Mitsubishi Electric WD2000 Manuel

PROTOCOL RS-232C

BAUD RATE 9600 [bps]

DATA LENGTH 8 [bits]

PARITY BIT NONE

STOP BIT 1 [bit]

FLOW CONTROL NONE

Address code Function code Data code End code

HEX 30h 30h Function Data 0Dh

ASCII '0' '0' Function Data

1) Interface

Controlling the projector using a personal computer

This projector can be controlled by connecting a personal computer with RS-232C terminal.

PC-controllable functions:

• Turning the power ON or OFF

• Changing input signals

• Inputting commands by pressing the buttons on the control panel and remote control

• Menu setting

Connection

SERIAL

RS-232C cable

D-SUB 9-pin D-SUB 9-pin

To RS-232C

terminal

Important:

• Make sure that your computer and projector are turned off before connection.

• Boot up the computer first, and then plug the power cord of the projector.

(If you do not follow this instruction, the Com port may not function.)

• Adapters may be necessary depending on the PC connected to this projector. Contact your dealer for details.

This projector uses RXD, TXD and GND lines for RS-232C control.

For RS-232C cable, the reverse type cable should be used.

2) Control command diagram

The command consists of the address code, function code, data code, and end code. The length of the command

varies among the functions.

[Address code] 30h 30h (In ASCII code, '0' '0') fixed.

[Function code] A code of each fixed control move.

[Data code] A code of each fixed control data (number) and not always indicated.

[End code] 0Dh (In ASCII code, ' ') fixed.

DLPTM Projector

WD2000

3) Control sequence

(1) Send the command from the personal computer to the projector.

(2) The projector will send a return command after it receives an end code. If the command is not received cor-

rectly, the projector will not send the return command.

(3) The personal computer checks the command and confirms if the sent command has been executed or not.

(4) This projector sends various codes other than the return code. When having a control sequence by RS-232C,

reject other codes from the personal computer.

• During signal switching, the command may not take effect even when the projector sends the return command.

After signal switching completes, wait for the mode indication to disappear before sending the next command.

• When sending commands successively, wait to receive the return command of the current command before

sending a next command.

• Keep intervals of at least 400 ms between receipt of a return command and sending of a next command.

• Any commands will not be executed for 10 seconds after the power is turned on.

[Example] When turning the power ON (Figures and symbols enclosed in quotation marks are ASCII codes.):

Sending commands Status code from Description

from the PC, etc. the projector

30 30 21 0D Command for POWER ON

'0' '0' '!' ' '

30 30 21 0D Command receipt confirmation

'0' '0' '!' ' ' (Command echo back)

Sending commands Status code from Description

from the PC, etc. the projector

30 30 5F 72 31 0D Command for setting the input

'0' '0' '_' 'r' '1' ' ' signal to COMPUTER 1

30 30 5F 72 31 0D Command receipt confirmation

'0' '0' '_' 'r' '1' ' ' (Command echo back)

Operation ASCII HEX Note

POWER ON ! 21h

This command is invalid for 1 minute after the power is turned off.

POWER OFF " 22h

This command is invalid for 1 minute after the power is turned on.

INPUT COMPUTER 1 _r1 5Fh 72h 31h

This command will not be executed in Stand-by mode or when the MUTE is executed.

INPUT COMPUTER 2 _r2 5Fh 72h 32h

This command will not be executed in Stand-by mode or when the MUTE is executed.

INPUT DVI _d1 5Fh 64h 31h

This command will not be executed in Stand-by mode or when the MUTE is executed.

INPUT VIDEO _v1 5Fh 76h 31h

This command will not be executed in Stand-by mode or when the MUTE is executed.

INPUT S-VIDEO _v2 5Fh 76h 32h

This command will not be executed in Stand-by mode or when the MUTE is executed.

4) Operation commands (Not executable in stand-by mode. When the commands for input select are sent while

the splash screen is being displayed, the splash screen is only canceled.)

The operation commands are used for the basic operation setting of this projector. They may not be executed

while the signals are changed. The operation commands have no data codes.

5) Volume commands (Not executable in stand-by mode. Possible only to read during muting.)

The volume commands are used for the volume setting of this projector with the value.

[Example] When setting the volume to 15 (Figures and symbols enclosed in quotation marks are ASCII codes.):

Sending commands Status code from Description

from the PC, etc. the projector

30 30 56 4C 31 35 0D Command for setting the volume

'0' '0' 'V' 'L' '1' '5' ' '

30 30 56 4C 31 35 0D Command receipt confirmation

'0' '0' 'V' 'L' '1' '5' ' ' (Command echo back)

ITEM ASCII HEX VALUE

VOLUME VL 56h 4Ch 00 - 21

How to set the grade

Use the ASCII codes to set the grade for setting data. Please refer to the table below for the HEX code.

