Messoa NDF820 Manuel utilisateur
www.messoa.com
2012-07 A1
Indoor Dome Camera
NDF820/NDF820E
Quick Start Guide
Guia de inicio rápido
Guida rapida
Guide de démarrage rapide
Краткое руководство
クイックスタートガイド
快速安裝指南
快速安装指南
NDF820/NDF820E l Quick Start Guide 1
English
Safety Instructions
Make sure the supplied voltage meets the power consumption
requirements of the camera before powering the camera on.
Incorrect voltage may cause damage to the camera.
The camera should be protected from water and moisture, excessive
heat, direct sunlight and cold.
This installation should be made by a qualied service person and
should conform to all local codes.
Unplug the camera during lightening storms or when unused for
long periods of time.
Copyright
No part of this document may be reproduced or transmitted in any form
or by any means, electronic or mechanical, for any purpose, without
the express written permission of MESSOA.
© 2012 All rights reserved.
Disclaimer
Specications and information contained in this document are
presented as accurately as possible as of the time of release, but
are not guaranteed to be entirely free of error. MESSOA assumes no
responsibility for errors or omissions that may appear in this document
and reserves the right to change this publication at any time without
obligation to notify anyone of such revisions or changes.
2 NDF820/NDF820E l Quick Start Guide
1. Introduction
1.1 Package Contents
Indoor Dome Camera x1
CD-ROM (User manual and IP Finder utility) x1
Quick Start Guide x1
Guide Pattern Sticker x1
RJ-45 Female / Female Coupler x1
Accessories
• Machine Type Flat Head Screw (#1) x4
• Tapping Type Flat Head Screw (#2) x4
• Plastic Anchor (#3) x4
• Rubber Foot (#4) x4
123 4
NDF820/NDF820E l Quick Start Guide 3
English
1.2 Hardware Overview
Connectors
1
2
3
1. PowerIn(Red+/Black-): power connector, DC12V/AC24V
2. RJ-45EthernetConnector: network & PoE (Power over Ethernet)
connection
3. BNC: composite video output
4 NDF820/NDF820E l Quick Start Guide
2. Installation
2.1 Mounting the Camera
This camera is designed for ceiling & wall mounts depending on users
requirements. Mount the camera to your intended location.
Disassembling
1. Take off the dome cover screw.
2. Rotate the dome cover counterclockwise to unlock and pull free of
the housing.
3. Then remove the inner liner by gently pulling it free of the two
notches in the housing.
3. Inner Liner
2. Dome Cover 1. Dome Cover Screw
Drilling the Mounting Surface
1. Post the “Guide Pattern” sticker on the mounting surface.
NDF820/NDF820E l Quick Start Guide 5
English
2. Aiming the circles (the gure below marked with “+“ ) on the
sticker, drill four screw holes and one cable entry hole in the
ceiling/wall.
Lens Direction
Note: Mounting surface material
determines screw type.
Refer to manual.
GUIDE PATTERN
Mounting the Camera
1. Insert the plastic anchors into the screw holes (this gure take the
tapping type screws as the example to illustrate the mounting).
2. Tapping Type Screws
3. Inner Liner
4. Dome Cover
1. Plastic Anchors
Guide Pattern Sticker
5. Dome Cover Screw
6 NDF820/NDF820E l Quick Start Guide
2. Use the tapping screws to secure the camera base to the surface.
TipCautionWarning
Note
1. Use the machine type screws if you are attaching the camera to
a pendent mounting. Use the tapping type screws for all other
surfaces.
2. For cement surfaces, insert the “Plastic Anchors” into the holes. For
softer surfaces, do not use the “Plastic Anchors”.
3. Use the Rubber Feet for surface mounting.
Adjusting Camera Angle
Check the monitored view by wiring the RCA jack to a monitor. With an
external monitor connected, you can adjust pan and tilt angles of the
camera for appropriate or better view.
RCA Jack for
Composite Video Output
PanAdjustment:Rotate the lens base to adjust the horizontal angle.
TiltAdjustment:Tilt the lens base to adjust the vertical angle.
NDF820/NDF820E l Quick Start Guide 7
English
Tilt Angle = 90 degrees
Pan Angle = about 355 degrees
Horizontalrotation: Rotate the dome base to adjust the horizontal
position. Do not turn the base more than 355° as this may cause the
internal cables to twist and disconnect or break.
Horizontal Rotation = 355 degrees
8 NDF820/NDF820E l Quick Start Guide
TipCautionWarning
Note
When the tilt angle is less than 82 degrees, there is no distortion.
V=49.9° (Field of View)
82° Tilt Angle
Distortion
Area
Assembling the Camera
Follow the steps below when all the camera adjustments and cabling
tasks are nished.
1. Assemble the inner liner.
2. Assemble the dome cover.
3. Secure the dome cover with the accompanying screw.
2.2. Initial Conguration via a PC
Before connecting the camera to your network infrastructure, it’s
suggested that you connect the camera to a computer rst to perform
initial congurations.
1. Configure the computer’s IP address that must be on the
same network segment with the camera’s default IP address
(192.168.1.30 by default), such as:
• IPAddress:192.168.1.100
Ce manuel convient aux modèles suivants
1
Table des matières
Langues :
Autres manuels Messoa Caméra de sécurité
Messoa
Messoa NDF821PRO Manuel utilisateur
Messoa
Messoa NDR721 Manuel utilisateur
Messoa
Messoa A101RZ Manuel utilisateur
Messoa
Messoa NIC990 Manuel utilisateur
Messoa
Messoa NDF821 Manuel utilisateur
Messoa
Messoa NDZ760 Manuel utilisateur
Messoa
Messoa NCB750 Manuel utilisateur
Messoa
Messoa NCR870 Manuel utilisateur
Messoa
Messoa NDR890-HN5 Manuel utilisateur
Messoa
Messoa NDR891 Manuel utilisateur
Messoa
Messoa HCR176 Manuel utilisateur
Messoa
Messoa NCB750 Manuel utilisateur
Messoa
Messoa LPR615 Manuel utilisateur
Messoa
Messoa NDR891(H) Manuel utilisateur
Messoa
Messoa SCB267-HN5 Manuel utilisateur
Messoa
Messoa NDR891 Manuel utilisateur
Messoa
Messoa NCB855E Manuel utilisateur
Messoa
Messoa NCR875-HN5 Manuel utilisateur
Messoa
Messoa NIC830-HN5 Manuel utilisateur
Messoa
Messoa SCR368-HN5 Manuel utilisateur
