Midas Touch MTA-3080 Manuel utilisateur

MTA-3080

8" Risc-based IoT Terminal

User's Manual

Version 1.0

- II -

This page is intentionally left blank.

- i -

Revision History

Version

Release Time

Description

1.0

2015.11

Initial release

- ii -

This document contains proprietary information protected by copyright. No part

of this manual may be reproduced by any mechanical, electronic, or other

means in any form without prior written permission of the manufacturer.

Disclaimer

The information in this document is subject to change without prior notice in

order to improve the reliability, design and function. It does not represent a

commitment on the part of the manufacturer.

Under no circumstances will the manufacturer be liable for any direct, indirect,

special, incidental, or consequential damages arising from the use or inability

to use the product or documentation, even if advised of the possibility of such

damages.

About This Manual

This user’s manual provides the general information and installation

instructions for the product.The manual is meant for the experienced users

and integrators with hardware knowledge of personal computers. If you are not

sure about any description in this manual, consult your vendor before further

handling.

We recommend that you keep one copy of this manual for the quick reference

for any necessary maintenance in the future. Thank you for choosing Midas

Touch products.

- iii - 
 
 
Contents 
Contents 
 
Preface...........................................................................................................v 
Declaration of Conformity................................................................................... v 
CE............................................................................................................... v 
FCC Class B............................................................................................... v 
RoHS..........................................................................................................vi 
SVHC / REACH..........................................................................................vi 
Safety Symbols..................................................................................................vii 
Important Safety Instructions.............................................................................vii 
General Cleaning Tips...............................................................................................ix 
Cleaning Tools.....................................................................................................ix 
Recommended Cleaning Procedures......................................................... x 
Disposing of the Equipment................................................................................xi 
Additional Information & Technical Support .......................................................xii 
Warranty............................................................................................................xii 
Chapter 1 Introduction ................................................................................1 
1.1 Product Highlights......................................................................................... 2 
1.2 Package Contents ........................................................................................2 
1.3 Optional Accessories....................................................................................3 
1.4 Parts of the Device .......................................................................................4 
1.5 Dimensions...................................................................................................5 
1.6 Specifications ...............................................................................................6 
Chapter 2 Installation ..................................................................................8 
2.1 microSD Card Installation.............................................................................9 
2.2 Wi-Fi/Bluetooth Antenna Installation.............................................................9 
2.3 SIM Card and 3G/4G AntennaInstallation (Optional).................................10 
2.4 Power Connection ...................................................................................... 11 
2.4.1 Using the DC Terminal Block Connector.......................................... 11 
2.4.2 Using the Power Adapter (Optional) ................................................ 12 
2.5 GPS Mouse Connection (Optional)............................................................. 12 
2.6 Mounting the Device...................................................................................13 
2.7 Connector Pintouts.....................................................................................13 
2.7.1 PWPIN.............................................................................................13 
2.7.2 GPIO and CAN Bus.........................................................................13 
Chapter 3 Using the Device ......................................................................15 
3.1 Turning On/Off the Device..........................................................................16 
3.2 Home Screen.............................................................................................. 16 

- iv -

Contents

3.2.1 Using the Quick Settings Panel .......................................................18

3.3 Configurations ............................................................................................19

3.3.1 Configuring Your SIM Card (Optional) .............................................19

3.3.2 Enabling Wi-Fi and Connecting to a WLAN.....................................20

3.3.3 Enabling Bluetooth and Pairing with Bluetooth Device ....................20

3.3.4 Enabling the Ethernet Feature.........................................................22

3.3.5 Enabling Location Service (Optional)...............................................23

3.3.6 Enabling and Using the NFC Features (Optional)............................ 23

- v -

Preface

Declaration of Conformity

The CE symbol on your product indicates that it is in compliance with the

directives of the Union European (EU). A Certificate of Compliance is available

by contacting Technical Support.

This product has passed the CE test for environmental specifications when

shielded cables are used for external wiring.We recommend the use of

shielded cables. This kind of cable is available from Midas Touch. Please

contact your local supplier for ordering information.

FCC Class B

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference

that may cause undesired operation.

Any changes or modifications not expressly approved by the guarantee of this

device could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of

the following measures:

•Reorient or relocate the receivingantenna.

•Increase the separation between the equipment andreceiver.

- vi -

Preface

•Connect the equipment into an outlet on a circuit different from that to

which the receiver isconnected.

•Consult the dealer or an experienced radio/TV technician forhelp.

RoHS

Midas Touch, Inc. certifies that all components in its products are in

compliance and conform to the European Union’s Restriction of Use of

Hazardous Substances in Electrical and Electronic Equipment (RoHS)

Directive 2002/95/EC.

The above mentioned directive was published on 2/13/2003. The main purpose

of the directive is to prohibit the use of lead, mercury, cadmium, hexavalent

chromium, polybrominated biphenyls (PBB), and polybrominated diphenyl

ethers (PBDE) in electrical and electronic products. Member states of the EU

are to enforce by7/1/2006.