ASCII '0' '1' '2' '3' '4' '5' '6' '7' '8' '9'

HEX 30h 31h 32h 33h 34h 35h 36h 37h 38h 39h

[Example] When setting the input signal to COMPUTER 1 (Figures and symbols enclosed in quotation marks are

ASCII codes.):

Sending commands Status code from Description

from the PC, etc. the projector

30 30 72 35 34 0D Command operating the same

'0' '0' 'r' '5' '4' ' ' as the MENU button

30 30 72 35 34 0D Command receipt confirmation

'0' '0' 'r' '5' '4' ' ' (Command echo back)

[Example] When displaying the MENU selection bar (Figures and symbols enclosed in quotation marks are ASCII

codes.):

Button's name on remote

ASCII HEX

+ VOLUME r06 72h 30h 36h

– VOLUME r07 72h 30h 37h

KEYSTONE r43 72h 34h 33h

MUTE ra6 72h 61h 36h

{r53 72h 35h 33h

}r2b 72h 32h 62h

$r4f 72h 34h 66h

%r59 72h 35h 39h

MENU r54 72h 35h 34h

ENTER r10 72h 31h 30h

ZOOM/FOCUS r0f 72h 30h 66h

LENS SHIFT r47 72h 34h 37h

AUTO POSITION r09 72h 30h 39h

STILL ra4 72h 61h 34h

ASPECT re2 72h 65h 32h

CE re7 72h 65h 37h

7) Mute commands (Not executable in stand-by mode. When the mute commands are sent while the splash

screen is being displayed, the splash screen is not muted but only canceled.)

The mute commands are used for the mute setting of this projector with the 0 (30h) and 1 (31h).

ITEM ASCII HEX VALUE

MUTE MUTE 4Dh 55h 54h 45h 0 (OFF), 1 (ON)

6) Keystone commands (Not executable in stand-by mode. Possible only to read during muting.)

The keystone commands are used for the keystone setting of this projector with the value. The value will vary

depending on the installation conditions, etc.)

ITEM ASCII HEX VALUE

KEYSTONE (vertical) KS 4Bh 53h ±35

KEYSTONE (horizontal) KSH 4Bh 53h 48h ±25

How to set the grade

Use the ASCII codes to set the grade for setting data. Please refer to the table below for the HEX code.

ASCII '+' '–' '0' '1' '2' '3' '4' '5' '6' '7' '8' '9'

HEX 2Bh 2Dh 30h 31h 32h 33h 34h 35h 36h 37h 38h 39h

8) Remote commands (Not executable in stand-by mode. When the remote commands are sent while the splash

screen is being displayed, the splash screen is only canceled.)

Some remote control operations can be achieved by the remote command codes. The remote commands have no

data codes.

9) Password lock commands

The password lock commands control the password lock. The password lock enabling or disabling command is

sent with a 4-digit figure (password) added to the end of the data code. When the password lock is enabled or

disabled successfully, the projector sends a return command comprising the data code, password, and “1” at the

end. When enabling or disabling the password lock fails, it sends a return command with “0” at the end. There is no

reconfirmation of the password. The password input command is for enabling projection of image when password

lock has been set to DISPLAY INPUT. The password input command is sent with a 4-digit figure (password) at the

end.

ITEM ASCII HEX VALUE

Password lock PSLOCK 50h 53h 4Ch 4Fh 43h 4Bh 0**** (Disabling), 1**** (DISPLAY INPUT)

enabling/disabling 2**** (MENU ACCESS)

Password input PASS 50h 41h 53h 53h ****

**** is a 4-digit figure (password).

ASCII HEX

Function

Data (Receive)

Function

Data (Receive)

POWER ON vP 1 76h 50h 31h

POWER OFF vP 0 76h 50h 30h

INPUT COMPUTER 1 vI r1 76h 49h 72h 31h

INPUT COMPUTER 2 vI r2 76h 49h 72h 32h

INPUT DVI vI d1 76h 49h 64h 31h

INPUT VIDEO vI v1 76h 49h 76h 31h

INPUT S-VIDEO vI v2 76h 49h 76h 32h

POWER ON/OFF INPOSSIBLE vPK 0 76h 50h 4Bh 30h

POWER ON/OFF POSSIBLE vPK 1 76h 50h 4Bh 31h

NO SIGNAL SUPPLIED vSM 0 76h 53h 4Dh 30h

SIGNAL SUPPLIED vSM 1 76h 53h 4Dh 31h

LAMP OPERATING TIME vLE hhhhmm 76h 4Ch 45h hhhhmm

(on a LOW mode basis)

11)

Menu setting commands (Not executable in stand-by mode. Possible only to read during muting.)

The menu setting commands are used for the menu setting of this projector. If the personal computer sends the

command without attaching the data code, the projector attaches to the received command its current setting value

as the data code and send it back to the PC.

