Messoa UFD301 Manuel utilisateur

1MP/3MP Flat Mini Dome Network Camera

Quick Start Guide

1MP Fixed Lens Model

3MP Fixed Lens Model

201402 301.305 A1

Quick Start Guide

Table of Content

1. Product Overview 3

1.1 Physical Characteristics 3

2Installation and Connection 4

2.1 Package Content 4

2.2 Installation 4

2.2.1 Connecting the Wires 4

2.2.2 Disassembling the Camera 5

2.2.3 Installing the Camera 5

2.2.4 Adjusting the Position 6

2.2.5 Sticking Desiccant 7

2.2.6 Completing the Installation 7

3Connection 8

3.1 Network Topology 8

3.2 Accessing the Camera for the First Time 8

3.3 IP Finder 9

Quick Start Guide

WARNING

The 1MP Fixed Lens Model operates at PoE IEEE 802.3af Class 0.

The 3MP Fixed Lens Model operates at DC 12V/ PoE IEEE 802.3af Class 0.

Installation and service should be performed only by qualified and experienced technicians and comply

with all local codes and rules to maintain your warranty.

To reduce the risk of fire or electric shock, do not expose the product to rain or moisture.

Wipe the camera with a dry soft cloth. For tough stains, slightly apply with diluted neutral detergent and

wipe with a dry soft cloth.

Do not apply benzene or thinner to the camera, which may cause the surface of unit to be melted or lens

fogged.

Avoid aligning the lens to very bright objects (example, light fixtures) for long periods of time.

Avoid operating or storing the unit in the following locations:

Extremely humid, dusty, or hot/cold environments (recommended operating temperature: -40°C to +50°C )

Close to sources of powerful radio or TV transmitters

Close to fluorescent lamps or objects with reflections

Under unstable or flickering light sources

Compliance

This equipment complies with the requirements as listed below:

FCC Part 15 Class B

CE: EMC directive and General Product Safety Directive GPSD conforming to requirements of standards

EN55022 for emission, EN 55024 for immunity, EN 300 and EN 328 for WIFI.

WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product

(applicable in the European Union and other European countries with separate collection

systems). This product should be disposed of, at the end of its useful life, as per applicable

local laws, regulations, and procedures.

Quick Start Guide

1. Product Overview

1.1 Physical Characteristics

Figure 1 - 1: Pictorial index

Table 1 - 1: Pictorial Index Definition

Index # Name

1 Dome cover

2 Unit body

3 Micro SD card slot (3MP Fixed Lens Model Exclusive)

1MP Fixed Lens Model 3MP Fixed Lens Model

Quick Start Guide

2Installation and Connection

2.1 Package Content

Check everything in the packing box matches to the order form and the packing slip. In addition to this manual,

items below are included in the packing box.

Fixed flat dome camera x 1

Plastic Anchor x2

Flat Head Screw (Tapping Type) x2

Security Torx Wrench x1

Mounting Template x1

Printed quick installation guide x 1

Video Monitor Output Cable x1

CD containing the IP Finder, user manual, and quick installation guide x 1

Desiccant x1

Please contact your dealer if any item missing.

2.2 Installation

When first unboxing, please check whether if there is any visible damage to appearance of the unit and its

accessories. The protective materials used for the packaging should be able to protect the unit from most of

accidents during transportation. Please remove the protective materials of the unit when every item is

checked in accordance with the list in “2.1 Package Content”

2.2.1 Connecting the Wires

Connect the power cable to the power plugs with one of the following options.

DC 12V: (3MP Fixed Lens Model Exclusive) Connect 12V (－) to terminal =DC 12V－, and Connect

12V (＋) to terminal =DC 12V＋

PoE: Connect the RJ-45 jack to a PoE compatible network device that supplied power with

networking capability through the Ethernet cable.

Insert audio input/output cables to the connectors of unit if required (3MP Fixed Lens Model Exclusive).

Note Please carefully manage waterproof procedure prior to operating as the pigtail cable linked

with the unit is not fully waterproof for different applications.

Quick Start Guide

2.2.2 Disassembling the Camera

1. Loosen the 2 screws on the cover by the supplied torx wrench.

2. Remove the dome cover.

3. Insert the optional micro SD card for file storage if necessary ( ).

Figure 2 - 1: Disassembling the Camera

2.2.3 Installing the Camera

1. Attach the mounting template to the wall or ceiling.

2. Drill two holes indicated on the mounting surface and insert the plastic anchors into the holes.

3. Please drill another hole with Ø30mm in diameter as indicated on the mounting template in the wall or

ceiling and pass all the signal cables through the hole.