Midas Touch, Inc. hereby states that the listedproducts do not contain

unintentional additions of lead, mercury, hex chrome, PBB or PBDB that

exceed a maximum concentration value of 0.1% by weight or for cadmium

exceed 0.01% by weight, per homogenous material. Homogenous material

is defined as a substance or mixture of substances with uniform composition

(such as solders, resins, plating, etc.). Lead-free solder is used for all

terminations (Sn(96-96.5%), Ag(3.0-3.5%) and Cu(0.5%)).

SVHC / REACH

Tominimize the environmental impact and take more responsibility to the

earth we live,Midas Touch hereby confirms all products comply with the

restriction of SVHC (Substances of VeryHigh Concern) in (EC) 1907/2006

(REACH --Registration, Evaluation, Authorization, and Restriction of

Chemicals) regulated by the European Union.

All substances listed in SVHC < 0.1 % by weight (1000 ppm)

- vii -

Preface

Safety Symbols

This symbol of “CAUTION” indicates that there is a danger of injury to

the user or a risk of damage to the product, should warning notices be

disregarded.

This symbol indicates electrical warning.

Important Safety Instructions

Read these safety instructions carefully:

1. Read all cautions and warnings on theequipment.

2. Place this equipment on a reliable surface when installing. Dropping it or

letting it fall may causedamage

3. Make sure the correct voltage is connected to the equipment.

4. For pluggable equipment, the socket outlet should be near the equipment

and should be easilyaccessible.

5. Keep this equipment away from humidity.

6. Disconnect this equipment from the A/C outlet before cleaning it. Use a

moist cloth. Do not use liquid or sprayed detergent forcleaning.

7. Tofully disengage the power to the unit, please disconnect the power from

the ACoutlet.

8. Do not scratch or rub the screen with a hard object.

9. Never use any of the solvents, such as Thinner Spray-type cleaner, Wax,

Benzene, Abrasive cleaner, Acid or Alkaline solvent, on the display. Harsh

chemicals may cause damage to the cabinet and the touchsensor.

10. Remove dirt with a lightly moistened cloth and a mild solvent detergent.

Then wipe the cabinet with a soft drycloth.

11. The openings on the enclosure are for air convection and protect the

equipment from overheating. DO NOT COVER THEOPENINGS.

12. Position the power cord so that people cannot step on it. Do not place

anything over the powercord.

- viii -

Preface

13. If the equipment will not be used for a long time, disconnect it from the

power source to avoid damage by transientovervoltage.

14. Never pour any liquid into openings.This may cause fire or electrical

shock.

15. Never open the equipment. For safety reasons, the equipment shouldbe

opened only by qualified service personnel.

16. If one of the following situations arises, get the equipment checked by

service personnel:

a. The power cord or plug isdamaged.

b. Liquid has penetrated into the equipment.

c. The equipment has been exposed tomoisture.

d. The equipment does not work well, or you cannot get it to work

according to the user’s manual.

e. The equipment has been dropped ordamaged.

f. The equipment has obvious signs ofbreakage.

17. The sound pressure level at the operator’s position, according to IEC 704-

1:1982, is no more than70dB(A).

18. Keep this User’s Manual for laterreference.

19. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED

ENVIRONMENT WHERE THE STORAGE TEMPERATURE ISBELOW

-20°C (-4°F) OR ABOVE 85°C (185°F). THIS MAY DAMAGE THE

EQUIPMENT.

Autres manuels pour MTA-3080

Table des matières

Autres manuels Midas Touch Terminal tactile

Midas Touch

Midas Touch MTA-3080 Manuel utilisateur

Manuels Terminal tactile populaires d'autres marques

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manuel utilisateur

Ingenico

Ingenico AXIUM EX4000 Manuel utilisateur

Heisei Electronics

Heisei Electronics Q-POS 815 Manuel utilisateur

Amano

Amano MTX-15 Manuel utilisateur

FLOWBIRD

FLOWBIRD CWT Compact Touch Manuel utilisateur

Demco

Demco SP7 Manuel utilisateur

Lathem

Lathem PC600 Series Manuel utilisateur

Partner

Partner MF-2352 Manuel utilisateur

NCR

NCR RealPOS 7460-2 Manuel

Simrad

Simrad MS50 Instructions de montage

Unitech

Unitech MR350 MKII Guide de démarrage rapide

Jungheinrich

Jungheinrich WMT 210 Manuel utilisateur

Motorola

Motorola MTP850 Manuel utilisateur

YASKAWA

YASKAWA 62H-MDC0 Manuel utilisateur

MVG industries

MVG industries NeptuLink Manuel utilisateur

Price Industries Limited

Price Industries Limited FDC Manuel d'instructions

Honeywell

Honeywell TemaKey Manuel utilisateur

EBN

EBN BPC65-B-A16G Manuel utilisateur