Minebea TMHSAD-01 Manuel utilisateur
TORQUE TRANSDUCER
CALIBRATION SOFTWARE
TMHSAD-01
Instruction Manual
EN294-1799
I
Introduction
Thank you for purchasing our TMHSA series Torque Transducer.
This instruction manual describes how to operate the device, as well as noteworthy points.
Note that handling or operating the device incorrectly may result in malfunctions. Read this
manual thoroughly before use for safety and optimal results.
Keep this instruction manual in a location where it is readily accessible to end users.
Please note that this instruction manual is intended for use by engineers.
Disclaimers
The details contained in this instruction manual are subject to change without notice due to
product improvements.
While every care has been taken in the preparation of this instruction manual, it may not be
possible to correct errors or omissions immediately.
This instruction manual is copyrighted by our company. It may not be reproduced in part or in
whole without our express permission.
Scope of Software License
“The software” refers to the TMHSAD-01 software and its accompanying documentation,
including the instruction manual.
A copy may not be retained if all of the rights of the software are transferred. Any transfer of
the software (including all component parts, media, and documentation) shall be under the
condition of agreement by the recipient to the scope of the license.
The software may not be rented, leased, copied, modified, adapted, reverse-engineered,
reverse-compiled, or reverse-assembled in part or in its entirety.
Likewise, such actions may not be performed by third parties.
II
Pictograms and Conventions Used in This Manual
This manual uses the following pictograms to indicate actions to avoid at all times, aspects
requiring caution, and other noteworthy matters.
Be sure to read the descriptions provided alongside these pictograms.
Warning
This indicates circumstances in which incorrect handling may result in death or serious injury to
users.
Avoid the actions described here at all times.
Caution
This indicates circumstances in which incorrect handling may result in injury to users or damage to
property.
This indicates operating or procedural precautions or restrictions.
Always read the details included here to avoid malfunctioning.
Safety Precautions
Please be sure to read this manual before attempting to use the equipment.
1. Precautions
Caution
Altering the settings while carrying out measurements using the equipment may result in incorrect
measurements, equipment malfunctions, and damage to peripheral equipment.
III
Revision History
Date
Manual No.
Revision Reason (Details)
April, 2018
DRW. No. EN294-1799
First edition
IV
Contents
Introduction.............................................................................................................................................................I
Disclaimers..............................................................................................................................................................I
Scope of Software License....................................................................................................................................I
Pictograms and Conventions Used in This Manual...........................................................................................II
Safety Precautions.................................................................................................................................................II
1. Precautions.................................................................................................................................................II
Revision History....................................................................................................................................................III
Contents................................................................................................................................................................IV
1. Overview..........................................................................................................................................................1
2. System Operating Requirements .................................................................................................................1
3. Usage Precautions.........................................................................................................................................1
4. Initial Setup.....................................................................................................................................................2
4-1. Installation...................................................................................................................................................2
4-2. USB Driver Installation................................................................................................................................5
4-2-1. Driver Installation Procedure ...................................................................................................5
5. Launching the Software.................................................................................................................................8
6. Communication Settings...............................................................................................................................9
6-1. Checking the COM Port..............................................................................................................................9
6-2. Setting the COM Port................................................................................................................................10
7. Calibration.....................................................................................................................................................12
7-1. What Is Calibration?..................................................................................................................................12
7-2. Calibration Procedure...............................................................................................................................12
7-3. Screen Description....................................................................................................................................13
7-4. Calibration Procedure...............................................................................................................................14
8. Electrical Calibration....................................................................................................................................16
8-1. What Is Electrical Calibration?..................................................................................................................16
8-2. Screen Description....................................................................................................................................16
8-3. Calibration Procedure...............................................................................................................................18
8-4. Adjusting Voltage Output ..........................................................................................................................19
9. Parameter Settings.......................................................................................................................................20
9-1. Screen Description....................................................................................................................................20
9-2. Reading Setting Parameters.....................................................................................................................21
9-3. Writing Setting Parameters.......................................................................................................................22
9-4. Setting Parameter List ..............................................................................................................................23
9-5. Writing Calibration Data............................................................................................................................24
9-6. Saving Files...............................................................................................................................................25
9-7. Loading Files.............................................................................................................................................26
10. Monitor ..........................................................................................................................................................27
10-1. Screen Description....................................................................................................................................27
10-2. Start Communication ................................................................................................................................28
10-3. Stop Communication.................................................................................................................................28
10-4. Torque AD Value .......................................................................................................................................28
10-5. Wave Height Value....................................................................................................................................28
10-6. A/Z.............................................................................................................................................................29
10-7. CHECK......................................................................................................................................................29
11. Language selection......................................................................................................................................30
1
1.Overview
The calibration software transfers commands between TMHSAand a PC and allows users to read
TMHSA setting parameter data or write setting parameters as needed.
2.System Operating Requirements
PC
Operating system
Windows® 7, Windows® 8.0, Windows® 8.1, Windows® 10
CPU
Intel® Pentium® (Dual Core or Single Core) processor
Clock speed 2 GHz or higher
Minimum working memory
2 GB or more
Hard disk drive
Free space 1 GB or more
CD-ROM drive
DVD drive also acceptable (Required for setup)
Available USB ports
×1 (Required for USB cable communication)
Minimum resolution
1,280 × 1,024
3.Usage Precautions
Never turn off the TMHSA power or disconnect the USB cable while reading or writing setting
parameters to or from the TMHSA.
If this happens, do not leave the system as is after being shut down in the middle of reading or writing;
instead, restore the system to normal operation before resuming reading or writing.
2
4.Initial Setup
This section describes installation procedures before using the TMHSAD-01 calibration software
for the first time.
4-1. Installation
Install TMHSAD-01 on the PC to be used as follows.
(1) Insert the TMHSAD-01 setup disc (CD-ROM) into the PC.
(2) The [AutoPlay] screen appears.
If this does not happen automatically, open the CD-ROM in Windows Explorer or File Explorer and
double-click [TMHSAD-01_English.msi] in the [Setup] > [Setup_English] folder.
(3) The [Setup Wizard] screen appears automatically after the [Windows Installer Dialog] is displayed.
Click [Next].
Table des matières
Autres manuels Minebea Transducteur
Manuels Transducteur populaires d'autres marques
Mianyang Weibo Electronic
Mianyang Weibo Electronic WB Series Manuel utilisateur
ProMinent
ProMinent Dulcometer DMT Manuel utilisateur
MKS
MKS MicroPirani 925 Series Comment utiliser
WIKA
WIKA WU-20 Manuel utilisateur
Alcatel Vacuum Technology
Alcatel Vacuum Technology BARATRON 622A Manuel utilisateur
Camille Bauer
Camille Bauer SIRAX CH-5610 Manuel utilisateur
