Mitsubishi LVP-X120A Manuel utilisateur
APPENDIX
X120
LCD
Projector
User Manual
MODEL LVP-X120A
Control this projector by using a personal computer
This projector can be controlled by connecting a personal computer with RS-232C terminal.
Connection
Projector + IBM PC or IBM PC compatibles
RS-232C cable
to RS-232C
terminal
to Com1
Comport
D-SUB 9P Mini DIN 8P
Note: If your PC (IBM or IBM compatible) is equipped only with a 25-pin serial port connector,
a 25-pin serial port adapter is required. Contact your dealer for details.
RS-232C cable
to RS-232C
terminal
RS-232C adaptor
for Macintosh
to modem port
or printer port
D-SUB 9PD-SUB 9PMini DIN 8P Mini DIN 8P
Projector + Macintosh
APPENDIX
Functions can be controlled by a personal computer:
• Turn the ON or OFF
• Changing input signals
• Button input by remote control
• Reading warning data
• Picture adjustment
By making a programme, you can also control this projector by a personal computer automatically.
[EXAMPLE]
Time Movement Commands to be used (ASCII code)
8:40 a.m. Turn the power ON 0 0 !
Change input to RGB 0 0 _ r 1
0:20 p.m. Turn the power OFF 0 0 "
1:00 p.m. Turn the power ON 0 0 !
3:00 p.m. Change input to VIDEO 0 0 _ v 1
5:20 p.m. Turn the power OFF 0 0 "
1) Interface
Address code Function code Data code End code
HEX 30h 30h Function Data 0Dh
ASCII '0' '0' Function Data
[Address code] 30h 30h (In ASCII code, '0' '0') fixed.
[Function code] A code of each fixed control move
[Data code] A code of each fixed control data (number) and not always indicated.
[End code] 0Dh (In ASCII code, ' ') fixed.
3) Control sequence
(1) The command from a personal computer to the projector will be sent in 400ms.
(2) The projector will send a return command 400ms* after it has received an encode. if the command isn’t
received correctly, the projector will not send the retirn command.
(3) The personal computer checks the command and confirms that if the command which has been sent has
been executed or not.
(4) This projector sends various codes, other than the return code. When having a control sequence by RS-
232C, reject other codes from personal computer side.
• * : The sending time of return command may delay depending on the condition (during changing the input
signal, playing back the PC card, etc.).
PROTOCOL RS-232C
BAUD RATE 9600 [bps]
DATA LENGTH 8 [bits]
PARITY BIT NONE
STOP BIT 1 [bits]
FLOW CONTROL NONE
This projector uses RXD, TXD and GND lines for RS-232C control.
For RS-232C cable,the reverse type cable should be used.
2) Control command diagram
The command is structured by the address code, function code, data code and end code. The length of the
command is different by each function.
Control this projector by using a personal computer (Continue)
[Example] Turn the power ON (' 'is for ASCII code)
Sending commands Status code from Meaning
from the PC etc. projector
30 30 21 0D Command for POWER ON
'0' '0' '!' ' '
30 30 21 0D Command received
'0' '0' '!' ' ' (Command echo back)
4) Operation commands
The operation commands execute the basic operation setting of this projector.It may not operate when changing
the signal.
Sending commands Status code from Meaning
from the PC etc. projector
30 30 5F 72 31 OD Command for setting the input
'0' '0' '_' 'r' '1' ' ' signal to RGB
30 30 5F 72 31 OD Command received
'0' '0' '_' 'r' '1' ' ' (Command echo back)
Button's name on remote
ASCII HEX
+ VOLUME r06 72h 30h 36h
–VOLUME r07 72h 30h 37h
EXPAND r02 72h 30h 32h
{r53 72h 35h 33h
}r2b 72h 32h 62h
$r4f 72h 34h 66h
%r59 72h 35h 39h
MENU r54 72h 35h 34h
ENTER r10 72h 31h 30h
AUTO PLAY(PC CARD)
r32 72h 33h 32h
RELEASE(PC CARD)
r22 72h 32h 32h
AUTO POSITION r09 72h 30h 39h
STILL ra4 72h 61h 34h
Sending commands Status code from Meaning
from the PC etc. projector
30 30 72 35 34 OD Command as same as MENU button
'0' '0' 'r' '5' '4' ' '
30 30 72 35 34 OD Command received
'0' '0' 'r' '5' '4' ' ' (Command echo back)
ASCII HEX
POWER ON ! 21h
POWER OFF " 22h
INPUT RGB _r1 5Fh 72h 31h
INPUT VIDEO _v1 5Fh 76h 31h
INPUT CARD _c1 5Fh 63h 31h
•POWER OFF command will not work for 1 minute after the power is turned on.
•POWER ON command will not work for 1 minute after the power is turned off.
[Example] Set the input signal to RGB (' 'is for ASCII code)
[Example] Display MENU selection bar. (' 'is for ASCII code)
5) Remote commands
The some remote control operation can be done by remote command codes.
APPENDIX
6) Warning commands
Read the past warning data. The personal computer doesn’t attache the data code onto the warning commands to
send. On the other hand, the projector which has received a command, attach the warning data as the data code
to reply.
[Example 1]
The fan was down when the power was ON and the past data of the warning was confirmed.
Sending commands Status code from Meaning
from the PC etc. projector
30 30 45 70 OD Commnd for confirm past data
'0' '0' 'E' 'p' ' '
30 30 45 70 38 32 30 30 30 30 0D
Warning command (Fan is stopped when
'0' '0' 'E' 'p' '8' '2' '0' '0' '0' '0' ' ' the power is ON) carried out
The past data
Ep* (* is 6 digits, hexadecimal notation)
*=(MBS)b1,b2,b3,b4,b5,b6,b7,b8, b9, b10, b11, b12, b13, b14, b15, b16, b17, b18, b19, b20, b21, 000(LSB)
b1=Operation time (during boot up '0' / when the power is ON, '1')
b2=Standby power short
b3=Switch power short
b4=0
b5=0
b6=0
b7=The fan is stopped.
b8=The lamp cover is not closed.
b9=The filter cover is not closed.
b10=The temperature sensor is off (Exausting fan)
b11=The temperature sensor is off (The lamp)
b12=Communication error between microcomputer
b13=Communication error between microcomputer (Parallel bus)
b14=Abnormal temperature (the lamp)
b15=Abnormal temperature (outside)
b16=Abnormal temperature (LCD)
b17=The lamp is not illuminating.
b18=Confirmation mode for the operating status
b19=0
b20=0
b21= The life of a lamp
ASCII HEX
past data Ep 45h 70h
clear past data Ec 45h 63h
7) Reading command diagram
Monitor projector operation status. The power ON, OFF and input terminal settings can be monitored.
ASCII HEX
Function Data (Receive) Function Data (Receive)
POWER ON vP 1 76h 50h 31h
POWER OFF vP 0 76h 50h 30h
INPUT RGB vI r1 76h 49h 72h 31h
INPUT VIDEO vI v1 76h 49h 76h 31h
INPUT CARD vI c1 76h 49h 63h31h
* : '8' '2' '0' '0' '0' '0' mean the numbers as shown below.
Bit
b1 b2 b3 b4 b5 b6 b7 b8 b9 b10 b11 b12 b13 b14 b15 b16 b17 b18 b19 b20 b21 0 0 0
ASCII
10000010000000000000 0000
HEX
82 0000
b1=1(The power is ON), b7=1(The fan is stopped), Other=0
8) Picture adjustment commands
The picture adjustment commands execute the picture adjustment setting of this projector. If the personal computer doesn’t
send the commands without attaching the data code, the projector which has received the command replays the setting data
as data code.
How to set the grade
The data code of CONTRAST and BRIGHTNESS is structured by the difference data of R from G, the main data and the difference
data of B from G. Use ASCII letters code to set the grade for setting data. Please refer to the table below for HEX code.
ASCII HEX
CONTRAST P 50h
BRIGHTNESS Q 51h
SHARPNESS R 52h
TINT S 53h
COLOR T 54h
ASCII '+' '–' '0' '1' '2' '3' '4' '5' '6' '7' '8' '9'
HEX 2Bh 2Dh 30h 31h 32h 33h 34h 35h 36h 37h 38h 39h
[Example 2] The TINT was set to +10 when the setting status was confirmed.
