Miele DA 6690 D Manuel utilisateur
Installation Instructions
DA6690 D en - CA
Installation, repair and maintenance work should be performed by
a Miele authorized service technician in accordance with national
and local safety regulations and the provided installation instructions.
Installation
31
Before installation
Before installing the appliance,
read all of the information contained
in this chapter and also in the "IM‐
PORTANT SAFETY INSTRUCTIONS"
section.
Installation parts
4 screws, ¹/₄" x 4 ⁵/₁₆"
(7 x 110 mm) and
4 plugs, ³/₈" x 3 ¹/₈" (10 x 80 mm)
for securing the ventilation hood to the
ceiling (not for use in USA / CDN).
The screws and plugs are designed
for use in solid ceilings only.
Use different fasteners for other ceil‐
ing construction types. Make sure
that the ceiling can support the load.
4 extension piece holders
for aligning and securing the telescopic
chimney
4 screws M³/₁₆" x ⁵/₁₆"
(M4 x 8.5 mm)
for securing the extension piece hold‐
ers.
14 screws M³/₁₆" x ⁵/₁₆"
(M4 x 8 mm)
for securing the spacer frame and se‐
curing the hood to the installation
frame.
1 screw M³/₁₆" x ⁵/₈" (M4 x 16 mm)
for securing the chimney.
DUI 32 recirculation kit for recircula‐
tion mode
(not supplied, available as an optional
accessory). The kit includes a direc‐
tional unit, aluminum hose, and hose
clips.
Installation
32
Appliance dimensions
aMounting area for the exhaust ducting and power cable. In recirculation mode,
only the power cord is required.
bPossible height range for appliance in vented mode
cPossible height range for appliance in recirculation mode
dAlternative installation with spacer frame
eAir vent positioned at the top for recirculation
Installation
33
fA power cord is required to connect the hood to the socket in the ceiling. With
extraction mode flexible ducting is also required.
Exhaust connection 6" (150 mm)
Distance between cooktop and ventilation hood (S)
Provided a larger distance is not given by the manufacturer of the cooktop, fol‐
low the minimum safety distances between a cooktop and the bottom of the
hood.
Please also observe the information contained in the "IMPORTANT SAFETY IN‐
STRUCTIONS" section.
Minimum distance S
Cooking appliance Miele
appliance Non-Miele
appliance
Electric/Induction cooktop 24" (610 mm)
Electric grill, deep fat fryer (electric) 26" (660 mm)
Multi-burner gas cooktop
≤43,000 BTU/hr (12.6 W),
no burner >15,000 BTU/hr (4.5 kW).
26" (660 mm) 30" (760 mm)
Multi-burner gas cooktop
≤73,800 BTU/hr (21.6 W),
no burner >16,500 BTU/hr (4.8 kW)
30" (760 mm)
Multi-burner gas cooktop
>73,800 BTU/hr (21.6 W),
or one of the burners >16,500 BTU/hr (4.8 kW)
Not possible
Single-burner gas cooktop
≤20,500 BTU/hr (6 kW) 26" (660 mm) 30" (760 mm)
Single-burner gas cooktop
>20,500 BTU/hr (6 kW)
≤27,600 BTU/hr (8.1 kW)
30" (760 mm)
Single-burner gas cooktop
>27,600 BTU/hr (8.1 kW) Not possible
Installation
34
Installation recommendations
– We also recommend a distance of at
least 25 ¹/₂" (650 mm) above electric
cooktops to provide more workspace
and easier cooking under the hood.
– When selecting an installation height,
always take the user height into con‐
sideration. Users should have ample
space to work comfortably on the
cooktop and reach the ventilation
hood controls with ease.
– Please note that the greater the dis‐
tance from the cooktop, the less ef‐
fective the hood is at drawing in the
cooking vapors.
– To achieve optimal vapor extraction,
make sure that the hood covers the
cooktop. The hood should be posi‐
tioned centrally over the cooktop, not
to the side or rear.
– The cooktop should be no wider than
the hood. Preferably, it should be
narrower.
– The mounting area must be easily
accessible. The ventilation hood
should be easy to reach and disas‐
semble in case a service call is nec‐
essary. This should be taken into
consideration when planning the po‐
sition of cupboards, shelves, ceilings
or decorative elements in the vicinity
of the ventilation hood.
