MINN KOTA ULTERRA Manuel utilisateur

ULTERRA™

BOW-MOUNT TROLLING MOTOR

INSTALLATION INSTRUCTIONS

INTRODUCTION

Made by Minn Kota

Johnson Outdoors

Marine Electronics, Inc.

121 Power Drive

Mankato, MN 56001 USA

Trolling Motors

Produced in 2015

SER NO R365 MK12345

ULTERRA 80/US2/IPLINK-45"_BT

MODEL 1358923

NOTE: The serial number on your Ulterra is located

inside the mount near the motor rests. EXAMPLE

THANK YOU

Thank you for choosing Minn Kota. We believe that you should spend more time ﬁshing and less time positioning your boat.

That’s why we build the smartest, toughest, most intuitive trolling motors on the water. Every aspect of a Minn Kota trolling

motor is thought out and rethought until it’s good enough to bear our name. Countless hours of research and testing provide you

the Minn Kota advantage that can truly take you “Anywhere. Anytime.” We don’t believe in shortcuts. We are Minn Kota. And we

are never done helping you catch more ﬁsh.

MOTOR INFORMATION (FOR CUSTOMER REFERENCE ONLY)

Model:__________________________________________________________________________________________________________________________

Serial Number: ________________________________________________________________________________________________________________

Purchase Date: ________________________________________________________________________________________________________________

Store Where Purchased: _____________________________________________________________________________________________________

REGISTRATION

Remember to keep your receipt and immediately register

your trolling motor. A registration card is included with your

motor or you can complete registration on our website at

minnkotamotors.com.

SERIAL NUMBER

Your Minn Kota 11-character serial number is very important.

It helps to determine the speciﬁc model and year of

manufacture. When contacting Consumer Service or registering

your product, you will need to know your product’s serial

number. We recommend that you write the serial number

down so that you have it available for future reference.

NOTE: Do not return your Minn Kota motor to your retailer. Your retailer is not authorized to repair or replace this unit.

You may obtain service by: calling Minn Kota at (800) 227-6433; returning your motor to the Minn Kota Factory Service

Center; sending or taking your motor to any Minn Kota authorized service center. A list of authorized service centers is

available on our website, at minnkotamotors.com. Please include proof of purchase, serial number and purchase date for

warranty service with any of the above options.

minnkotamotors.com | 3

SAFETY CONSIDERATIONS

WARNING

You are responsible for the safe and prudent operation of your vessel. We have designed your Minn Kota product to be an

accurate and reliable tool that will enhance boat operation and improve your ability to catch ﬁsh. This product does not relieve

you from the responsibility for safe operation of your boat. You must avoid hazards to navigation and always maintain a

permanent watch so you can respond to situations as they develop. You must always be prepared to regain manual control of

your boat. Learn to operate your Minn Kota product in an area free from hazards and obstacles.

WARNING

Never run the motor out of the water, as this may result in injuries from the rotating propeller. The motor should be disconnected

from the power source when it is not in use or is oﬀ the water. When connecting the power-supply cables of the motor to the

battery, ensure that they are not kinked or subject to chafe and route them in such a way that persons cannot trip over them.

Before using the motor make sure that the insulation of the power cables is not damaged. Disregarding these safety precautions

may result in electric shorts of battery(s) and/or motor. Always disconnect motor from battery(s) before cleaning or checking

the propeller. Avoid submerging the complete motor as water may enter the lower unit through control head and shaft. If the

motor is used while water is present in the lower unit considerable damage to the motor can occur. This damage will not be

covered by warranty.

WARNING

Take care that neither you nor other persons approach the turning propeller too closely, neither with body parts nor with objects.

The motor is powerful and may endanger or injure you or others. While the motor is running watch out for persons swimming

and for ﬂoating objects. Persons whose ability to run the motor or whose reactions are impaired by alcohol, drugs, medication,

or other substances are not permitted to use this motor. This motor is not suitable for use in strong currents. The constant noise

pressure level of the motor during use is less than 70dB(A). The overall vibration level does not exceed 2,5 m/sec2.

Please thoroughly read the user manual. Follow all instructions and heed all safety and cautionary notices. Use of this motor

is only permitted for persons that have read and understood these user instructions. Minors may use this motor only under

adult supervision.

WARNING

When stowing or deploying the motor, keep ﬁngers clear of all hinge and pivot points and all moving parts. In the event of

unexpected operation, remove power leads from the battery.

WARNING

It is recommended to only use Johnson Outdoors approved accessories with your Minn Kota motor. Using non-approved

accessories including to mount or control your motor may cause damage, unexpected motor operation and injury. Be sure to use

the product and approved accessories, including remotes, safely and in the manner directed to avoid accidental or unexpected

motor operation. Keep all factory installed parts in place including motor and accessory covers, enclosures and guards.

KNOW YOUR BOAT

Keel

Bow

Hull

Bow

Stern

Port

Port Starboard

Starboard

Gunwale

Transom

Inboard

Outboard

minnkotamotors.com | 5

INSTALLATION

INSTALLING THE ULTERRA

Your new Ulterra comes with everything you’ll need to directly install it to the boat. This motor can be directly mounted to the

boat or it may be coupled with a Minn Kota quick release bracket for ease of mounting and removal. For installation with a quick

release bracket, refer to the installation instructions provided with the bracket. For compatible quick release mounting bracket,

please visit minnkotamotors.com. To install the motor directly to the boat, please follow the instructions provided in this manual.

Please review the parts list, mounting considerations and tools needed for installation prior to getting started. For additional

product support and to locate your nearest dealer, please visit minnkotamotors.com.

INSTALLATION PARTS LIST

19 20 18

312

Item /

Assembly Part # Description Qty.

1✖MOTOR ASSEMBLY 1

AA 2994859 BAG ASY-TERROVA/V2,RUB.BUMPERS 1

22325110 PAD, FOOTPEDAL 5

BB 2994917 BAG ASSY, ULTERRA MTG HARDWARE 1

32203430 SCREW-1/4-20 X 2.0 HHCS SS 6

42203431 SCREW-1/4-20 X 0.5 HHCS SS 6

52201725 WASHER-CLIPPED, 1/4", 1.00" OD 6

62261713 WASHER-1/4 FLAT 18-8 SS 6

72263103 NUT-1/4-20 NYLOCK SS 6

82301720 WASHER-MOUNTING - RUBBER 6

92203800 STRAP, HOLD DOWN 1

10 2994075 tREMOTE ASSEMBLY, IPILOT 1

11 2994076 tREMOTE ASSEMBLY LINK

TOUCHSCREEN 1

p2397101 tMANUAL, QUICK REF., iPILOT 1.6 1

p2397103 tMANUAL-QUICK REF., iPILOT 3.0 1

12 2390800 tLANYARD, REMOTE W/ CARABINER 1

13 2373241 tCABLE, USB REMOTE CHARGER LINK 1

14 2375901 tADAPTER, USB DC POWER LINK 1

15 2996400 tHEADING SENSOR SEMBLY 1

16 490389-1 tCABLE, ETH (M12-M-M12-F, 30' 1

17 2211415 CABLE-EXTENSION, PD/AP 110" 1

CC 1378132 80# THRUST PROP KIT 1

DD 1378160 112# THRUST PROP KIT 1

18 2262658 PIN-DRIVE 1" X 3/16" S/S 1

19 2091701 WASHER-PROP (LARGE) MAX101 1

20 2093101 NUT-PROP,NYLOC,LG,MX101 3/8 SS 1

21 2331160 PROP-WW2 (4") w/ADP.RING 1

2341160 PROP-WW2 (4.5) w/ADP.RING 1

p2207113 MANUAL, INSTALL GUIDE, ULTERRA 1

22 2994740 FOOT PEDAL ASSY, ULTERRA 1

pNot shown on Parts Diagram.

✖This part is included in an assembly and cannot be ordered individually.

tOnly available with models factory installed with i-Pilot or i-Pilot Link.

INSTALLING THE ULTERRA

• #2 Phillips Screwdriver

• #3 Phillips Screwdriver

• Drill

• 9/32" Drill Bit

• A person to help with

installation

MOUNTING CONSIDERATIONS

TOOLS AND RESOURCES REQUIRED

INSTALLATION

a. Place the mount on an elevated, level surface

such as a workbench or the tailgate of a pickup.

The motor, as removed from the box, should be in

the stowed position.

b. Remove the four sideplate screws using a #3 or

#2 Phillips screwdriver. Two of these screws will

be located on each side of the mount.

It is recommended that the motor be mounted as close to the keel or centerline of

the boat as possible. Make sure the area under the mounting location is clear to drill

holes and install nuts and washers. Make sure the motor rest is positioned far enough

beyond the edge of the boat. The motor must not encounter any obstructions as it is

lowered into the water or raised into the boat when stowed and deployed. Consider

a quick release or adapter bracket with the installation of your motor. To view a list of

accessories, please visit minnkotamotors.com.

c. Remove the Right Sideplate to access the

Mounting Slots.

d. Remove the Left Sideplate to access the

Mounting Holes.

View accessories

available for your

trolling motor at

minnkotamotors.

com.

NOTE: This motor weighs approximately 70 lbs.

We recommend having a second person help with

the installation.

Deployed Stowed

Left Sideplate

Right

Sideplate

Right

Sideplate

Screw Screw

Left Sideplate

Screw Screw

Installing the Ulterra

minnkotamotors.com | 7

INSTALLING THE ULTERRA

e. Under the Left Sideplate, the Extension Damper

obstructs access to the left front Mounting Hole.

f. Using a small Screw Driver, remove the two

5/16" E-clips holding the Extension Damper in

place. Once the E-clips are removed, slide the

Extension Damper oﬀ the Mount to expose the

left rear Mounting Hole. Set the two E-clips and

Extension Damper in a safe place so they are not

misplaced before they are reassembled later in

the installation.

g. Make sure the Power Cables from the battery

are disconnected, or that the breaker, if equipped,

is “oﬀ”.

E-clips Extension Damper

Extension Damper

E-clip

Mounting Hole

Power Cables

Deck of Boat

Keel

Mount

h. Place the motor on the bow of the boat. Place

the motor as close to the centerline or keel of

the boat as possible. The motor can be installed

on either the Port or Starboard side of the boat

based on personal preference. Reviewing the

mounting considerations at the beginning of the

installation section.

WARNING

Make sure the motor is mounted on a level surface and is not

connected to a power source.

WARNING

Do not deploy the motor until it is fully mounted to the boat.

Illustrations are for reference only. Deploying your motor

before it is mounted to the boat may cause injury.

NOTE: The Emergency Strap (Item #9) is used

for Manually Stowing the Ulterra. The Emergency

Strap is not secured during installation. Store it

on your boat in the event that you would need

to manually stow the motor. To learn how, please

refer to the "Manually Stowing the Ulterra"

section of the Owner's Manual.

INSTALLING THE ULTERRA

i. Make sure the slot on the underside of the Base

Extrusion is aligned with the outermost part of

the gunwale of the boat. This will ensure that the

Shaft has a minimum clearance of 1-1/2" when

it is deployed. The lower unit when stowed and

deployed must not encounter any obstructions.

j. Check to be sure that the Mount is level. Use the

Rubber Washers (Item #8) provided to create a

level surface if necessary.

Gunwale

Slot

Base

Extrusion

Bow

k. It is recommended to mark at least 4 of the 6

holes in the Base Extrusion to have a minimum

of two bolts on each side that are located the

farthest apart. Ideal installation would allow for

6 bolts to be used, with a minimum of 4.

l. Make sure the area under the mounting location

is clear to drill holes and install nuts and washers.

Drill through the marked holes using a 9/32"

drill bit.

ITEM(S) NEEDED

Mounting Holes

Mounting Slots Base Extrusion

#8 x 6

Shaft

Gunwale 1-1/2"

Minimum

WARNING

Do not deploy the motor until it is fully mounted to the boat.

Illustrations are for reference only. Deploying your motor

before it is mounted to the boat may cause injury.

minnkotamotors.com | 9

INSTALLING THE ULTERRA

m. Mount the motor to the boat using the provided

hardware. Place the installation hardware for the

side of the mount where the Power Tilt is located

ﬁrst. This is the opposite side of the mount from

where the Extension Damper was removed. The

base of the Mount where the Power Tilt is located

has Mounting Slots and the side where the

Extension Damper is located has Mounting Holes.

NOTE: To prevent seizing of the stainless steel

hardware, do not use high speed installation

tools. Wetting the screws or applying an anti-

seize may help prevent seizing.

NOTE: The Long Bolts, Flat Washers and

Nylock Nut are not used when installing the

Ulterra with a Quick Release Bracket.

UTION

Use extra care to avoid pinching and damaging the sensor

wires that run along side of the Base Extrusion when installing

and tightening the motor mounting bolts.

Power Tilt Mounting Slots

Clipped

Washer Quick Release Bracket

Hex Head Bolt

#3 x 3 #6 x 3 #5 x 3 #7 x 3 #4 x 3

ITEM(S) NEEDED

n. If installing with a Quick Release Bracket,

install the motor with the Hex Head Bolts (Item

#4) and Clipped Washers (Item #5). Orientate

the Clipped Washers so that the ﬂat side of the

washer is towards the Base Extrusion. The Bolt

should pass through the Clipped Washer and

into a Quick Release Bracket. Leave at least 1/4"

space between the Hex Head Bolt and Clipped

Washer in order to slide the Base Extrusion under

the Clipped Washer and into place.

INSTALLING THE ULTERRA

o. If installing directly to the boat deck, install

the motor with the Long Bolts (Item #3), Clipped

Washer (Item #5), Flat Washer (Item #6) and

Nylock Nut (Item #7). Orientate the Clipped

Washers so that the ﬂat side of the washer is

towards the Base Extrusion. The Bolt should pass

through the Clipped Washer, the Rubber Washer

and then through the Boat Deck. The Bolt should

be secured by ﬁrst adding the Flat Washer (Item

#6) to the Bolt and securing with a Nylock Nut

(Item #7). Leave at least 1/4" space between the

Hex Head Bolt and Clipped Washer and the deck

of the boat. This will leave enough space to slide

the Base Extrusion between the Clipped Washer

and Rubber Washer and into place.

NOTE: The Short Bolts are not used when

installing the Ulterra directly to the boat.

p. Slide the Base Extrusion into place under the

Bolts that were just installed.

q. If installing with a Quick Release Bracket,

the Base Extrusion should slide between the

Quick Release Bracket and the Clipped Washers.

Hold the Clipped Washers up on the Hex Head

Bolt, so the Clipped Washer will sit on top of the

Base Extrusion.

r. If installing directly to the boat deck, the

Base Extrusion should slide between the Clipped

Washer and the Rubber Washer. Hold the Clipped

Washers up on the Long Bolt, so the Clipped

Washer will sit on top of the Base Extrusion.

11q

11r

Boat Deck

Power Tilt

Base

Extrusion

Base Extrusion

Power Tilt

Quick Release Bracket

Boat Deck

10o

Long Bolts

Clipped

Washer

Clipped

Washer

Clipped

Washer

Rubber Washer

Rubber

Washer

Flat Washer

Nylock Nut

Power

Tilt

Autres manuels pour ULTERRA

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels MINN KOTA Moteur

MINN KOTA

MINN KOTA Endura 50 Manuel utilisateur

MINN KOTA

MINN KOTA Riptide Ulterra Manuel utilisateur

MINN KOTA

MINN KOTA Riptide 80 ST Manuel utilisateur

MINN KOTA

MINN KOTA EO 1/2 HP Manuel utilisateur

MINN KOTA

MINN KOTA MAXXUM Series Manuel utilisateur

MINN KOTA

MINN KOTA ULTERRA Manuel utilisateur

MINN KOTA

MINN KOTA RIPTIDE POWERDRIVE Manuel utilisateur

MINN KOTA

MINN KOTA ULTREX Manuel utilisateur

MINN KOTA

MINN KOTA ULTERRA Guide de dépannage

MINN KOTA

MINN KOTA FORTREX Manuel utilisateur

MINN KOTA

MINN KOTA RIPTIDE POWERDRIVE Manuel utilisateur

MINN KOTA

MINN KOTA EDGE Manuel utilisateur

MINN KOTA

MINN KOTA RIPTIDE TERROVA Manuel utilisateur

MINN KOTA

MINN KOTA RIPTIDE TERROVA Manuel utilisateur

MINN KOTA

MINN KOTA 1810244 Manuel utilisateur

MINN KOTA

MINN KOTA RIPTIDE INSTINCT QUEST Manuel utilisateur

MINN KOTA

MINN KOTA RIPTIDE TERROVA Manuel utilisateur

MINN KOTA

MINN KOTA MKA 32 QRB Manuel utilisateur

MINN KOTA

MINN KOTA TERROVA Manuel utilisateur

MINN KOTA

MINN KOTA ULTERRA QUEST Manuel utilisateur

MINN KOTA

MINN KOTA RIPTIDE TERROVA 1363707 Manuel utilisateur

MINN KOTA

MINN KOTA VANTAGE Manuel utilisateur

MINN KOTA

MINN KOTA ULTERRA Manuel utilisateur

MINN KOTA

MINN KOTA TRAXXIS Manuel utilisateur

Manuels Moteur populaires d'autres marques

Rotax

Rotax 125 senior MAX evo Manuel utilisateur

Kohler

Kohler K361 Manuel utilisateur

MTD

MTD OHV Series Manuel utilisateur

Kohler

Kohler COMMAND CH18-745 Manuel utilisateur

Mercury

Mercury D4.2L D-Tronic Manuel utilisateur

Selve

Selve SE Plus-RC Series Manuel utilisateur

Perkins

Perkins 1206E-E66TA Manuel utilisateur

Skov

Skov DA 174 Manuel

Rossi

Rossi TX11 Series Manuel utilisateur

Siemens

Siemens SIMOTICS T-1FW3 Feuille d'instructions

AL-KO

AL-KO PRO 350 Manuel utilisateur

MTU

MTU 12 V 4000 Lx4 Manuel utilisateur

Nanni

Nanni N3.30 Manuel d'instructions

Nanni

Nanni N5.160 CR2 Manuel utilisateur

KSB

KSB SuPreme Series Instructions d'installation

Hiwin

Hiwin EM1 Series Manuel utilisateur

Rotax

Rotax 912 i series Mode d'emploi

Siemens

Siemens SIMOTICS XP 1MB1 Manuel utilisateur