Mellanox Technologies QM8700 Manuel utilisateur

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels Mellanox Technologies Changer

Mellanox Technologies

Mellanox Technologies SwitchX Manuel utilisateur

Mellanox Technologies

Mellanox Technologies SX1710 Manuel utilisateur

Mellanox Technologies

Mellanox Technologies SX6015 Manuel utilisateur

Mellanox Technologies

Mellanox Technologies MSX6512-4R Manuel

Mellanox Technologies

Mellanox Technologies Mellanox SX1018 Manuel utilisateur

Mellanox Technologies

Mellanox Technologies MIS5024 Manuel utilisateur

Mellanox Technologies

Mellanox Technologies SX1710 Manuel utilisateur

Mellanox Technologies

Mellanox Technologies Mellanox SX1018 Mode d’emploi

Mellanox Technologies

Mellanox Technologies Spectrum SN2700 Instructions d'utilisation

Mellanox Technologies

Mellanox Technologies InfiniScale III Manuel utilisateur

Mellanox Technologies

Mellanox Technologies SwitchX-2 MSX6018F-1SFS Instructions d'utilisation

Mellanox Technologies

Mellanox Technologies IS5025 Manuel utilisateur

Mellanox Technologies

Mellanox Technologies MSX6512-NR Manuel

Mellanox Technologies

Mellanox Technologies MIS5022Q-1BFR Manuel utilisateur

Mellanox Technologies

Mellanox Technologies SX67X0 Instructions d'utilisation

Mellanox Technologies

Mellanox Technologies IS5025D-1BRC Manuel utilisateur

Mellanox Technologies

Mellanox Technologies MSX6536-10R Manuel

Mellanox Technologies

Mellanox Technologies MetroDX MTX6000-2SFS Manuel utilisateur

Mellanox Technologies

Mellanox Technologies SB7700 Manuel utilisateur

Mellanox Technologies

Mellanox Technologies MIS5035Q-2SFC Manuel utilisateur

Mellanox Technologies

Mellanox Technologies MIS5200Q-4DNC Manuel

Mellanox Technologies

Mellanox Technologies TX6100 MetroX Series Instructions d'utilisation

Mellanox Technologies

Mellanox Technologies 1G Switch Air Duct Rail Kit Manuel utilisateur

Mellanox Technologies

Mellanox Technologies Mellanox SX1018 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur

1U Switch Air Duct Kit

Quick Installation Guide

Model: QM8700/QM8790

Switch Air Duct Rail Kit

www.mellanox.com

2

Pay Attention!

•

All components must have the same airflow direction when installed in

the rack. A mismatch in the air flow direction will affect the heat dissi-

pation. Plan the FRU to connector or connector to FRU airflow, as

required.

Package Contents

•

1 x rail kit (including an air-duct unit)

•

Quick Start Guide

If anything is damaged or missing, contact your Mellanox representa-

tive at support@mellanox.com.

8X*

A

8X*

C

B 6X*

8X

D E

1X 2X

F

2X

1X

*Choose one nut type, according to the rack you are installing the system in

(square or round holes).

3

1

2 3

*REMOVE AND DISCARD 8 SCREWS, AND

DISASSAMBLE THE COVER IN THE OVAL. DISCARD THE

COVER.

D

D

D

*LOOSEN THE 2 CAPTIVE

FASTENERS, AND REMOVE

THE FRONT PANEL.

*INSTALL THE AIR DUCT UNIT ON THE

CHASSIS, AND INSERT THE

MUSHROOM INTO THE DESIGNATED

SLOTS.

4

4

5

*SLIDE THE SWITCH INWARDS, AND INSERT THE

MUSHROOM INTO THE DESIGNATED SLOTS.

*SLIDE THE RAILS ON THE SWITCH, UNTIL THE MUSHROOM

IS SITUATED PROPERLY IN THE DESIGNATED SLOTS.

3x

(per side)

D

D

F

F

C

TORQUE: 1.5±0.2Nm

5

6

7

A

A

2x

(per side)

B

*DO NOT TIGHTEN THE SCREWS YET.

E

E

6

8

9

*ROUTE THE REQUIRED CABLES

THROUGH THE DESIGNATED

WINDOW (RIGHT/LEFT/BOTH).

*PLUG THE CABLES.

F

E

(per side)

2x

TORQUE:

4.5±0.5Nm

B

*INSERT AND TIGHTEN 4 SCREWS AS

SHOWN BELOW, AND THEN TIGHTEN THE 4

SCREWS INSERTED IN THE PREVIOUS STEP.

7

10

Stacked Installation (Optional)

•

For stacked installation of adjacent switch assemblies in a rack, the

system on top should be installed without its floor, in order to allow

easier

access to FRUs. To remove the floor, unscrew

three screws on each side of

the system.

*SLIDE THE FRONT PANEL TOWARDS THE SWITCH,

AND TIGHTEN THE TWO CAPTIVE SCREWS.

8

•

The two systems in stacked mode are shown in the following figure:

•

Slide the front panels towards the switches, and tighten the captive

screws.

For full installation instructions, go to http://www.mellanox.com/-->Products->

InfiniBand/VPI Switch Systems

A C C 0 0 1 4 6 5 - 0 0