MIMAKI JFX 200-2513 Manuel

Make sure to wear the attached

goggles and glove when you work.

JFX200-2513 / JFX500-2131

Cleaning procedure of head nozzle

Only when the nozzle drop out doesn’t recover with cleaning, daily care and maintenance, please clean

the head nozzle following the procedure below.

Procedure

1. Remove the left side cover of

the machine.

Remove the screw and remove the

cover.

2. Move the carriage(head) to the maintenance space.

(1) Press the key in LOCAL.

(2) Press the key.

(3) Press to select [HEAD MAINT.].

(4) Press the key.

•

Before performing the maintenance, please make sure to attend the training by our engineers. Maintenance

without training may cause failure of the head.

• During maintenance, never rub the nozzles of the head. If rub the nozzle part, the water-repellent surface is

degraded and the head might need to be replaced.

Supply goods for cleaning

Nozzle swab (100) Cleaning stick (50) F200/LF200 Cleaning liquid

for maintenance (100mℓ)

No.SPC-0421 No.SPC-0527 No.SPC-0568

• Make sure to use designated supply goods for nozzle cleaning. Other cleaning goods may cause early

deterioration of the head.

• Head will move for maintenance, please be careful.

[JFX200] Remove the screws

at two positions.

[JFX500] Remove the screws

at four positions.

Cover

Cover

MAINT.

© 2016 MIMAKI ENGINEERING CO., LTD. M018365-00(D203018-10)-15042016

3. Wet a new “nozzle swab” or “clean stick” with the cleaning

solution.

Please wet enough the cleaning solution.

4. Clean the nozzle surface.

(1) Press the "nozzle swab" or "cleaning stick", absorbing cleaning liquid,

against nozzle surface softly for about 10 seconds.

(2) Perform the work (1) to the entire nozzle surface.

5. Press the key after the cleaning.

After initial operation, carriage (head) return to the original position.

Please close the cover.

6. Implement the cleaning [NORMAL].

Please operate with reference to Chapter 4 of the Operation Manual.

7. Perform test printing and check the print result.

Repeat the cleaning and test printing until the result becomes normal.

• Please do not reuse the used clean stick.

It may cause nozzle clogging.

• Please do not rub the nozzle surface and press down strongly

sponge part with your fingers. Nozzle surface is damaged, and it

may cause the discharging defects.

• Please do not re-use the clean stick which was used once. Always

use a new clean stick seconds.

Press softly for 10 seconds

Nozzle surface

KT

Autres manuels pour JFX 200-2513

5

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels MIMAKI Traceur

MIMAKI

MIMAKI JV33-260 Manuel utilisateur

MIMAKI

MIMAKI ME-300STII Manuel utilisateur

MIMAKI

MIMAKI TextileJet Tx2-1600 Series Manuel utilisateur

MIMAKI

MIMAKI CG-60AR Manuel utilisateur

MIMAKI

MIMAKI CFL-605RT Manuel utilisateur

MIMAKI

MIMAKI JV33 Series Instructions de montage

MIMAKI

MIMAKI JV400-SUV Series Manuel d'entretien

MIMAKI

MIMAKI CFL-605RT Manuel utilisateur

MIMAKI

MIMAKI CF2 Series Manuel utilisateur

MIMAKI

MIMAKI UCJV300 Guide de démarrage rapide

MIMAKI

MIMAKI CF2 Series Manuel utilisateur

MIMAKI

MIMAKI CF22-1225 Instructions d'installation

MIMAKI

MIMAKI CF3-1631 Manuel utilisateur

MIMAKI

MIMAKI CG-60SL Instructions de montage

MIMAKI

MIMAKI CG-60AR Instructions d'installation

MIMAKI

MIMAKI CJV150 series Manuel utilisateur

MIMAKI

MIMAKI TPC-1000 Manuel utilisateur

MIMAKI

MIMAKI CG-FX SERIES Manuel technique

MIMAKI

MIMAKI JFX200-2513EX Manuel d'entretien

MIMAKI

MIMAKI CG-75FXII Manuel utilisateur

MIMAKI

MIMAKI CG-60EX Manuel utilisateur

MIMAKI

MIMAKI CJV30 Series Manuel utilisateur

MIMAKI

MIMAKI TS500 Manuel utilisateur

MIMAKI

MIMAKI UJF-605C Instructions de montage

Manuels Traceur populaires d'autres marques

MUTOH

MUTOH Kona 760 Manuel utilisateur

HP

HP 7475a Manuel utilisateur

Vulcan-Hart

Vulcan-Hart FC-500VC Manuel utilisateur

Roland

Roland TrueVIS VG-640 Manuel du propriétaire

Furuno

Furuno RP-180 Manuel utilisateur

Roland

Roland VersaCamm SP-540V Manuel utilisateur

Ioline

Ioline Summit Manuel utilisateur

Summa

Summa S CLASS Manuel utilisateur

Gerber Technology

Gerber Technology GERBERplotter MP Series Manuel utilisateur

Furuno

Furuno RP-17 Manuel utilisateur

HP

HP 7470A Manuel utilisateur

SII

SII LP-1010 Manuel utilisateur

Great Computer

Great Computer JII-61 Manuel utilisateur

Roland

Roland VersaUv LEF - 12i Manuel utilisateur

Lectra

Lectra Alys 120 Manuel utilisateur

MUTOH

MUTOH Ultima SC-850D Manuel utilisateur

Skycut

Skycut D Series Manuel utilisateur

Commodore

Commodore 1520 Manuel utilisateur