Minarik VFDP4X04-D230-PCM Manuel utilisateur

850

[

]

.350

[

161

]

7.200

[

183

]

5.625

[

143

]

PEE

FWD

REV

JUS

TABLE

PEE

REVERSING

AC MOTOR CONTROL

M PLAT

2.2

[

55.9

]

[

86.4

]

0.73

[

18.5

]

IT H

2 PLA

ALL DIMENSI

NS IN INCHES

[

MILLIMETERS

]

4.56

[

116

]

2.12

[

53.8

]

Variable Frequency Drive for

3-phase & single phase AC motors

QUICK START GUIDE

VFDP4X04-D230-PCM

DIMENSIONS

SPECIFICATIONS

1-Phase Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .* 115/230 VAC

1 or 3 -Phase Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230 VAC

Maximum Horsepower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 HP

Maximum Continuous Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.0 AC

AC Amps In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 / 10 amps

AC Voltage Input Range . . . . . . . . . . . . . .115/230 VAC ± 10%, 50/60 Hz single phase

Standard Carrier Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 KHz

Adjustable Braking Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0 - 4 ADC

Adjustable Braking Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 - 10 Sec.

Adjustable Minimum Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0 - 30 Hz

Output Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0 - 120 Hz

Adjustable Maximum Output Frequency Range . . . . . . . . . . . . . . . . . . . . .30 - 120 Hz

Acceleration Time Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 - 12 secs

Deceleration Time Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 - 12 secs

Analog Input Voltage Range (S1 [-] to S2 [+]) . . . . . 0 - 5 VDC, 0 - 10 VDC, 4 - 20 mA

Input Impedance, S1 to S2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .~ 100K ohms

Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.5G max (20 - 50 Hz)

0.1G max (> 50 Hz)

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.2 lbs

Ambient Operating Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . .10° - 40° C

* Jumper settings MUST

match input line voltage.

Application of 230 VAC

line input when jumpers

are set for 115 VAC will

result in severe damage

to the drive.

1. Remove the six (6) phillips screws on the

front case.

NOTE: The two shorter screws (#6 - 32 x 2

1/2) on the front case are used at hole

locations 5 & 6.

2. Remove the five (5) phillips screws on the

bottom plate.

NOTE: DO NOT REMOVE the three (3)

screws securing the bottom plate to the

heatsink.

PEE

FWD

REV

ADJUSTABLE SPEED

REVERSING

AC MOTOR CONTROL

M PLAT

T REM

THE THREE

(

)

SCREWS SECURIN

THE B

M PLATE T

THE HEAT

REMOVING THE

CASE COVER

STEP #4

Configure jumpers JMP501 and JMP502 on the bottom board for 115 or 230 VAC Power Input.

502

501

STEP #2

Configure jumpers JMP504 and JMP505 on the top board for the appropriate signal input.

1 2

505

1 2

505

JMP504 (on top board)

Pins 1 & 2 for Voltage Input, or using a speed pot.

Pins 2 & 3 for Current Input

JMP505 (on top board)

Pins in Column 1 for 0 - 5 VDC Voltage Input,

or using a speed pot

Pins in Column 2 for 0 - 10 VDC Voltage Input

Pins in Column 3 for 4 - 20 mA Current Input exam

STEP #3

Configure jumpers JMP503 on the bottom board and JMP506 on the top board.

503

JMP503 (on bottom board)

Pins 1 & 2 to Trip

Pins 2

3 to Restar

TRIP: Drive has a low volta

e fault & mus

be manuall

re-enabled to restart

RESTART: Drive has a low volta

e fault

will momentaril

stop then auto-restar

when input volta

e returns to minimum level

V TRIP

TAR

506

JMP506 (on top board)

Pins 1 & 2 to Brake

Pins 2 & 3 to Coast

BRAKE

CONNECTIONS

STEP #5

Connect motor leads of a 3-

phase motor to U, V, and W

(TB502 on BOTTOM board)

using 14 - 16 AWG wire as

shown in the figure below.

STEP #6

Connect 115 or 230 VAC power

input using 12 AWG wire.

NOTE: Minarik strongly

recommends installing an

emergency stop switch on both

the L1 and L2 inputs.

