Mellanox Technologies MTS3610 Manuel utilisateur

Mellanox Technologies Inc. 350 Oakmead Parkway, Sunnyvale, CA 94085 Tel: 408-970-3400 Fax: 408-970-3403 www.mellanox.com

MTS3610 Installation Guide

Document Number

3082

Rev 1.2.2

Package Contents

The package includes:

•1Chassis

•1-18 leafs according to the amount ordered

• 18 - X leaf blanks X = the amount ordered

• 1 leaf fan module

• 1 spine fan module

•9spines

• 1- 2 management modules according to the amount ordered. If only 1 management module is ordered

then one MM blank will be in the package.

• 6-8 power cables depending upon your specific order

• 6-8 PSUs depending upon your specific order

• (8 - X) PSU blanks X = the amount ordered

• RJ45 to DB9 cable

• 1 Installation kit

•CD

• Installation guide

Before you install your new MTS3610 Chassis, unpack the system and check to make sure that all the parts

have been sent, check this against the parts list. Check the parts for visible damages that may have occurred

during shipping.

Note: If anything is damaged or missing, contact your customer representative immediately.

Physical Installation

Warning: This equipment is very heavy. Safety is the first concern. The fully

loaded chassis weighs ~350 lbs (155 kg). Make sure that proper manpower and

equipment are used for transporting and moving the chassis.

Note: You will need a mechanical lift, to move and insert the chassis into the rack.

This chassis can be installed in 19” racks with a maximum depth of 81cm.

The switch platform uses 20U of rack space in a standard 19” rack. The switch ships from the factory with

mounting racks on the front side. There are four threaded connectors on the top of the chassis for connecting

eye bolts. The four eye bolts are included in the installation kit. The chassis can be lifted using these four eye

bolts and a mechanical lift. The switch is supported from underneath the unit by a shelf.

Choose a rack which is able to support the mechanical and environmental characteristics of a fully populated

switch chassis as listed in the user manual.

MTS3610 Installation Guide

Mellanox Technologies

Rev 1.2.2 2

Note: A 20U mounting space is required for proper installation of the switch platform.

The rack mounting holes conform to the IEA-310 standard for 19-inch racks.

Guarantee proper ventilation, by leaving 8cm (3”) of space to the front and rear

of the switch. This will ensure proper air flow through the chassis. This is cru-

cial for maintaining good airflow at ambient temperature. In particular, route

cables such that they do not impede the air into or out of the chassis.

ESD Connection

Before starting any procedure on the MTS3610 Switch system:

Step 1. Put an ESD prevention wrist strap on your wrist, and make sure there is good contact between

your body and the strap.

Step 2. Plug the other end of the wrist strap to the MTS3610 chassis ESD connector on the

front of the switch system or connect it to a valid ground. Make sure that this is a tight

fit.

Figure 1: ESD Connector

Installing the Chassis

You will need:

• #2 phillips screwdriver

• a mechanical lift

• a grounding lug

• ground wire of sufficient length and gauge to properly ground the chassis

Parts included in the installation kit:

• 1 shelf • 5 Allen head screws

•1 lock down bar • 5 washers

• 4 eye bolts • 1 Allen wrench

• 2 rail slides • 26 sets of caged nuts and bolts

• 1 right hand cable holder • 1 left hand cable holder

ESD connector

MTS3610 Installation Guide

Mellanox Technologies

Rev 1.2.2 3

Figure 2: Installation Kit Parts

Before starting the procedure, put the ESD strap on and connect it to a valid ground.

Installing the Bottom Shelf

Step 1. Select the location in the rack. Try to keep the chassis as low as possible to keep the center of

gravity low.

Choose which way you want the chassis to face in the rack. Keep in mind that one side of the chassis can

have up to 324 cables connected. The other side of the chassis will have power cables. The distance between

the rack and the door will be small on one side of the rack as opposed to the other side of the rack.

