MIMAKI UJF-605R II Manuel utilisateur
MIMAKI ENGINEERING CO., LTD.
TKB Gotenyama Building, 5-9-41, Kitashinagawa, Shinagawa-ku, Tokyo 141-0001, Japan
Phone: +81-3-5420-8671 Fax: +81-3-5420-8687
URL: http: // www.mimaki. co. jp /
E-mail: [email protected]
Daily Care Manual
D201672
This inkjet printer is the precision machine that has highly delicate mechanism. Especially, dust and
paper powder may have effect on head nozzles firing ink, and may not get normal printing.
To use the inkjet printer in good condition, we recommend the following daily care.
2
Category of the Manuals
This printer attaches with the following manuals.
Setup Guide
The above manual describes setting procedure of
the printer.
Do not set up the printer by yourself. Setting up
should be conducted by your service engineer or the
electric contractor.
Operation Manual
The above manual describes operations of the
printer and daily maintenance.
Read this manual carefully and fully understand it to
use the printer.
Daily Care Manual
The above manual describes daily maintenance to
keep the printer in good condition.
3
Table of Contents
Category of the Manuals ......................................................................... 2
Routine Maintenance .............................................................................. 4
LOCAL Mode Display .............................................................................. 6
In Case Defective Printing is not Resolved ............................................. 7
Cleaning the Flushing Tray.................................................................... 11
When the Waste Ink Tank Becomes Full............................................... 13
Replacing the Water for the Water Heater ............................................ 14
Periodic Maintenance for the White Ink ................................................ 20
To prevent Ink Drop from Dripping during Printing [CARIG.CLEAN] .... 22
Storage of the Antifreezing Liquid and the Washing Liquid................... 26
Storage of Media ................................................................................... 26
Storage of the Ink Cartridges ................................................................ 26
4
Routine Maintenance
About use environment and care
•Use this printer in clean (less dust) environment. The use of a fan and a ventilator might
blow up dust around the printer.
•As using UV curing ink, install this printer in a well-ventilated area.
•Working environmental temperature is 15 to 30 °C (59 to 86 °F). Avoid using at lower or
higher than this.
Cautions during care
•Never disassemble the printer. Disassembling it causes electric shock and
failures of the printer.
•To prevent electric shock and failures to the printer, do not allow to get
inside moisture.
•Turn off power and detach power cable before doing any maintenance, or
unexpected accident may occur.
•Start maintenance after the UV lamp gets cool completely, or it may cause
burn injury.
•Benzene, thinner and chemical agents containing abrasives can deteriorate
or deform the surface of the cover.
•Do not apply lubricating oil or the like inside the printer. Such materials can
cause the printer mechanism to break down.
•UJF-605R is a printer that uses ultraviolet ray curing ink (UV ink). Make
sure to wear the supplied goggles and gloves during daily care.
•When water or alcohol are mixed into the ultraviolet ray curing ink(UV ink),
flocculation occurs. Be sure that water or alcohol do not adhere to not only
the nozzles but also near the heads, the caps, the suction nozzle and so
on.
5
Maintenance for the exterior and the table
If the exterior of the printer becomes dirty, wipe off the dirt with soft cloth moistened by
water or neutral detergent with water and squeezed. Wipe off dust on the table.
6
LOCAL Mode Display
The following describes the LOCAL mode display for each operation.
For maintenance, please enter the LOCAL mode by touching the [Leaf Print] on the touch
panel.
If entering the LOCAL mode by touching the [Roll Print], tension for media may work un-
necessarily.
STEPS:
1. Turn on the main power of the printer.
2. The opening screen is displayed.
3. Then, the top menu screen is switched
automatically.
4. Touch the [Leaf Print] to display the LO-
CAL mode for leaf media.
COPY
7
In Case Defective Printing is not Resolved
When the station interior is severely contaminated or defective printing is not resolved by
the head cleaning function ( Operation Manual P.2-28), clean the suction nozzle and
the caps with the cleaning kit as follows:
Washing liquid (SPC-0385), Gloves, Cleaning swab(SPC-0386), Goggles
•When cleaning the station and the heads, be sure to wear the supplied
goggles and gloves, or the ink may get in your eyes.
•Do not use alcohol or water.