4. Secure the unit body to the wall or ceiling with the 2 flat head screws (tapping type).

1MP Fixed Lens Model 3MP Fixed Lens Model

3MP Fixed Lens Model Exclusive

Quick Start Guide

Figure 2 - 2: Installing the Camera

2.2.4 Adjusting the Position

1. Loosen the two screws beside the lens as figure below.

2. Adjust the lens to a desired shooting angle for suitable coverage.

Figure 2 - 3: Adjusting the Camera Position

Note Make sure to relock the 2 screws tightly after adjustment.

1. Mounting Template

2. Plastic Anchors x 2

3. Flat Head Screws

(Tapping Type) x 2

The lens can be adjusted vertically & horizontally

once the two screws are fully loosened.

Quick Start Guide

2.2.5 Sticking Desiccant

1. Take out the desiccant from the package.

2. Flip over the dome cover and stick desiccant to the rectangular recess as the figure shown below.

Figure 2 - 4: Sticking Desiccant

2.2.6 Completing the Installation

1. After mounting the unit body to the surface, attach the dome cover with extra care on direction.

2. Fasten the dome cover with unit body by securing screws tightly via torx wrench to complete installation.

Figure 2 - 5: Completing the Installation

Quick Start Guide

3Connection

3.1 Network Topology

The unit, which is equipped with Ethernet RJ-45 network interface, can deliver video images and audio in real

time via either Internet or Intranet. Please refer to the skeleton drawings shown below for understanding.

Figure 2 - 6: Network Topology

3.2 Accessing the Camera for the First Time

The camera comes with a web-based setup utility, allowing you to view the video of the camera and configure

the camera for optimal use in your environment. Take the following steps to connect your PC to the camera.

Step 1: Make the connection

For initial setup purposes, connect one end of an Ethernet cable to the RJ-45 connector of the camera and

the other end to the LAN port on your PC.

Step 2: Configure your PC’s IP address

The camera uses a default IP address of 192.168.1.30 and subnet mask of 255.255.255.0. To have your PC

on the same network with the camera, configure your PC’s IP settings as below:

IP address: 192.168.1.X, where X is a number between 2 to 254, excluding 30.

Subnet mask: 255.255.255.0.

Step 3: Link Verification between PC and Camera

1. Launch the Command Prompt by clicking the Start menu, Programs, Accessories and then Command

Prompt.

2. At the prompt window, type ping x.x.x.x, where x.x.x.x is the IP address of the camera (the default is

192.168.1.30). If the message of “Reply from…” responds, it means the connection is established.

Step 4: Accessing the Camera from IE Browser

Open the IE browser and enter the IP address of the camera in the URL field. The default is 192.168.1.30.

When prompted for login, enter the user name and the password (The defaults: admin, 1234). Note that the

user name and password are case-sensitive.

Quick Start Guide

3.3 IP Finder

IP Finder is a utility program that helps users to locate the unit in local area network that computer is

connected to. Please note that IP Finder works only in Microsoft Windows XP, Microsoft Windows Vista, and

Microsoft Windows 7.

To install the software, simple locate and double-click the IP Finder setup file on the provided CD. Then follow

the on-screen prompts to proceed.

After you launch IP Finder, the window would list information of units in operation at present, and user can

press FIND CAMERA to find more units. Locate and double-click one of the cameras in the list you want to

configure the network settings. Click Save to enable the settings and click Exit to exit the utility.

Figure 2 - 7: IP Camera Finder

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Messoa Caméra de sécurité

Messoa

Messoa SCB267-HN5 Manuel utilisateur

Messoa

Messoa NDF820 Manuel utilisateur

Messoa

Messoa NCB750 Manuel utilisateur

Messoa

Messoa LPR606 Manuel utilisateur

Messoa

Messoa NCB855E Manuel utilisateur

Messoa

Messoa NDR891 Manuel utilisateur

Messoa

Messoa PTZ900 Manuel utilisateur

Messoa

Messoa NCB855E Manuel utilisateur

Messoa

Messoa ZEIM-4000604G A.1 Manuel utilisateur

Messoa

Messoa NIC990 Manuel utilisateur

Messoa

Messoa NCC800 Manuel utilisateur

Messoa

Messoa NDR891PRO Manuel utilisateur

Messoa

Messoa NDF821 Manuel utilisateur

Messoa

Messoa SDF418 Manuel utilisateur

Messoa

Messoa NID318 Manuel utilisateur

Messoa

Messoa NOD316 Manuel utilisateur

Messoa

Messoa NOD316 Manuel utilisateur

Messoa

Messoa A101RZ Manuel utilisateur

Messoa

Messoa NCR875-HN5 Manuel utilisateur

Messoa

Messoa PTZ900 Manuel utilisateur

Messoa

Messoa NDF831-HN5 Manuel utilisateur

Messoa

Messoa NCB750 Manuel utilisateur

Messoa

Messoa NDR890-HN5 Manuel utilisateur

Messoa

Messoa LPR610 Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur