MINN KOTA FORTREX Manuel utilisateur

FORTREX®

BOW-MOUNT TROLLING MOTOR

Installation Instructions

INTRODUCTION

Made by Minn Kota

Johnson Outdoors

Marine Electronics, Inc.

121 Power Drive

Mankato, MN 56001 USA

Trolling Motors

Produced in 2012

Fortrex 80/45

MODEL 1368660

SER NO M365 MK12345

EXAMPLE

NOTICE: The serial number on your Fortrex is located

near the Momentary Switch underneath the side of the

Foot Pedal.

THANK YOU

Thank you for choosing Minn Kota. We believe that you should spend more time ﬁshing and less time positioning your boat. That’s why

we build the smartest, toughest, most intuitive trolling motors on the water. Every aspect of a Minn Kota trolling motor is thought out

and rethought until it’s good enough to bear our name. Countless hours of research and testing provide you the Minn Kota advantage

that can truly take you “Anywhere. Anytime.” We don’t believe in shortcuts. We are Minn Kota. And we are never done helping you

catch more ﬁsh.

REGISTRATION

Remember to keep your receipt and immediately register

your trolling motor. A registration card is included with your

motor or you can complete registration on our website at

minnkotamotors.com.

SERIAL NUMBER

Your Minn Kota 11-character serial number is very important. It

helps to determine the speciﬁc model and year of manufacture.

When contacting Consumer Service or registering your product,

you will need to know your product’s serial number. We

recommend that you write the serial number down so that you

have it available for future reference.

MOTOR INFORMATION (For Consumer Reference Only)

Model:__________________________________________________________________________________________________________________

Serial Number: __________________________________________________________________________________________________________

Purchase Date: __________________________________________________________________________________________________________

Store Where Purchased:___________________________________________________________________________________________________

NOTICE: Do not return your Minn Kota motor to your retailer. Your retailer is not authorized to repair or replace this unit. You may

obtain service by: calling Minn Kota at (800) 227-6433; returning your motor to the Minn Kota Factory Service Center; sending

or taking your motor to any Minn Kota authorized service center. A list of authorized service centers is available on our website, at

minnkotamotors.com. Please include proof of purchase, serial number and purchase date for warranty service with any of the above

options.

minnkotamotors.com | 3

SAFETY CONSIDERATIONS

Please thoroughly read the user manual. Follow all instructions and heed all safety and cautionary notices. Use of this motor is only

permitted for persons that have read and understood these user instructions. Minors may use this motor only under adult supervision.

WARNING

You are responsible for the safe and prudent operation of your vessel. We have designed your Minn Kota product to be an accurate

and reliable tool that will enhance boat operation and improve your ability to catch ﬁsh. This product does not relieve you from the

responsibility for safe operation of your boat. You must avoid hazards to navigation and always maintain a permanent watch so you can

respond to situations as they develop. You must always be prepared to regain manual control of your boat. Learn to operate your Minn

Kota product in an area free from hazards and obstacles.

WARNING

Never run the motor out of the water, as this may result in injuries from the rotating propeller. The motor should be disconnected from

the power source when it is not in use or is off the water. When connecting the power-supply cables of the motor to the battery, ensure

that they are not kinked or subject to chafe and route them in such a way that persons cannot trip over them. Before using the motor

make sure that the insulation of the power cables is not damaged. Disregarding these safety precautions may result in electric shorts

of battery(s) and/or motor. Always disconnect motor from battery(s) before cleaning or checking the propeller. Avoid submerging the

complete motor as water may enter the lower unit through control head and shaft. If the motor is used while water is present in the

lower unit considerable damage to the motor can occur. This damage will not be covered by warranty.

WARNING

Take care that neither you nor other persons approach the turning propeller too closely, neither with body parts nor with objects.