ITEM ASCII HEX VALUE

COLOR ENHANCER CE 43h 45h 0 (AUTO), 1 (PRESENTATION), 2 (STANDARD),

3 (THEATER), 4 (sRGB), 5 (USER)

COLOR ENHANCER-USER

CEU1 43h 45h 55h 31h

+0 (DYNAMIC), +1 (NATURAL), +2 (DETAIL)

+00 - 02 (BrilliantColorTM)

CONTRAST

PP 50h 50h ±30

BRIGHTNESS QQ 51h 51h ±30

COLOR TEMP. A 41h 1 (STANDARD), 2 (HIGH), 3 (LOW), 4 (USER)

COLOR TEMP.-USER(CONTRAST)

P 50h ±30±30±30 (R,G,B)

COLOR TEMP.-USER(BRIGHTNESS)

Q 51h ±30±30±30 (R,G,B)

COLOR T 54h ±10

TINT S 53h ±10

SHARPNESS R 52h ±05

LAMP MODE LM 4Ch 4Dh 0 (STANDARD), 1 (LOW)

AUTO POWER ON APON 41h 50h 4Fh 4Eh 0 (OFF), 1 (ON)

AUTO POWER OFF APOF 41h 50h 4Fh 46h 00 (OFF), 05, 10, 15, 30, 60

SPLASH SCREEN SS 53h 53h 0 (OFF), 1 (ON)

BACK COLOR BB 42h 42h 0 (BLACK), 1 (BLUE)

IMAGE REVERSE IR 49h 52h

0 (OFF), 1 (MIRROR), 2 (INVERT), 3 (MIRROR INVERT)

TEST PATTERN TP 54h 50h 0 (OFF), 1 (CROSS HATCH)

ZOOM/FOCUS LOCK FZL 46h 5Ah 4Ch 0 (OFF), 1 (ON)

LENS SHIFT LOCK LSL 4Ch 53h 4Ch 0 (OFF), 1 (ON)

LENS SHIFT RESET LSRST 4Ch 53h 52h 53h 54h

ASPECT SC 53h 43h 0 (AUTO), 1 (16:9), 2 (REAL), 3 (FULL)

ASPECT(Position of 16:9 image)

SCP 53h 43h 50h 0 (CENTER), 1 (UPPER), 2 (LOWER)

PASSWORD FUNCTION

PSLOCK

50h 53h 4Ch 4Fh 0**** (UNLOCK), 1**** (DISPLAY INPUT),

43h 4Bh 2**** (MENU ACCESS)

**** is a 4-digit figure (password)

MENU POSITION MP 4Dh 50h 0 (Upper left), 1 (Lower right)

CINEMA MODE CINE 43h 49h 4Eh 45h 0 (OFF), 1 (AUTO)

VIDEO SIGNAL VS 56h 53h 0 (AUTO), 1 (NTSC), 2 (PAL), 3 (SECAM) ,

4 (4.43NTSC), 5 (PAL-M), 6 (PAL-N), 7 (PAL-60)

WXGA WXGA 57h 58h 47h 41h

0 (OFF), 1 (AUTO), 2 (1280x768), 3 (1360x768), 4 (1366x768)

SETUP STU 53h 54h 55h 0 (AUTO), 1 (OFF), 2 (3.75%), 3 (7.5%)

SCART INPUT SRT 53h 52h 54h 0 (OFF), 1 (ON)

Sending commands Status code from Description

from the PC, etc. the projector

30 30 76 49 0D Command for checking the input terminal

'0' '0' 'v' 'I' ' '

30 30 76 49 76 31 0D Check result (VIDEO)

'0' '0' 'v' 'I' 'v' '1' ' '

The PC sends the command without attaching the data code to it. On the other hand, the projector attaches to the

received command its current operating status as the data code and send it back to the PC. (LAMP OPERATING

TIME: “h” and “m” represent hour and minute respectively. )

[Example] When checking the currently selected input terminal (when the INPUT VIDEO is being selected):

) Reading command diagram

The projectors operating status, such as POWER-ON/OFF, the currently selected input terminal and lamp operating

time, etc. can be monitored.

ASCII '+' '–' '0' '1' '2' '3' '4' '5' '6' '7' '8' '9'

HEX 2Bh 2Dh 30h 31h 32h 33h 34h 35h 36h 37h 38h 39h

How to set the grade

Use the ASCII codes to set the grade for setting data. Please refer to the table below for the HEX code.

