Metra Electronics 99-7614 Manuel utilisateur
METRA - The World’s best kits ®metraonline.com
REV. 12/9/2016 INST99-7614
Installation instructions for part 99-7614
®
CAUTION!
All accessories, switches, climate controls panels, and
especially air bag indicator lights must be connected before cycling
the ignition. Also, do not remove the factory radio with the key in the
on position, or while the vehicle is running.
© COPYRIGHT 2016 METRA ELECTRONICS CORPORATION
• ISO DIN radio provision with pocket
• ISO DDIN radio provision
• A) Radio housing • B) Radio brackets (C) • C) ISO DDIN trimplate • D) (4) #8 x 3/8” Phillips screws
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-7552
Antenna Adapter: • 40-NI12
• Panel removal tool • Phillips screwdriver
TOOLS REQUIRED
Nissan NV 2012-2014, NV (without NAV) 2015-up,
Nissan Quest (without NAV or rear seat entertainment) 2011-2012
99-7614
Dash Disassembly
Nissan
– NV 2012-2014.................................................2-4
– NV 2015-up (without NAV) ...............................2-4
– Quest (without NAV or rear seat entertainment)
2011-2012......................................................5-6
Kit Assembly
– ISO DIN radio provision with pocket .................... 7
– ISO DDIN radio provision..................................... 7
Table of Contents
BA CD
99-7614
®
2
NV 2012-2014,
NV (without NAV) 2015-up
1. Unclip and remove the A/C vent to
the right side of the factory radio.
(Figure A)
2. Remove the (2) Phillips screws
exposed behind vent on radio trim
panel. (Figure B)
3. Unclip and remove the left A/C
vent next to the instrument display.
(Figure C)
4. Unclip the top edge of the knee
bolster panel below the steering
column and let hang. (Figure D)
Continued on the next page
(Figure A)
(Figure D)
(Figure B)
(Figure C)
Dash Disassembly
99-7614
®
5. Unclip the circle trim around the
key cylinder.
6. Unclip and remove the gauge
cluster trim panel. (Figure E)
7. Remove (2) Phillips screws
exposed behind the panel on the
left side of the radio trim panel.
(Figure F)
8. Unclip and remove the trim panel
surrounding the factory radio.
(Figure G)
9. Remove (4) Phillips screws
securing the radio. (Figure H)
3
(Figure F)
(Figure G)
(Figure H)
(Figure E)
Dash Disassembly (Cont)
99-7614
®
4
Dash Disassembly
(Figure B)
(Figure C)
(Figure D)
(Figure A)
Quest (without NAV or rear seat
entertainment) 2011-2012
1. Unclip and remove the panels from
the bottom left and right side of the
center console. (Figure A)
2. Remove (2) clips per side exposed
behind lower panels. (Figure B)
3. Unclip and pull center console
toward rear of vehicle.
Note: You do not have to fully
remove console. (Figure C)
4. Unclip and remove the trim panel
to the left of the shifter housing the
start/stop button. (Figure D)
5. Unclip and remove the panel on
the end of the passenger side of
the dash. (Figure E)
Continued on the next page
(Figure E)
99-7614
®
5
6. Remove (1) Phillips screw from the trim panel above
the glove box then unclip and remove the panel.
(Figure F)
7. Remove (1) Phillips screw from the cup holder panel
then unclip and remove the panel. (Figure G)
Continued on the next page
(Figure F)
(Figure G)
Dash Disassembly (Cont)
99-7614
®
6
8. Remove (2) Phillips screws from the a/c
control panel and unclip and let hang.
(Figure G)
9. Remove (2) Phillips screws from the bottom
of the radio trim panel including the vents
then unclip and remove
the panel. (Figure G)
10. Remove (4) Phillips screws securing
the radio. (Figure H)
(Figure G)
(Figure H)
Dash Disassembly (Cont)
99-7614
®
7
Kit Assembly
ISO DIN radio provision with pocket
1.
Remove the metal “DIN” sleeve and
trim ring from the aftermarket radio
.
2. Secure the radio brackets to the
radio housing using the (4) 3/8”
Phillips screws provided. (Figure A)
3. Slide the radio into the bracket/
housing assembly and secure
using the screws supplied with the
radio. (Figure B)
4. Locate the factory wiring harness
and antenna connector in the dash.
Metra recommends using the
proper mating adapters from Metra
and/or AXXESS.
5. Reassemble the dash in reverse
order of disassembly.
ISO DDIN radio provision
1. Remove the brackets from the
factory radio.
2. Secure the brackets to the
aftermarket radio using the screws
supplied with the aftermarket
radio. (Figure A)
Note: 99-7614 radio brackets can
be used in place of the factory
brackets.
3. Locate the factory wiring harness
and antenna connector in the
dash. Metra recommends using
the proper mating adapters from
Metra and/or AXXESS.
4. Place the ISO DDIN trim plate on
the front of the radio. (Figure B)
5. Reassemble the dash in reverse
order of disassembly.
(Figure A) (Figure A)
(Figure B) (Figure B)
METRA - The World’s best kits ®metraonline.com © COPYRIGHT 2016 METRA ELECTRONICS CORPORATION
REV. 12/9/2016 INST99-7614
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
Installation instructions for part 99-7614
®
IMPORTANT
If you are having difficulties with the
installation of this product, please call our
Tech Support line at 1-800-253-TECH.
Before doing so, look over the instructions a
second time, and make sure the installation
was performed exactly as the instructions
are stated. Please have the vehicle apart
and ready to perform troubleshooting steps
before calling.
METRA - The World’s best kits ®metraonline.com
REV. 12/9/2016 INST99-7614
Instrucciones de instalación para la pieza 99-7614
®
¡PRECAUCIÓN!
Todos los accesorios, interruptores, paneles de con-
troles de clima y especialmente las luces del indicador de las bolsas
de aire deben estar conectados antes ciclar la ignición. Además, no
quite el radio de fábrica con la llave en la posición o de encendido ni
con el vehículo funcionando.
© COPYRIGHT 2016 METRA ELECTRONICS CORPORATION
• Provisión de radio ISO DIN con bolsillo
• Provisión de radio ISO DDIN
• A) Carcasa del radio • B) Soportes de radio (C) • C) ISO DDIN placa de moldura • D) (4) #8 x 3/8” tornillos Phillips
CARACTERÍSTICAS DEL KIT
COMPONENTES DEL KIT
CABLEADO Y CONEXIONES DE ANTENA (se venden por separado)
Arnés de cableado: • 70-7552
Adaptador de antena: • 40-NI12
• Herramienta para quitar paneles • Destornillador Phillips
HERRAMIENTAS REQUERIDAS
Nissan NV 2012-2014, NV (sin NAV) 2015-up,
Nissan Quest (sin NAV o entretenimiento para el asiento trasero) 2011-2012
99-7614
Indice
BA CD
Desmontaje del tablero
Nissan
– NV 2012-2014.................................................2-4
– NV 2015-up (sin NAV)......................................2-4
– Quest (sin NAV o entretenimiento para el asiento
trasero) 2011-2012.........................................5-6
Ensamble del kit
– Provisión de radio ISO DIN con bolsillo................ 7
– Provisión de radio ISO DDIN................................ 7
99-7614
®
2
NV 2012-2014,
NV (sin NAV) 2015 y mas
1. Desenganche y quite la rejilla del
aire acondicionado que está a
la derecha del radio de fábrica.
(Figura A)
2. Quite los (2) tornillos Phillips que
quedan a la vista detrás de la
rejilla en el panel de moldura del
radio. (Figura B)
3. Desenganche y quite le rejilla
del aire acondicionado que está
a la izquierda de la pantalla de
instrumentos. (Figura C)
4. Desenganche el borde de arriba
del panel del refuerzo para
rodillas de abajo de la columna
de dirección y déjelo colgando.
(Figura D)
Continua en la siguiente pagina
(Figura A)
(Figura D)
(Figura B)
(Figura C)
Desmontaje del tablero
Table des matières
Langues :
Autres manuels Metra Electronics Support TV
Metra Electronics
Metra Electronics 95-3005 Manuel utilisateur
Metra Electronics
Metra Electronics 99-3022B Manuel utilisateur
Metra Electronics
Metra Electronics TX86 Manuel utilisateur
Metra Electronics
Metra Electronics 95-7802CH Manuel utilisateur
Metra Electronics
Metra Electronics TL64 Manuel utilisateur
Metra Electronics
Metra Electronics 95-8734 Manuel utilisateur
Metra Electronics
Metra Electronics 99-7367 Manuel utilisateur
Metra Electronics
Metra Electronics 107-GM3B Manuel utilisateur
Metra Electronics
Metra Electronics 108-FD9B Manuel utilisateur
Metra Electronics
Metra Electronics 95-7815B Instructions d'utilisation
Metra Electronics
Metra Electronics 99-5832G Manuel utilisateur
Metra Electronics
Metra Electronics 99-5831 Manuel utilisateur
Metra Electronics
Metra Electronics DP-7363B Manuel utilisateur
Metra Electronics
Metra Electronics 95-8910S Manuel utilisateur
Metra Electronics
Metra Electronics 99-5600 Manuel utilisateur
Metra Electronics
Metra Electronics 99-9223 Manuel utilisateur
Metra Electronics
Metra Electronics 99-5830B Manuel utilisateur