STEP #1-skip this step if provided FWD/OFF/REV and speed potentiometer will be used.

Otherwise disconnect factory-wired connections from the FWD/OFF/REV switch and speed

potentiometer. Connect the enable/disable switch, direction switch, and speed potentiometer or

signal input to TB501 on the TOP board using 20 - 24 AWG wire as shown below.

DIRECTION

SWITCH

ENABLE/DISABLE

SWITCH

(open to disable)

NOTE:

The

actor

-wired spee

potentiometer on the

case cover must be

disconnected prior to

wirin

to a si

nal input

TO SPEED POT

OR SIGNAL INPUT

written permission from Minarik Corporation. The information and technical data in this document are subject to change without notice.

Minarik Corporation and its Divisions make no warranty of any kind with respect to this material, including, but not limited to, the implied

warranties of its merchantability and fitness for a given purpose. Minarik Corproation and its Divisions assume no responsibility for any errors

that may appear in this document and make no commitment to update or to keep current the information in this document. mvd092503

MINARIK DRIVES

www.minarikdrives.com

14300 De La Tour Drive, South Beloit, IL 61080; Phone: (800) MINARIK (646-2745); Fax: (815) 624-6960

Document Number: 250-0379, Revision 0; Printed in the U.S.A. - September 2003

Autres manuels Minarik Entraînement CC

Minarik

Minarik VFD Series Manuel utilisateur

Minarik

Minarik XP-AC-SL Series Manuel utilisateur

Minarik

Minarik DC30-12-4Q-L Manuel utilisateur

Minarik

Minarik C1XP02-115AC Manuel

Minarik

Minarik MM-PCM Series Manuel utilisateur

Minarik

Minarik M2 Manuel utilisateur

Minarik

Minarik Motor Master 20000 Series Manuel utilisateur

Minarik

Minarik PCM21000A Manuel utilisateur

Minarik

Minarik MMRG30U Manuel utilisateur

Minarik

Minarik HTL05-D-4Q Manuel utilisateur

Minarik

Minarik MMBOSS Series Manuel utilisateur

Minarik

Minarik MMRG Series Manuel utilisateur

Minarik

Minarik MM20000A Series Manuel utilisateur

Minarik

Minarik XP-AC Series Manuel utilisateur

Minarik

Minarik MM300 Series Manuel utilisateur

Minarik

Minarik MM20000 Series Manuel utilisateur

Minarik

Minarik BOSS Series Manuel utilisateur

Minarik

Minarik BOSS Series Manuel utilisateur

Minarik

Minarik PCM23000A Series Manuel utilisateur

Minarik

Minarik M2-D Manuel utilisateur

Minarik

Minarik RG500 Series Manuel utilisateur

Minarik

Minarik NRG-2Q Series Manuel utilisateur

Minarik

Minarik RG300 Series Manuel utilisateur

Minarik

Minarik NRGD-4Q Series Manuel utilisateur

Manuels Entraînement CC populaires d'autres marques

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manuel utilisateur

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manuel de la liste des pièces

Chamberlain Garog

Chamberlain Garog D Series Manuel utilisateur

Parker

Parker PDS Series Manuel utilisateur

Festo

Festo DGC G Series Guide de configuration

Binks

Binks QS-5012-1-CE Manuel utilisateur

Danfoss

Danfoss VLT 2800 Series Fiche technique

ABB

ABB ACQ580-01 Series Manuel d'installation

YASKAWA

YASKAWA CANopen SI-S3 Manuel utilisateur

GE D20A6 Manuel utilisateur

Unex

Unex MC-D-250-1000-050W-TW Manuel utilisateur

Geckodrive

Geckodrive G213V Manuel utilisateur

ABB

ABB RSYC-01 Manuel utilisateur

Rockwell Automation

Rockwell Automation PowerFlex 700S Manuel du propriétaire

WEG

WEG DeviceNet CFW500 Manuel utilisateur

Siemens

Siemens SINAMICS G Fiche technique

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Mode d'emploi

SOMFY

SOMFY JR RU 30 Manuel utilisateur