•Do not move the carriage out of the capping station by hand. Use the
appropriate operation keys to move the carriage.
The examples of defective printing
These following examples indicate defective printings by using improper heads(nozzles)
caused by dust. Confirm the nozzle condition periodically before or during outputting not to
use in these condition. The nozzle condition can be confirmed by [test print] in this printer.
(Operation Manual P.2-27)
Deflection Nozzle out
Ink dropping Satellite
8
STEPS:
1. Touch the [FUNCTION] on the LOCAL
mode screen for leaf media.
2. Touch the JOG [ ] or [ ] to select the
[MAINTENANCE].
3. Touch the [ENTER].
4. Touch the JOG [ ] or [ ] to select the
[STATION].
5. Touch the [ENTER].
6. Touch the [ENTER].
The carriage moves to the table.
7. Open the right maintenance cover.
•When opening the cover, make sure
to hold the cover with the holding bar.
Otherwise the cover way fall down
and it may cause some injuries.
Holding bar
<< LOCAL >>
STATION
CARRIAGE OUT : ent
MAINTENANCE
STATION < ent >
MAINTENANCE
LIST < ent >
FUNCTION
MAINTENANCE < ENT >
FUNCTION
DATA CLEAR < ENT >
9
8. Clean the suction nozzle with the exclu-
sive cleaning swab moistened by the
washing liquid.
•Carefully clean the suction nozzle.
•Replace the suctions nozzle that is
severely contaminated or bent. Con-
tact your nearest sales agency or
MIMAKI sales office.
•Contact your nearest sales agency or
Mimaki sales office to order additional
cleaning swabs.
9. Wipe off the adherent ink which got on the
cap rubber or inside the suction nozzle
cover with the exclusive cleaning swab.
10. Close the right maintenance cover and then
touch the [ENTER].
The initial operation is performed, then the printer
returns to the LOCAL mode.
Suction nozzle cover
STATION
COMPLETED : ent
PLEASE WAIT
<< LOCAL >>
10
How to recover improper nozzle firing
When not using this printer for a long time or according to environmental temperature, the
nozzles may be unstable in firing.
In this case, follow procedures below to recover the nozzles.
In case the nozzles do not recover after implementing these procedures, contact with our
customer service or the agency you purchased, and need to replace the heads and so on.
1. Daily care
Implement all parts described in this manual.
2. Normal cleaning ( Operation Manual
P.2-28)
Implement normal cleaning along the operation
manual after daily care above-mentioned.
Repeat cleaning and test printing, and confirm the
nozzles are not clogging.
•In case nozzle clogging is not recov-
ered in spite of through all these
procedures, contact with our customer
service or make a service call to the
agency you purchased.
Abnormal pattern
Table des matières
Autres manuels MIMAKI Imprimante
MIMAKI
MIMAKI JV33 Series Manuel utilisateur
MIMAKI
MIMAKI TxF150-75 Manuel d'entretien
MIMAKI
MIMAKI UJV100-160 Manuel utilisateur
MIMAKI
MIMAKI JV33-260 Instructions de montage
MIMAKI
MIMAKI TS34-1800A Manuel utilisateur
MIMAKI
MIMAKI JV34-260 Manuel utilisateur
MIMAKI
MIMAKI UJV55-320 CMYK Manuel utilisateur
MIMAKI
MIMAKI CJV30-60 Manuel utilisateur
MIMAKI
MIMAKI UJV100-160 Instructions d'installation
MIMAKI
MIMAKI UJF-3042MkII e Manuel d'entretien
MIMAKI
MIMAKI JV5 Series Manuel utilisateur
MIMAKI
MIMAKI UCJV300-75 Manuel utilisateur
MIMAKI
MIMAKI ML Tiger-1800B MKII Manuel utilisateur
MIMAKI
MIMAKI UCJV300/150 Manuel utilisateur
MIMAKI
MIMAKI JV33-130BS Instructions de montage
MIMAKI
MIMAKI UJF-7151 plus Manuel d'entretien
MIMAKI
MIMAKI SIJ-320UV Manuel utilisateur
MIMAKI
MIMAKI JFX550-2513 Manuel d'entretien
MIMAKI
MIMAKI TS500P-3200 Manuel d'entretien
MIMAKI
MIMAKI TS5-1600AMF Manuel utilisateur
