MG R3S-YS4 Manuel utilisateur

EM-8939 Rev.2 P. 1 / 4

MG CO., LTD. www.mgco.jp

5-2-55 Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

INSTRUCTION MANUAL

DC CURRENT OUTPUT MODULE

(4 points, isolated, tension clamp terminal block) MODEL R3S-YS4

BEFORE USE ....

Thank you for choosing us. Before use, please check con-

tents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact our sales ofﬁce or representatives.

■PACKAGE INCLUDES:

DC current output module..................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■HOT SWAPPABLE MODULES

• Replacing the module does not affect other modules on

the same base. Thus, the module can be replaced while

the power is ON. However, replacing multiple modules

at once may greatly change live voltage levels. We highly

recommend to replace them one by one.

■GENERAL PRECAUTIONS

• DO NOT set the switches on the module while the power

is supplied. The switches are used only for maintenance

without the power.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■UNUSED OUTPUT CHANNEL

• Close across the unused output terminals or set unused

channels to “unused” with PC Conﬁgurator software

(model: R3CON).

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

INSTALLATION

Use the Installation Base (model: R3-BSx).

R3S-YS4

EM-8939 Rev.2 P. 2 / 4

MG CO., LTD. www.mgco.jp

5-2-55 Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

COMPONENT IDENTIFICATION

RUN LED

ERR LED

■ FRONT VIEW ■ SIDE VIEW

SW3

1Output

Hold

■STATUS INDICATOR LED

RUN indicator: Bi-color (red/green) LED;

Red when the bus A operates normally;

Green when the bus B operates normally;

Amber when both buses operate normally.

ERR indicator: Bi-color (red/green) LED;

Red with output abnormality;

Green in normal operating conditions.

■SIDE DIP SW

• Output Hold: SW31

SW OUTPUT HOLD

HOLD (*)OFF

SW3-1 OFF ON

(*) Factory setting

Note: Be sure to set unused SW3-2 through 3-4 to OFF.

PC CONFIGURATOR

With conﬁgurator software, settings shown below are available.

Refer to the software manual of R3CON for detailed operation.

■CHANNEL INDIVIDUAL SETTING

PARAMETER AVAILABLE RANGE DEFAULT SETTING

Zero Scale -32000 to +32000 0

Full Scale -32000 to +32000 10000

Zero Adjust -320.00 to +320.00 0.00

Full Adjust -32000 to +32000 1.0000

Unused 0: Enable

1: Disable

0: Enable

R3S-YS4

EM-8939 Rev.2 P. 3 / 4

MG CO., LTD. www.mgco.jp

5-2-55 Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■EXTERNAL DIMENSIONS unit: mm (inch)

130 (5.12)

27.5 (1.08) 109 (4.29)

120 (4.72)

POSITIONING

GUIDE

■CONNECTION DIAGRAM

INTERNAL BUS A

*1INTERNAL BUS B

Unused channels left open are equal to the wire breakdown,

which turns the red ERR LED on and sets a burnout flag at

the PLC or the host device.

Unused channels can be specified and set so on the PC

Configurator Software (model: R3CON) without needing to

short at the field terminals.

• Unused Output Channels

Close across the unused output terminals as shown below.

*1. For dual redundant communication.

*2. To

use shield line, connect it to SLD terminal and ground the terminal 20.

Note: Do not use void terminals.

INTERNAL POWER

–

OUTPUT 1

–

OUTPUT 2

–

OUTPUT 3

–

OUTPUT 4

OUTPUT 1

Cross-wire

OUTPUT 2

OUTPUT 3

OUTPUT 4

SLD

BUS CONNECTOR

R3S-YS4

EM-8939 Rev.2 P. 4 / 4

MG CO., LTD. www.mgco.jp

5-2-55 Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

WIRING INSTRUCTIONS

■APPLICABLE WIRE SIZE

• Solid: 0.2 to 1.0 mm2(0.55 to 1.12 dia.)

• Stranded: 0.2 to 1.5 mm2

(Tinning wire ends may cause contact failure and therefore

is not recommended.)

• Ferruled:

Unsheathed: 0.25 to 1.5 mm2

Sheathed: 0.25 to 0.75 mm2

• Expose wire conductors by 10 mm (0.39”).

Stripped length

10mm

■CONNECTION PROCEDURE

Insert the wire end until it comes to a full stop while push-

ing slot with the tip of a screw driver as shown below. Be

sure wire insulation is not inside the terminal.

Screw Driver

Power wire

OUTPUT PIN ASSIGNMENT

PIN No. FUNCTION

1 I1

2 COM1

3 NC

4 SLD

5 I2

6 COM2

7 NC

8 SLD

9 NC

10 NC

11 I3

12 COM3

13 NC

14 SLD

15 I4

16 COM4

17 NC

18 SLD

19 SLD

20 SLD

FUNCTIONS

■OUTPUT HOLD or OUTPUT OFF

In normal conditions, the module outputs the signal from

the preferred bus A.

When an error is detected, the output is switched to the

data from the bus B.

• Output Hold

If both are in error, the module holds the signal and stands

by until one of the communications recovers.

• Output OFF

If both are in error, the module outputs -15 % and stands by

until one of the communications recovers.

At the startup, it outputs -15 % until the communication is

established and normal data is received.

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur