NET Framework using Windows
Update and access the download site found.)
(2) Execute the downloaded file named dotnetfx.exe.
*3 How to install Java Plug-in
(1) Download J2SE v1.4.2 JRE from the JAVA download center on the Sun Microsystems Web site (http://java.
sun.com/j2se/1.4.2/ja/download.html).
(When the file is unavailable from the above-mentioned URL, search for “J2SE download” using a search
engine and access the download site found.)
(2) Execute the downloaded file.
• Microsoft or Windows are either registered trademarks or trademarks of Microsoft Corporation in the United
States and/or other countries.
• Pentium is trademark or registered trademark of Intel Corporation or its subsidiarie in the United States and
other countries.
• PJLink is trademark applied for registration or registered trademark of Japan Business Machine and Information
System Industries Association in japan, the United States and other countries.
• Other brand or product names are trademarks or registered trademarks of their respective holders.
EN-3
1
Copy three files (Installer_Mitsubishi.msi, Setup.Exe, and Setup.Ini) contained in the Tools folder of CD-
ROM to the hard disk of your personal computer.
2
Double-click the file named Setup.Exe.
3
When the following window appears, click Next.
Installation
Before starting installation, be sure to read “ReadMe.txt” contained in the CD-ROM.
Connection
• Use a straight-through category-5 cable for LAN connection.
• Don’t touch the metal parts of the LAN connector and LAN cable because static electricity may be discharged
from your body, causing damage to the projector.
Computer
to LAN terminal
LAN cable (option)
(100BASE-TX or 10BASE-T should be supported.)
LAN cable (option)
(100BASE-TX or 10BASE-T should be
supported.)
External HUB
to LAN terminal
Preparation/SetUp (continued)
EN-4
Preparation/SetUp (continued)
4
Select a folder to install the program, and click Next.
5
Click Next.
6
Installation starts.
• The progress of the installation process is
displayed as shown on the right.
7
When the installation process is completed, click
Close.
How to remove Mitsubishi Projector Control Device Installer
Select [Start] - [Control Panel] - [Add or Remove Programs] - [Mitsubishi Projector - Control Device Installer] and
click [Remove] (in the case of Windows®XP).
EN-5
1
Start the Projector-Control Device Installer.
・ Select [Start] - [All Programs] - [Mitsubishi] -
[Mitsubishi Projector - Control Device Installer] (in
the case of Windows®XP).
2
Click the Search button.
• Mitsubishi projector is recognized.
(Note 1)
When Mitsubishi projector isn’t recognized, check
the following.
• The firewall function has been disabled. (When it
has been enabled, search may not be conducted.)
• The personal computer and the projector are on
the same network. (For preventing unauthorized
access.)
• More than one Projector-Control Device Installer
isn’t running.
3
Select a projector and click the Assign IP button.
4
The Assign IP Address screen appears.
Setting the IP address of the projector
Before setting the IP address, check that the projector has been LAN-networked and turn on the main power of the
projector.
• For automatic IP address setting by the DHCP server, go to page 6. For IP address setting without using the
DHCP server, go to page 7.
Preparation/SetUp (continued)
EN-6
5
Select [Obtain an IP address automatically] and click
Next.
6
Click Next.
• Check that the options are marked with check-
marks as shown on the right. Keep them un-
changed for normal use.
7
Click Assign.
8
Click Finish.
9
Click the Search button.
• Check the IP address.
When using a DHCP server
Preparation/SetUp (continued)
EN-7
5
Select [Assign a specific IP address] and click Next.
6
Enter a fixed IP address (for example, 192.168.0.1)
and click Next.
7
Click Assign.
8
Click Finish.
9
Click the Search button.
• Check the IP address you set.
(Note 2)
When using the error/alert e-mail notification function
described later, click the Assign IP button and set the
subnet mask and default gateway correctly.
• For the values of the subnet mask and default
gateway, contact your network administrator.
When not using a DHCP server
Preparation/SetUp (continued)
EN-8
1
Start the Projector-Control Device Installer.
• Select [Start] - [All Programs] - [Mitsubishi] -
[Mitsubishi Projector - Control Device Installer] (in
the case of Windows®XP).
2
Press the + buttons on the left pane to expand the
tree structure until the IP address you set appears.
3
Click the Telnet Configuration tab.
4
Select the Connect tab. Press the Enter key within
5 seconds after the message shown on the right
appears.
• When it passes 5 seconds without any operation
on this screen, the screen is shaded and no key
operation is accepted. In this case, click the
Connect button again to continue setting.
5
The setting menu appears.
Telnet setting
Setting of password, display language, LAN control, and PJLink™ certification using telnet.
This section describes how to set the password, display language on the ProjectorView screen, LAN control, and
PJLink™ certification that are necessary for the operation state control tool (commercially available) that uses the
projector operation control/monitor tool ProjectorView and the industry standard PJLink™ protocol.
Preparation/SetUp (continued)
EN-9
1
Enter “0” and press the Enter key.
2
Enter a new password (example: “proj2000“) and press
the Enter key. (Default password is MITSUBISHI.)
Setting the password (Password Setup)
1
Enter “1” and press the Enter key.
2
Enter “0” for English or “1” for Japanese.
Setting the display language of ProjectorView (language)
Preparation/SetUp (continued)
EN-10
1
Enter “3” and press the Enter key.
2
To enable the e-mail notification function of Projector-
View, enter 1 and press the Enter key. (Default is OFF (0).)
(See pages 12 - 15 for ProjectorView function.)
Setting the LAN control (LAN-Controlled Mode)
1
Enter “5” and press the Enter key.
• When you don’t use PJLink™ protocol
communication, skip this item. (See page 16 for
PJLink™.)
2
To enable the PJLink™ certification:
Enter “1” and press the Enter key. (Default is ON (1).)
Setting the PJLink™ certification (PJLink certification Mode)
Preparation/SetUp (continued)
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Mitsubishi Projecteur
Mitsubishi
Mitsubishi WD3300U Manuel utilisateur
Mitsubishi
Mitsubishi VS-50PH50U Manuel utilisateur
Mitsubishi
Mitsubishi SD10U Manuel utilisateur
Mitsubishi
Mitsubishi HC7000 Manuel utilisateur
Mitsubishi
Mitsubishi HD4000U Manuel utilisateur
Mitsubishi
Mitsubishi LVP-X300U Manuel utilisateur
Mitsubishi
Mitsubishi X400 Manuel utilisateur
Mitsubishi
Mitsubishi SD105U Manuel utilisateur
Mitsubishi
Mitsubishi FD630U Manuel utilisateur
Mitsubishi
Mitsubishi HD8000 Manuel utilisateur
Mitsubishi
Mitsubishi X250 Manuel utilisateur
Mitsubishi
Mitsubishi XD80U Manuel utilisateur
Mitsubishi
Mitsubishi UL7400U Manuel utilisateur
Mitsubishi
Mitsubishi X80 Manuel utilisateur
Mitsubishi
Mitsubishi XL5U Manuel d'utilisation et d'entretien
Mitsubishi
Mitsubishi LVP-X120A Manuel utilisateur
Mitsubishi
Mitsubishi ColorView SL1U Manuel utilisateur
Mitsubishi
Mitsubishi ColorView S490U Manuel utilisateur
Mitsubishi
Mitsubishi ColorView XL1U Manuel utilisateur
Mitsubishi
Mitsubishi LVP-X120A Manuel utilisateur
Manuels Projecteur populaires d'autres marques
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur
NEC
NEC NP600S EDU Manuel utilisateur
BenQ
BenQ SH753P Manuel utilisateur
Eiki
Eiki EK-623U series Manuel utilisateur
Epson
Epson PowerLite Pro Cinema 6020UB Manuel utilisateur
Epson
Epson PowerLite Home Cinema 705HD Manuel utilisateur
