Mitchell Ram ProMaster 2016 Guide de configuration
Back To Article
2016 GENERAL INFORMATION
Vehicle Quick Reference - Ram ProMaster
CAPACITIES AND RECOMMENDED FLUIDS
SPECIFICATIONS
SPECIFICATIONS
ENGINE
Description Type Capacities
U.S. Metric
Cooling System
(1) Engine Coolant (3.6L
Engine)
MOPAR® Antifreeze/Coolant
10 Year/150, 000 Mile Formula
OAT (Organic Additive
Technology) meeting the
requirements of Material
Standard MS-90032.
10.5 Quarts 10 Liters
(2) Engine Coolant (3.0L
Diesel Engine)
MOPAR® Antifreeze/Coolant
10 Year/150, 000 Mile Formula
OAT (Organic Additive
Technology)
12.7 Quarts 12 Liters
Engine Oil with Filter
Engine Oil (3.6L Engine)
We recommend you use API
Certified SAE 5W-20 Engine
Oil, meeting the requirements
of Material Standard MS-6395
such as MOPAR, Pennzoil, and
Shell Helix. Refer to your
engine oil filler cap for correct
SAE grade.
6 Quarts 5.6 Liters
Engine Oil Filter (3.6L
Engine)
MOPAR® Engine Oil Filter
Kit N/A N/A
Engine Oil (3.0L Diesel
Engine)
Only use ACEA C3 5W-30
Synthetic Low Ash engine oil
meeting Material Standard MS-
11106 or Pennzoil Ultra Euro L
full synthetic 5W-30 motor oil.
9.5 Quarts 9.0 Liters
Engine Oil Filter (3.0L
Diesel Engine)
MOPAR® Engine Oil Filter
Kit N/A N/A
Fuel (approximate)
Fuel Selection (3.6L
Engine) 87 Octane, 0-15% Ethanol. 24 Gallons 90 Liters
Description Type Capacities
U.S. Metric
Fuel Selection (3.0L
Diesel Engine)
Use good quality diesel fuel
from a reputable supplier in
your vehicle. Federal law
requires that you must fuel this
vehicle with Ultra Low Sulfur
Highway Diesel fuel (15 ppm
Sulfur maximum) and prohibits
the use of Low Sulfur Highway
Diesel fuel (500 ppm Sulfur
maximum) to avoid damage to
the emissions control system.
For most year-round service,
No. 2 diesel fuel meeting
ASTM specification D-975
Grade S15 will provide good
performance. We recommend
you use a blend of up to 5%
biodiesel, meeting ASTM
specification D-975 with your
diesel engine. This vehicle is
compatible with biodiesel
blends greater than 5% but no
greater than 20% biodiesel
meeting ASTM specification D-
7467 provided the shortened
maintenance intervals are
followed as directed.
NOTE:
If climatize or diesel
Number 1 ULSD fuel is
not available, and you are
operating below
(20°F/-6°C), in
sustained arctic
conditions, Mopar
Premium Diesel Fuel
Treatment (or equivalent)
is recommended to avoid
gelling.
24 Gallons 90 Liters
Fuel Filter (3.0L Diesel
Engine)
We recommend you use
MOPAR Fuel Filter. Must meet
3 micron rating. Using a fuel
filter that does not meet the
manufacturers filtration and
water separating requirements
can severely impact fuel system
life and reliability.
N/A N/A
Diesel Exhaust Fluid (DEF)
Description Type Capacities
U.S. Metric
3.0L Diesel Engine
MOPAR Diesel Exhaust Fluid
(API Certified) (DEF) or
equivalent that has been API
Certified to the ISO 22241
standard. Use of fluids not API
Certified to ISO 22241 may
result in system damage.
5 Gallons 18.9 Liters
A/C Refrigerant System
A/C R-134a Pounds Kilograms
(1) System fill capacity includes heater and coolant recovery bottle filled to MAX level.
(2) Includes heater and coolant recovery bottle filled to MAX level. Add 2.9 Qts (2.8 L) if equipped with a
rear heater.
CAUTION:
Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle
due to manufacturing tolerance and refill procedure.
SPARK PLUGS
Description Type Gap
U.S. Metric
Spark Plugs (3.6L Engine) Champion® 0.043 in 01.1 mm
TRANSMISSION
Description Type Capacities
U.S. Metric
Automatic
62TE Service Fill
MOPAR® ATF+4
Automatic Transmission
Fluid
5.5 Quarts 5.2 Liters
(1) 62TE Overhaul Fill
MOPAR® ATF+4
Automatic Transmission
Fluid
9.0 Quarts 8.5 Liters
(2) M40MTA Transmission
Full synthetic 75W-85
manual transmission fluid
meeting the API GL4
specification.
N/A N/A
(2) M40MTA Control Unit
MOPAR® C Series DDCT
SAE 75W Hydraulic Fluid
or equivalent.
N/A N/A
(2) M40MTA Hydraulic
Clutch Operating System
MOPAR® Brake and
Clutch Fluid DOT 4 Motor
Vehicle or equivalent.
N/A N/A
(1) Dry fill capacity. Depending on type and size of internal cooler, length and inside diameter of cooler
lines, or use of an auxiliary cooler, these figures may vary. Refer to the appropriate service information
for the correct procedures.
(2) Failure to use the correct fluid may affect the function or performance of your transmission.
Description Type Capacities
U.S. Metric
CAUTION:
Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle
due to manufacturing tolerance and refill procedure.
CHASSIS
Description Type Capacities
U.S. Metric
Chassis Systems
Brake Master Cylinder We recommend you use
MOPAR DOT 4. N/A N/A
Power Steering Reservoir
Use Pentosin CHF 11S
power steering fluid meeting
Material Standard MS-
11655.
N/A N/A
Â
CAUTION:
Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle
due to manufacturing tolerance and refill procedure.
FUSE - RELAY LOCATIONS AND TYPES
SPECIFICATIONS
SPECIFICATIONS
NOTE: Refer to the appropriate SYSTEM WIRING DIAGRAMS article for Relay description
and location information.
The Front Power Distribution Center is located on the driver's side of the engine
compartment. To access the fuses, remove the cover.
The ID number of the electrical component corresponding to each fuse can be
found on the back of the cover.
Fig. 1: Power Distribution Center
Courtesy of CHRYSLER GROUP, LLC
POWER DISTRIBUTION CENTER
Cavity Maxi Fuse Mini Fuse Description
F01 40 Amp Orange - Electronic Stability Control (ESC)
Pump
F02 20 Amp Yellow (3.6
Gasoline Engine) -Starter Relay 3.6L (3.6 Gasoline
Engine)
F02 50 Amp Red (3.0
Diesel Engine) - Glow Plug Unit (3.0 Diesel Engine)
F04 50 Amp Red (3.6
Gasoline Engine) -
Secondary Power Distribution Center
(PDC) (Trans Power Relay, Vacuum
Pump, KL30 for the Shifter
Transmission Module [STM]) (3.6
Gasoline Engine)
F04 40 Amp Orange (3.0
Diesel Engine) - Fuel Filter Heater (3.0 Diesel Engine)
F05 30 Amp Green - SELESPEED Pump RELE (3.0 Diesel
Engine) - If Equipped
F06
40 Amp Orange (non
A/C)
60 Amp Blue (A/C)
- Engine Cooling Fan - 2nd Speed
F07 50 Amp Red (non A/C)
60 Amp Blue (A/C) - Engine Cooling Fan - 1st Speed
F08 40 Amp Orange - Passenger Compartment Blower
F09 - 15 Amp Blue Rear Power Outlet
Cavity Maxi Fuse Mini Fuse Description
F10 - 15 Amp Blue Horn
F11 - 15 Amp Blue Fuel Pressure Regulator (MPROP)-DRV
(3.0 Diesel Engine) - If Equipped
F14 - 20 Amp Yellow Power Outlet
F15 - 7.5 Amp Brown USB Charger
F16 - 7.5 Amp Brown
KL15 Shifter Transmission Module
(STM) (3.6), KL15 Starter Relay Coil
(3.6 Gasoline Engine)
F16 - 7.5 Amp Brown
KL15 Manual Transmission Automated
(MTA), KL15 Gear Selector Unit, KL15
Engine Control Module (ECM), KL15
Starter Relay Coil (3.0 Diesel Engine)
F17 - 20 Amp Yellow Engine Control Module (ECM),
Injectors (3.6 Gasoline Engine)
F17 - 20 Amp Yellow Secondary Loads, Engine Control
Module (ECM) (3.0 Diesel Engine)
F18 - 7.5 Amp Brown
KL30 Engine Control Module (ECM),
KL30 Main Relay Coil (3.6 Gasoline
Engine)
F18 - 7.5 Amp Brown
KL30 Manual Transmission Automated
(MTA), KL30 Engine Control Module
(ECM), KL30 Main Relay Coil (3.0
Diesel Engine)
F19 - 7.5 Amp Brown A/C Compressor (If Equipped)
F20 - 30 Amp Green Windshield Wiper
F21 - 15 Amp Blue Fuel Pump
F22 - 20 Amp Yellow Engine Control Module (ECM), Ignition
Coils (3.6 Gasoline Engine)
F22 - 20 Amp Yellow Engine Control Module (ECM), Primary
Loads (3.0 Diesel Engine)
F23 - 20 Amp Yellow Electronic Stability Control (ESC)
Valves
F24 - 7.5 Amp Brown KL15 Vacuum pump relay coil (3.6
Gasoline Engine) - If Equipped
F30 - 15 Amp Blue Heated Mirrors
Fig. 2: Additional Fuse Box
Courtesy of CHRYSLER GROUP, LLC
The additional fuse box is located inside the front PDC Box.