[Example 1] Set the difference data of R from G to +10, the setting main data to 0 and the difference data of
B from to -5.
Sending commands Status code from Meaning
from the PC etc. projector
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D Command for setting the
'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' ' ' picture control
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D Command received
'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' ' ' (Command echo back)
Sending commands Status code from Meaning
from the PC etc. projector
30 30 53 0D Command for confirm
'0' '0' 'S' ' 'setting of TINT
30 30 53 2B 31 30 0D Command (setting of TINT
'0' '0' 'S' '+' '1' '0' ' ' is +10) carried out
Control this projector by using a personal computer (Continue)
When a personal computer sends the command, data code will not be attached. On the other hand, the projector
which has received a command will attach the recent operating status then send.
[Example ] Input was Video when the operating status of the input terminal was confirmed.
Sending commands Status code from Meaning
from the PC etc. projector
30 30 76 49 OD Commnd for confirm input
'0' '0' 'v' 'I' ' '
30 30 76 49 76 31 0D Command (Input is Video)
'0' '0' 'v' 'I' 'v' '1' ' ' carrired out
CONTRAST
BRIGHTNESS
difference data
of R from G
-10
+00
difference data
of B from G
+10
+00
CONTRAST
BRIGHTNESS
difference data
of R from G
+10
+00
difference data
of B from G
-10
+00
• When the command of CONTRAST or BRIGHTNESS is sent from the computer, the setting of the COLOR TEMP on the
menu is set to “USER”.
• For the same condition as “HIGH” or “LOW” of the COLOR TEMP, change the CONTRAST and BRIGHTNESS settings as
shown below.
COLOR TEMP “HIGH” COLOR TEMP “LOW”
Printed in Japan871D269B1
MITSUBISHI ELECTRONICS AMERICA, INC.
5665 Plaza Drive
Cypress, CA 90630
Autres manuels pour LVP-X120A
1
Table des matières
Autres manuels Mitsubishi Projecteur
Mitsubishi
Mitsubishi XD450U Manuel utilisateur
Mitsubishi
Mitsubishi Mini-mits XD20A Manuel utilisateur
Mitsubishi
Mitsubishi SD510U Manuel utilisateur
Mitsubishi
Mitsubishi HC3800U Manuel utilisateur
Mitsubishi
Mitsubishi DLP NW31U-EST Manuel utilisateur
Mitsubishi
Mitsubishi ES100U Manuel utilisateur
Mitsubishi
Mitsubishi ColorView S490U Manuel
Mitsubishi
Mitsubishi SA51 Manuel utilisateur
Mitsubishi
Mitsubishi ColorView XL1U Manuel utilisateur
Mitsubishi
Mitsubishi FD630U Manuel utilisateur
Mitsubishi
Mitsubishi SD10U Manuel utilisateur
Mitsubishi
Mitsubishi XL30 XL25 SL25 Manuel utilisateur
Mitsubishi
Mitsubishi XL2 Manuel utilisateur
Mitsubishi
Mitsubishi X70B Manuel utilisateur
Mitsubishi
Mitsubishi LVP-X80U Manuel utilisateur
Mitsubishi
Mitsubishi HC100U Manuel utilisateur
Mitsubishi
Mitsubishi VS-50PH50U Manuel utilisateur
Mitsubishi
Mitsubishi XL5950U Manuel utilisateur
Mitsubishi
Mitsubishi XL5900U Manuel utilisateur
Mitsubishi
Mitsubishi EX240U Manuel utilisateur
Manuels Projecteur populaires d'autres marques
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur
NEC
NEC NP600S EDU Manuel utilisateur
BenQ
BenQ SH753P Manuel utilisateur
Eiki
Eiki EK-623U series Manuel utilisateur
Epson
Epson PowerLite Pro Cinema 6020UB Manuel utilisateur
Epson
Epson PowerLite Home Cinema 705HD Manuel utilisateur