[Example 1] When setting the AUTO POWER ON to ON. (Figures and symbols enclosed in quotation marks are

ASCII codes.):

[Example 2] When setting the CONTRAST R of the COLOR TEMP.-USER to +10, the CONTRAST G to 0, and

the CONTRAST B to -5. (Figures and symbols enclosed in quotation marks are ASCII codes.):

Sending commands Status code from Description

from the PC, etc. the projector

30 30 50 2B 31 30 2B 30 30 2D 30 35 0D Command for setting the

'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' ' ' picture control

30 30 50 2B 31 30 2B 30 30 2D 30 35 0D Command receipt confirmation

'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' ' ' (Command echo back)

Sending commands Status code from Description

from the PC, etc. the projector

30 30 41 50 4F 4E 31 0D Command for setting the

'0' '0' 'A' 'P' 'O' 'N' '1' ' ' AUTO POWER ON to ON

30 30 41 50 4F 4E 31 0D Command receipt confirmation

'0' '0' 'A' 'P' 'O' 'N' '1' ' ' (Command echo back)

[Example 3] When checking the TINT setting (when the TINT is set to +10). (Figures and symbols enclosed in

quotation marks are ASCII codes.):

Sending commands Status code from Description

from the PC, etc. the projector

30 30 53 0D Command for checking

'0' '0' 'S' ' 'the TINT setting

30 30 53 2B 31 30 0D Check result (+10)

'0' '0' 'S' '+' '1' '0' ' '

ITEM ASCII HEX VALUE

LANGUAGE LG 4Ch 47h 0 ( ), 1 (English), 2 (Español), 3 (Deutsch),

4 (Français), 5 (Italiano), 6 ( ), 7 ( ),

8 ( ), 9 ( )

RESET ALL

RSTALL

52h 53h 54h 41h 4Ch 4Ch

HORIZ.POSITION HP 48h 50h + (increment), - (decrement)*1

VERT. POSITION VP 56h 50h + (increment), - (decrement)*1

FINE SYNC. FN 46h 4Eh 00 - 31

TRACKING TRK 54h 52h 4Bh + (increment), - (decrement)*1

COMPUTER INPUT CIN 43h 49h 4Eh 0 (RGB), 1 (YCBCR/YPBPR), 2 (AUTO)

HOLD HLD 48h 4Ch 44h 0 (OFF), 1 (ON)

HOLD BEGIN HLB 48h 4Ch 42h 00 - 99

HOLD END HLE 48h 4Ch 45h 00 - 99

CLAMP POSITION CLP 43h 4Ch 50h 001 - 255

CLAMP WIDTH CLW 43h 4Ch 57h 01 - 63

VERT. SYNC VSC 56h 53h 43h 0 (AUTO), 1 (OFF)

OVER SCAN VOS 56h 4Fh 53h 00 (90%) - 10 (100%)

LPF LPF 4Ch 50h 46h 0 (OFF), 1 (ON)

SHUTTER(U) SHU 53h 48h 55h 00 - 38

SHUTTER(L) SHL 53h 48h 4Ch 00 - 38

SHUTTER(LS) SHLS 53h 48h 4Ch 53h 00 - 63

SHUTTER(RS) SHRS 53h 48h 52h 53h 00 - 63

*1) Setting range differs depending on the input signals.

• Some commands are not executed depending on the input signal. The operational restrictions same as those

on the menu setting are applied. Refer to “Menu operation” in the User Manual for more details.

[Example 4] When setting the GAMMA MODE of the COLOR ENHANCER-USER to DETAIL, the BrilliantColorTM

to 2. (Figures and symbols enclosed in quotation marks are ASCII codes.):

Sending commands Status code from Description

from the PC, etc. the projector

30 30 43 45 55 31 2B 32 2B 30 32 0D Command for setting the

'0' '0' 'C' 'E' 'U' '1' '+' '2' '+'0' '2' ' ' picture control

30 30 43 45 55 31 2B 32 2B 30 32 0D Command receipt confirmation

'0' '0' 'C' 'E' 'U' '1' '+' '2' '+'0' '2' ' ' (Command echo back)

Autres manuels pour WD2000

Autres manuels Mitsubishi Electric Projecteur

Mitsubishi Electric

Mitsubishi Electric WD390U-EST Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric XD206U Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric PocketProjector PK10 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric WL6700LU Manuel

Mitsubishi Electric

Mitsubishi Electric DLP HC3900 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric UD8400U Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric HD4000 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric EX53U Manuel d'utilisation et d'entretien

Mitsubishi Electric

Mitsubishi Electric WD385U-EST Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric XD206U-G Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MH2850U Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric ColorView XD300U Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric WL6700LU Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric XD500U-ST Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric DLP UD740U Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric XL7100U Manuel

Mitsubishi Electric

Mitsubishi Electric DLP HC3200 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric HC5000 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric HC7800D Guide d'installation

Mitsubishi Electric

Mitsubishi Electric DLP XD8100U Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric XD221U Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric HC3900 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric XD360U-EST Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric XD80U Manuel utilisateur

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur

NEC

NEC NP600S EDU Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Christie

Christie LHD700 Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

InFocus

InFocus LitePro 560 Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur