MiLAN MIL-S2612 Manuel utilisateur

User’s Manual

MIL-S2612, 2-port 100BASE-FX Module (ST)

MIL-S2613, 2-port 100BASE-FX Module (SC)

MIL-S2614, 2-port 100BASE-FX Module (MT-RJ)

MIL-S2615, 2-port 100BASE-FX Module (VF-45)

MIL-S2622, 4-port 100BASE-FX Module (ST)

MIL-S2623, 4-port 100BASE-FX Module (SC)

MIL-S2624, 4-port 100BASE-FX Module (MT-RJ)

MIL-S2625, 4-port 100BASE-FX Module (VF-45)

MIL-S3630, 8-port 10/100BASE-TX Module (RJ-45)

MIL-S6603SX, 1-port 1000BASE-SX Module (SC)

MIL-S6603LX, 1-port 1000BASE-LX Module (SC)

1. 8 ports 10/100Base-TX Module

100

LK/ACT

FD/COL

MIL-S3630 2345678

Figure 1. Front Panel

When installed into a Switch hub, the 10/100Base-TX Module provides 8

10/100Mbps Switch ports which can connect to 10Mbps or 100Mbps hub or end

station.

1-1. 8 Ports 10/100Base-Tx Module Features

!8 10/100Base-TX N-Way Switch ports.

!Conforms to IEEE 802.3, IEEE 802.3u and IEEE 802.3x standards

!Store and forward switch architecture for abnormal packet filtering

!Support for half and full duplex on all ports

!Backplane up to 2.4Gbps

!2M memory Buffer support

!Automatic address learning with 12K address entry storage

!Filtering and forwarding rate of 14,880~148,800 packets per second

!DIP Switch for decision connection mode with other network devices

1-2. DIP Switch with Link Mode

The 8 port 10/100Base-TX module provides dip switch for 1 to 4 port to adjust link

mode with other network devices. Another 4 ports use auto-negotiation protocol

only. There are three type of link mode can be chosen, Auto-negotiation,

100Mbps/Full duplex and 10Mbps/Full duplex.

P o rt 1

P o rt 2

P o rt 3

P o rt 4

DIP Sw itc h fo r

P o rt 1 to P o rt 4

adjustable

ports

Auto-

negotiation

FullD uplex

100M

P o rt 5

P o rt 6

P o rt 7

P o rt 8

876

4321

10M

Port 1

Port 2 Port 4

Port 3

OFF

Figure 2. Dip switch location and mode settings

If you adjust to auto-negotiation, then the DIP for 100Mbps and 10Mbps is not

effective. If you adjust to Full duplex, then the DIP for 100Mbps and 10Mbps is

effective.

The following Table 1. lists the ports’ operating modes based on the DIP switch

position.

PORT 1 PORT 2 PORT3 PORT4

SW123 4 5678

ON Full 10M Full 10M Full 10M Full 10M

OFF Auto 100M Auto 100M Auto 100M Auto 100M

Table 1. 8 Ports 10/100Base-TX Module DIP switch functions

1-3. LED Descriptions

There are three LED indicators for each of the RJ-45 LAN connection ports. If

there is no connection to a port, the corresponding LED indicators are not lit.

•100Mps This LED indicator is green when the corresponding port is

connected to a 100Mbps device. This LED indicator is not lit when the

corresponding port is connected to a 10Mbps device.

•Link/Activity.This LED indicator is green when there is a connection secured

to a device (a link) to the corresponding port. The LED indicator blinks when

there is a transmission of data (activity) taking place at the corresponding port.

•Duplex Mode/Collision.This LED indicator is orange when the

corresponding port is operating in Full Duplex mode. When the corresponding

port is operating in Half Duplex, the LED indicator is not lit. When collisions

are occurring at the corresponding port, the LED indicator blinks.

2. Two ports 100Base-FX Fiber Module

TX TXRX RX

LK/ACT

FD/COL

MIL-S2612

Figure 3. 2 port 100Base-FX Module Front View

When installed into a Switch hub, this Module provides a 100Mbps Fast Ethernet

fiber port which can be used to:

"Connect the Switch to the backbone of your network; that is, to a basement

switch, hub or router

"Connect the Switch to a 100Mbps server or end-station

2-1. Two ports 100Base-FX Fiber Module Features

!Conforms to IEEE 802.3u Fast Ethernet standard

!Support for SC, ST, MT-RJ, VF-45 fiber connectors (optional)

!Supports half and full duplex modes via DIP switches

!Store-and-forward switch architecture for abnormal packet filtering

!2 switching 100Mbps Fiber Ethernet ports

!Backplane up to 2.4Gbps

!Automatic address learning with 12K address entry storage

!Filtering and forwarding rate of 148,800 packets per second

!100Base-FX uses 62.5/125 micron multi-mode fiber

2-2. DIP Switch with Link Mode

An ST/SC/MT-RJ/VF-45 connector provides the link to the multi-mode fiber

cabling or single-mode fiber cabling, and two LED indicators show the status of

the Module at-a glance. A DIP-switch sets the operating mode to half-duplex or

full-duplex (default).

P o rt 2

P o rt 1

DIP Sw itc h L o c a tion

FullDuplex

Half D u p lex

OFF

Figure 4. Dip switch location and mode settings

The following Table 2. lists the ports’ operating modes based on the DIP switch

position.

PORT 1 PORT 2

SW 1 2

ON Half-Duplex Half-Duplex

OFF Full-Duplex Full-Duplex

Table 2. Two ports 100Base-FX Fiber ModuleDIP switch functions

2-3. LED Descriptions

There are two LED indicators for each of the Fiber connection ports. If there is no

connection to a port, the corresponding LED indicators are not lit.

•Link/Activity. This LED indicator is green when there is a connection secured

to a device (a link) to the corresponding port. The LED indicator blinks when

there is a transmission of data (activity) taking place at the corresponding port.

•Duplex Mode/Collision. This LED indicator is orange when the

corresponding port is operating in Full Duplex mode. When the corresponding

port is operating in Half Duplex, the LED indicator is not lit. When collisions

are occurring at the corresponding port, the LED indicator blinks.

3. Four Ports 100Base-FX Fiber Module

4123

TXTX TX TX RXRX RX RX

LK/ACT

FD/COL

MIL-S2622

Figure 5. 4 port 100Base-TX/FX Front View

When installed into a Switch hub, this Module provides 4 x 100Mbps Fast

Ethernet fiber ports which can be used to:

"Connect the Switch to the backbone of your network; that is, to a basement

switch, hub or router.

"Connector the Switch to a 100Mbps server or end station.

3-1 Four ports 100Base-FX Fiber Module Feature

!Conforms to IEEE 802.3u Fast Ethernet standard

!Support SC, ST, MT-RJ, VF-45 fiber connector (optional)

!Support half and full duplex via DIP switches

!Store-and-forward switch architecture for abnormal packets filtering

!Backplane up to 2.4Gbps

!Automatic address learning with 12K address entry storage

!Filtering and forwarding rate 148,800 packets per second for 100Mbps

!100Base-FX uses 62.5/125 micron multi-mode fiber

3-2. DIP Switch with Link Mode

An ST/SC/MT-RJ/VF-45 connector provides the link to the multi-mode fiber

cabling or single-mode fiber cabling, and two LED indicators show the status of

the Module at-a glance. A DIP-switch sets the operating mode to half-duplex or

full-duplex (default).

P o rt 1

P o rt 3

P o rt 4

P o rt 2

DIP Sw itch Location

FullDuplex

Half D u p lex

OFF

Figure 6. Location and setting duplex mode

The following Table 3. lists the ports operating modes based on the DIP switch

position.

PORT 1 PORT 2 PORT3 PORT4

SW 1 2 3 4

ON Half-Duplex Half-Duplex Half-Duplex Half-Duplex

OFF Full-Duplex Full-Duplex Full-Duplex Full-Duplex

Table 3. Four ports 100Base-FX Fiber Module DIP switch functions

3-3. LED Descriptions