POWER DISTRIBUTION CENTER ADDITIONAL FUSES
Cavity Mini Fuse Description
F61 20 Amp Yellow Vacuum Pump (3.6 Gasoline Engine) - If Equipped
F62 30 Amp Green Transmission Power RELE (3.6 Gasoline Engine) -
If Equipped
F64 7.5 Amp Brown Urea Pump (3.0 Diesel Engine) - If Equipped
F65 25 Amp White Urea NOX Sensor 1-2 - PM Sensor (3.0 Diesel
Engine) - If Equipped
F66 5 Amp Beige Shifter Transmission Module (STM) (3.6 Gasoline
Engine) - If Equipped
Fig. 3: Interior Fuse Panel
Courtesy of CHRYSLER GROUP, LLC
The interior fuse panel is part of the Body Control Module (BCM) and is located on the driver's side under the
instrument panel.
INTERIOR FUSES
Cavity Mini Fuse Description
F12 10 Amp Red Right Low Beam
F13 10 Amp Red Left Low Beam
F31 5 Amp Beige INT/A
F32 10 Amp Red SBMT
F34 7.5 Amp Brown Clearance Lights
F36 15 Amp Blue +30 (ACM - TPCU - RRM - DLC)
F37 5 Amp Beige INT (BRAKE NO - IPC)
F38 15 Amp Blue Central Locking
F42 5 Amp Beige INT (BSM - SAS - BRAKE NC)
F43 20 Amp Yellow Bi-Directional Washer Pump
F47 20 Amp Yellow Driver Power Window
F48 20 Amp Yellow Passenger Power Window
F49 5 Amp Beige INT (PAM - CCS - RRM - ECM)
F50 7.5 Amp Brown INT (ORC)
F51 5 Amp Beige INT (REAR CAMERA-AUX)
F53 5 Amp Beige +30 (IPC)
F90 7.5 Amp Brown Left High Beam
F91 7.5 Amp Brown Right High Beam
F92 7.5 Amp Brown Left Fog Lamp
F93 7.5 Amp Brown Right Fog Lamp
Fig. 4: Right Central Pillar Fuse Panel
Courtesy of CHRYSLER GROUP, LLC
The right central pillar fuse panel is located on the interior side at the base of the passenger side B pillar.
RIGHT CENTRAL PILLAR FUSES
Cavity Mini Fuse Description
F81 7.5 Amp Brown Seat Heater
F83 20 Amp Yellow Rear Left Windows Heater
F84 20 Amp Yellow Rear Right Windows Heater
F86 20 Amp Yellow Auxiliary Switch (From Battery) - If Equipped
F87 20 Amp Yellow Auxiliary Switch (From Ignition) - If Equipped
HOISTING
STANDARD PROCEDURE
STANDARD PROCEDURE - HOISTING
Fig. 5: Hoisting And Jacking Points
Courtesy of CHRYSLER GROUP, LLC
1 - FRAME CONTACT LIFT (SINGLE POST)
1 - CHASSIS LIFT (NON-AXLE DUAL POST)
1 - OUTBOARD LIFT (DUAL POST)
1 - FLOOR JACK
Refer to Owner's Manual provided with vehicle for proper emergency jacking procedures.
WARNING: The hoisting and jack lifting points provided are for a complete vehicle. When the
engine or rear suspension is removed from a vehicle, the center of gravity is
altered making some hoisting conditions unstable. Properly support or secure
vehicle to hoisting device when these conditions exist. Failure to follow these
instructions may result in serious or fatal injury.
WARNING: Support the vehicle by supplemental means before performing any work on the air
suspension system to prevent the vehicle from changing height. Before any given
component is to be serviced it must be deflated. Servicing the air suspension
system without supplemental support, or with pressure in the specific component,
can cause possible serious or fatal injury.
Table des matières