Structural support
The hood must be attached to rigid
structural framing that is supported
in its entirety by the ceiling joists, or
to the ceiling joists directly. Do not
attach the plate directly to the ceiling
with anchors, toggle bolts, etc.
Removing the protective film
The housing components are covered
by a protective film to prevent them
from becoming damaged during trans‐
port.
Please remove this film before instal‐
ling the housing components. It can
be peeled off easily without any addi‐
tional tools.
Installation
35
8 5/8"
220 mm
8 5/8"
220 mm
dai3435aus
Draw two intersecting lines on the
ceiling.
For vented mode:
– Place a section of the exhaust duct‐
ing in the ceiling and feed it down
through the cross-sectional area as
illustrated. Exhaust ducting of ap‐
prox. 27 ⁹/₁₆" (700 mm) length is re‐
quired between the ceiling and the
hood exhaust socket.
– Secure the exhaust ducting to the ex‐
haust socket, e.g. with a hose clip
(available as an optional accessory)
on flexible ducting.
Place the power cord and guide it
through the ceiling in the area shown.
A power cord approx. 27 ⁹/₁₆"
(700 mm) in length is required be‐
tween the ceiling and the hood con‐
nectors.
Installation
36
Use a knife to release the four
spacers and the two covers from the
spacer frame supplied.
Use the spacer frame as a drilling
template. Place it on the ceiling with
the arrows pointing forwards. Using
the notches, align the spacer frame
on the intersecting lines and make
pencil marks for the drill holes.
Drill four holes ³/₈" (10 mm), ap‐
prox. 4 ¹/₂" (115 mm) deep for the
plugs supplied.
Place the four plugs in the holes and
screw in the four screws so that they
protrude by approx. 1 ³/₁₆" (30 mm).
Installation
37
The spacer frame can be installed be‐
tween the chimney and the ceiling. This
creates a shadow which gives the illu‐
sion of a gap between the ceiling and
the chimney. This is useful if the ceiling
is not level or is uneven. The hood is
aligned vertically with the spacers sup‐
plied. Visual irregularities between the
chimney and the ceiling are then con‐
cealed by the shadow.
If you wish to install the hood with the
spacer frame, remove the four inserts
from the fixing holes.
Mount the spacer frame onto the in‐
stallation frame.
Installation
38
Hang the installation frame on the
four screws. The front of the frame is
marked with a "V".
If using the spacer frame, place the
two covers into the fixing holes.
Align the installation frame and se‐
cure it with the screws.
The spacers, which were removed
from the spacer frame at the start,
can be used to align the hood verti‐
cally.
Installation
39
Holding the installation frame secure‐
ly, remove the two fixing screws and
extend the installation frame to its
maximum length.
Replace the screws.
The directional unit from recirculation
kit DUI 32 (optional accessory) is instal‐
led for recirculation mode (RM):
Bend the four retaining tabs on the
installation frame outwards.
Place the power cord inside the in‐
stallation frame.
Fit the directional unit as shown, not‐
ing the marking on the front.
Bend the retaining tabs back and ap‐
prox. 45° inwards to hold the direc‐
tional unit in place.
Autres manuels pour DA 6690 D
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Miele hotte de ventilation
Miele
Miele KMR1124 G Manuel utilisateur
Miele
Miele DA 289-4 Manuel utilisateur
Miele
Miele DA 265-2 Instructions de montage
Miele
Miele DAR 1125 Manuel utilisateur
Miele
Miele DA 337 I Manuel utilisateur
Miele
Miele DA 216-2 EXT Manuel utilisateur
Miele
Miele DA 6996 W Manuel utilisateur
Miele
Miele DA 5190 W Manuel utilisateur
Miele
Miele DA 408 Manuel utilisateur
Miele
Miele DA 199-2 Fiche technique
Miele
Miele DA 289 Manuel utilisateur
Miele
Miele DA 3466 Manuel utilisateur
Miele
Miele DA 5341 D Manuel utilisateur
Miele
Miele PUR 88 W Manuel utilisateur
Miele
Miele DA 6708 D Manuel utilisateur
Miele
Miele DA 402 Manuel utilisateur
Miele
Miele DAD 4840 Manuel utilisateur
Miele
Miele DA 426-4 Fiche technique
Miele
Miele DA 7000 D Manuel utilisateur
Miele
Miele DA 2660 EXT Manuel utilisateur