The motor is powerful and may endanger or injure you or others. While the motor is running watch out for persons swimming and for

ﬂoating objects. Persons who lack the ability to run the motor or whose reactions are impaired by alcohol, drugs, medication, or other

substances are not permitted to use this motor. This motor is not suitable for use in strong currents. The constant noise pressure level

of the motor during use is less than 70dB(A). The overall vibration level does not exceed 2,5 m/sec2.

WARNING

When stowing or deploying the motor, keep ﬁngers clear of all hinge and pivot points and all moving parts. In the event of unexpected

operation, remove power leads from the battery.

WARNING

It is recommended to only use Johnson Outdoors approved accessories with your Minn Kota motor. Using non-approved accessories

including to mount or control your motor may cause damage, unexpected motor operation and injury. Be sure to use the product and

approved accessories, including remotes, safely and in the manner directed to avoid accidental or unexpected motor operation. Keep

all factory installed parts in place including motor and accessory covers, enclosures and guards.

KNOW YOUR BOAT

Keel

Bow

Hull

Bow

Stern

Port

Port Starboard

Starboard

Gunwale

Transom

Inboard

Outboard

minnkotamotors.com | 5

INSTALLATION

INSTALLING THE FORTREX

Your new Fortrex comes with everything you’ll need to directly install it to the boat. This motor can be directly mounted to the boat or

coupled with a Minn Kota quick release bracket for ease of mounting and removal. For installation with a quick release bracket, refer

to the installation instructions provided with the bracket. For compatible quick release mounting bracket, please visit minnkotamotors.

com. To install the motor directly to the boat, please follow the instructions provided in this manual. Please review the parts list,

mounting considerations and tools needed for installation prior to getting started. For additional product support and to locate your

nearest dealer, please visit minnkotamotors.com.

Item /

Assembly Part # Description Qty.

3✖MOTOR ASSEMBLY 1

A2994887 INSTALLATION HARDWARE BAG ASSEMBLY 1

42263468 1/4 - 20 X 2.5" SS PPH SCREW 6

52263103 1/4 - 20 SS NYLOCK NUT 6

62261713 1/4 FLAT 18-8 SS WASHER 6

AA 1378132 80# THRUST PROP KIT 1

BB 1378160 112# THRUST PROP KIT 1

72341160 PROP-WW2 (4.5)W/ADP.RING 1

82091701 WASHER-PROP (LARGE) 1

92093101 NUT-PROP NYLOC,LG, MX101 3/8 SS 1

10 2262658 PIN-DRIVE 1" 3/16" S/S 1

B2991925 pBRACKET STABLZR ARM ASY (SUB) 1

11 22655100 BUMPER STABILIZER 1

12 2263624 STABILIZER ROD 1

13 2263107 NYLON HEX NUT 3/4 - 10 UNC 1

14 2281829 BRACKET 1

15 2260221 VINYL CAP 1

16 2223100 NUT 5/16-18 NYLOCS SS 2

17 2263422 BOLT 5/16-18 X 1" SS CAP SCREW 2

18 2281700 5/16 "ID X .457 OD HIGH COLLAR LOCK WASHER 2

20 2773806 STRAP, HOLD DOWN 1

C2994912 BAG ASSY, FORTREX MOUNT HDW 1

25 2283410 SCREW-1/4-20 X .500" PFH 2

26 2281710 SPACER, GAS SPRING, FORTREX 2

27 2282610 PIN, UPPER SHOCK 1

p2287110 INSTALLATION GUIDE, FORTREX 1

D2991650 MNT FW 80# 45”, 112#/HC 52” *80 LB 45”* *112 LB 52”* 1

E2991652 MNT ASM FTX FW 80# 52/62” *80 LB 52”* *80 LB 62”* 1

F2991653 MNT ASM FTX FW 112# 45” *112 LB 45”* 1

G2991654 MNT ASM FTX FW 112# 52” *112 LB 52”* 1

32 2211415 ÌCABLE-EXTENSION, PD/AP 110" *PRE-INSTALLED* 1

490507-2 âCABLE, ADP-INT MDI 14 M12-174" *PRE-INSTALLED* 1

32 C

INSTALLATION PARTS LIST

pNot shown on Parts Diagram.

✖This part is included in an assembly and cannot be ordered individually.

ÌOnly available with models factory installed with Universal Sonar.

âOnly available with models factory installed with Built-in MEGA Down Imaging.

pThe Bow-Mount Stabilizer Assembly is not required or included on the 80lb 45”

Fortrex.

ASSEMBLY OF MOTOR TO MOUNT

• #2 Phillips Screwdriver

• (2) #3 Phillips Screwdriver

• 1/4" Allen Wrench

• Drill

• 9/32" Drill Bit

• 7/16" Box End Wrench

• A person to help with

installation

• Torque Wrench

• File or Sandpaper

• Hack Saw

• Marker or Pencil

• 1/8" Flat Screwdriver

• 1/8" Allen Wrench

• Loctite

a. Place the Mount on an elevated, level surface such

as a workbench or the tailgate of a pickup. The

Mount, as removed from the box, should be in the

deployed position.

b. Remove the 5/16" Allen Screw and Lock Washer

from the Mount using the 1/4" Allen Wrench. The

5/16" Allen Screw is located on the opposite end

of the mount from the hinge that opens and closes

when the mount is stowed and deployed.

It is recommended that the motor be mounted as close to the keel or centerline of the boat

as possible. Make sure the area under the mounting location is clear to drill holes and install

nuts and washers. Make sure the motor rest is positioned far enough beyond the edge of the

boat. The motor must not encounter any obstructions as it is lowered into the water or raised

into the boat when stowed and deployed. Consider a quick release or adapter bracket with the

installation of your motor. To view a list of accessories, please visit minnkotamotors.com.

Assembly of Motor to Mount

Allen Screw with

Lock Washer

Mount

Deployed

Stowed

View accessories

available for your

trolling motor at

minnkotamotors.com.

MOUNTING CONSIDERATIONS

TOOLS AND RESOURCES REQUIRED

INSTALLATION

NOTICE: This motor weighs approximately 55 lbs.

We recommend having a second person help with

the installation.

End Links

Allen Screw

Safety

Latch

Lock Washer

Mount

minnkotamotors.com | 7

INSTALLING THE BOWGUARD

2c. Align the Keyways on the inside of the Bowguard

with the End Links on the Mount. Lower the motor

assembly straight down until seated.

d. Install the 5/16” Allen Screw and the Lock Washer

and tighten to 10-12 ft/lbs.

NOTICE: The 5/16” Allen Screw must be tight

when installed and periodically tightened to 10-

12 ft/lbs. This will allow the motor to be stowed

properly. Tighten the Allen Screw when the Mount

is in the deployed position.

Mount

Allen Screw

Lock Washer

Pull Grip and Rope

Keyways

Bowguard

During installation, it is recommended to mount the motor to the boat before installing the Gas Spring Pin. The Gas Spring Pin is installed

in the Gas Spring Cylinder. The Gas Spring Cylinder is located on the inside of the Outer Arm, which is a part of the Mount. At this point in

the installation, the Gas Spring Cylinder is not fully installed and may move around inside the Mount when stowing and deploying the motor.

The Gas Spring Cylinder can become damaged while deploying the motor and the damage will prevent the Lift-Assist feature from operating

correctly once fully assembled. Make sure that the Gas Spring Cylinder does not get damaged in the Mount.

WARNING

Carefully lower the Bowguard into place to avoid creating a

pinch point between the Bowguard and Mount.

Installing the Bowguard

INSTALLING THE BOWGUARD

d. The Mount can be installed on either the Port

or Starboard side of the boat based on personal

preference. Test the placement of the Hold-Down

Strap to be sure it can hold the Mount as placed.

The placement of the buckle on the Hold-Down

Strap either inboard or outboard is based on personal

preference. The hook and loop on the fastener should

be face down for the Hold-Down Strap to function.

Deck of Boat

Keel

Mount

Hold Down

Strap

Hold Down

Strap

a. Review the mounting considerations at the beginning

of the Installation section for proper placement.

Place the Mount as close to the centerline or keel of

the boat as possible, with the motor in the stowed

position, on the deck of the boat. Check

placement

with the motor in the stowed and deployed positions.

ITEM(S) NEEDED

#20 x 1

b. Stow the motor into the ﬂat position by pulling

the Pull Grip and Rope to disengage the latch bar,

allowing the motor to fold into the ﬂat position.

c. Place the Hold-Down Strap (Item #20) under the

base of the Mount Plate so that it is below the Mount

when placed.

CAUTION

The Gas Spring Cylinder can become damaged in the Mount

while stowing or deploying the motor because it is not yet

fully installed. Damage will prevent the Lift-Assist feature

from operating correctly once fully assembled. Make sure

that the Gas Spring Cylinder does not get damaged by

keeping it inside the Outer Arm of the Mount.

minnkotamotors.com | 9

INSTALLING THE BOWGUARD

NOTICE: If Pattern 2 is used, the right side plate

must be removed to access the mounting holes in the

base of the Mount.

e. Check the placement with the motor in the deployed

position. When the motor is in the deployed position,

make sure that the Shaft is 1-1/2" out past the

Gunwale of the boat. The lower unit, when stowed

and deployed must not encounter any obstructions.

f. Check the placement of the Hold-Down Strap when

the motor is in the stowed and deployed position and

adjust if necessary.

1-1/2"

Minimum

Gunwale Shaft

Pattern 1

Pattern 2

Bow

Hold Down Strap

g. Once the Mount is in position, determine which bolt

pattern to use. The bolt pattern selected will depend

on the deck space available on your boat.

h. It is recommended to mark at least 4 of the 6 holes

in the base of the Mount and to have two bolts on

each side that are located the farthest apart on the

Mount Plate. Ideal installation would allow for 6

bolts to be used, with a minimum of 4.

i. Drill through the deck of the boat using a 9/32" Drill

Bit on the marked locations.

j. Be sure the Hold-Down Strap under the base of the

Mount Plate sits between the second and third set

of bolts according to the mounting pattern selected.

Double check that it can close around the Mount

when stowed.

WARNING

For installation, do not remove the shaft/motor from the

Bowguard. The Bowguard spring is under tension and must

always remain secured.

WARNING

When the motor is being transported, on water or land, it is

important to place the motor completely out of water. The

motor should be positioned up close to the Bowguard. Always

secure the Depth Collar Knob for added security during

transport and then secure the Hold Down Strap. This provides a

secure stow and holds the motor in place during transportation

when it is subject to high levels of shock and vibration. Failure

to secure the motor may result in injury or damage to the unit.

INSTALLING THE GAS SPRING PIN

a. Position the motor to the stowed position with the

Pull Grip and Rope to disengage the latch bar,

allowing the motor to fold into a ﬂat position.

b. Once in the stowed or ﬂat position, the Gas Spring

Pin and Spacers can be installed.

Gas Spring Cylinder

Proper Alignment

Outer Arm

k. Put a 1/4-20 x 2 1/2" Screw (Item #4) in each of the

drilled locations. The Screw should pass through the

Mount Plate and the boat deck.

l. Place a Flat Washer (Item #5) and then a Nylock Nut

(Item #6) at the end of each screw as shown and

secure. Make sure all hardware is secure.

ITEM(S) NEEDED

#5 x 6

Screw

Deck

Flat Washer

Nylock Nut

#6 x 6 #4 x 6

NOTICE: To prevent seizing of the stainless steel

hardware, do not use high speed installation tools.

Wetting the screws or applying an anti-seize may

help prevent seizing. If possible, secure all sets of

mounting bolts, nuts and washers.

Installing the Gas Spring Pin

WARNING

The gas assist lift mechanism in this unit is under high spring pressure when the motor is in the deployed position. Do not remove

the Bowguard from the mount without disconnecting one end of the gas spring. Failure to do this can create a condition where

accidental pulling of the Pull Grip and Rope may cause the mount to spring open rapidly, striking anyone or anything in the direct

path.

Autres manuels pour FORTREX

Table des matières

Langues :

Autres manuels MINN KOTA Moteur

MINN KOTA

MINN KOTA EDGE 30 Manuel utilisateur

MINN KOTA

MINN KOTA Riptide Ulterra Manuel utilisateur

MINN KOTA

MINN KOTA EDGE Manuel utilisateur

MINN KOTA

MINN KOTA RIPTIDE TERROVA Manuel utilisateur

MINN KOTA

MINN KOTA ULTERRA Manuel utilisateur

MINN KOTA

MINN KOTA TRAXXIS Manuel utilisateur

MINN KOTA

MINN KOTA MKA 32 QRB Manuel utilisateur

MINN KOTA

MINN KOTA ULTERRA Manuel utilisateur

MINN KOTA

MINN KOTA ULTREX Manuel utilisateur

MINN KOTA

MINN KOTA RIPTIDE INSTINCT QUEST Manuel utilisateur

MINN KOTA

MINN KOTA ULTERRA Manuel utilisateur

MINN KOTA

MINN KOTA 1810244 Manuel utilisateur

MINN KOTA

MINN KOTA Endura 50 Manuel utilisateur

MINN KOTA

MINN KOTA MAXXUM Series Manuel utilisateur

MINN KOTA

MINN KOTA RIPTIDE TERROVA Manuel utilisateur

MINN KOTA

MINN KOTA RIPTIDE POWERDRIVE Manuel utilisateur

MINN KOTA

MINN KOTA VANTAGE Manuel utilisateur

MINN KOTA

MINN KOTA TERROVA Manuel utilisateur

MINN KOTA

MINN KOTA RIPTIDE TERROVA 1363707 Manuel utilisateur

MINN KOTA

MINN KOTA Riptide 80 ST Manuel utilisateur

MINN KOTA

MINN KOTA RIPTIDE TERROVA Manuel utilisateur

MINN KOTA

MINN KOTA ULTERRA QUEST Manuel utilisateur

MINN KOTA

MINN KOTA ULTERRA Guide de dépannage

MINN KOTA

MINN KOTA EO 1/2 HP Manuel utilisateur

Manuels Moteur populaires d'autres marques

Rotax

Rotax 125 senior MAX evo Manuel utilisateur

Kohler

Kohler K361 Manuel utilisateur

MTD

MTD OHV Series Manuel utilisateur

Kohler

Kohler COMMAND CH18-745 Manuel utilisateur

Mercury

Mercury D4.2L D-Tronic Manuel utilisateur

Selve

Selve SE Plus-RC Series Manuel utilisateur

Perkins

Perkins 1206E-E66TA Manuel utilisateur

Skov

Skov DA 174 Manuel

Rossi

Rossi TX11 Series Manuel utilisateur

Siemens

Siemens SIMOTICS T-1FW3 Feuille d'instructions

AL-KO

AL-KO PRO 350 Manuel utilisateur

MTU

MTU 12 V 4000 Lx4 Manuel utilisateur

Nanni

Nanni N3.30 Manuel d'instructions

Nanni

Nanni N5.160 CR2 Manuel utilisateur

KSB

KSB SuPreme Series Instructions d'installation

Hiwin

Hiwin EM1 Series Manuel utilisateur

Rotax

Rotax 912 i series Mode d'emploi

Siemens

Siemens SIMOTICS XP 1MB1 Manuel utilisateur