Lock down bar

Rail slide

Eye bolts

Caged nuts and bolts

Right and Left

Cable holders

MTS3610 Installation Guide

Mellanox Technologies

Rev 1.2.2 4

Figure 3: Vertical Rails to Cabinet Measurement

Note: The side of the chassis with the power supply units will sit flush with the vertical supports of the rack.

The side of the chassis with the QSFP connectors will sit at the edge of the shelf closer to the center of the

rack.

Note: place the chassis as low as possible in the rack to keep the center of gravity as low as possible.

Step 2. Insert four caged nuts into the rack on the side you plan to have the connectors. Note

the U number on the rack.

Figure 4: Caged Nut Insertion

Step 3. Screw the rail slides onto the rack.

Figure 5: Rail Slide Installation

Step 4. Insert four caged nuts into the rack on the side you plan to have the powers supplies,

and spines. Use the same U number on this side of the rack as you used on the rail

side of the rack.

Step 5. Prepare the four bolts and keep them within reach.

Step 6. Slide the shelf onto the rail slides.

Step 7. Connect the shelf to the rack.

The caged nuts

are separated by a

single space.

MTS3610 Installation Guide

Mellanox Technologies

Rev 1.2.2 5

Figure 6: Shelf Installation

Step 8. Tighten all eight bolts into the caged nuts.

Inserting the Chassis

Step 1. Screw the four Eye bolts to the four corners of the top of the chassis.

Step 2. Connect the eye bolts to a Mechanical lifting device.

Figure 7: Mechanical Lifting Device

Step 3. Raise the chassis 2 cm (1”) above the level of the shelf.

Step 4. Move the chassis over the shelf. Place the chassis so that the face plate of the chassis

is a few inches from the vertical rack support.

Step 5. Lower the chassis onto the shelf.

Step 6. Remove the mechanical lifting device.

Step 7. Place ten caged nuts into the vertical rack support at the locations corresponding to

the holes in the chassis faceplate.

MTS3610 Installation Guide

Mellanox Technologies

Rev 1.2.2 6

Figure 8: Face Plate Mounting Bolt Locations

Step 8. Slide the chassis onto the shelf until the face plate of the chassis touches the vertical

rack support.

Step 9. Screw the bolts through the faceplate into the caged nuts, and tighten all ten bolts and

nuts.

Step 10. Place the lock down bar over the lip of the chassis, and align the holes in the lock

down bar with the holes in the shelf.

Figure 9: Lock Down Bar

Step 11. Place a washer on each Allen screw and screw down the lock down bar to the shelf

using the Allen wrench supplied. Use all 5 Allen screws.

Step 12. Connect a valid ground to the grounding post.

Holes in the

faceplate for

mounting on the

rack.

The lock down bar goes

over the lip on the bot-

tom of the chassis.

MTS3610 Installation Guide

Mellanox Technologies

Rev 1.2.2 7

Ground Connections

Make sure to connect the ground post to a valid electrical ground. Use a grounding lug and a ground wire of

sufficient capacity to safely convey a potential discharge. The chassis is concurrently grounded through each

of the PSUs. Only connect the PSU cords to properly grounded outlets. Do not rely on the PSU grounds. It is

absolutely necessary to connect the grounding post. Make sure the connections are solid and permanent.

Figure 10: Ground Connection

Installing the Cable Holder

Holes for

connecting

the cable

holder to the

rack

X 8

Left side

rack

Top side

X 8

Right side rack

Bottom side

Step 1. Place the Cable holder next to the rack and identify the holes for the caged nuts. The numbers

on the cable holders should face each other.

Step 2. Put the caged nuts into the previously identified holes in the rack.

Grounding

post

Grounding

post

Grounding lug

MTS3610 Installation Guide

Mellanox Technologies

Rev 1.2.2 8

Step 3. Screw the cable holder onto the rack using the screws provided.

Step 4. Repeat steps 1 to 3 for the second cable holder.

Powering Up the Switch Platform

Note: Make sure that the power cords are compatible with your outlets. Power cords for different countries

can be ordered from Mellanox.

Step 1. Plug in the power cords to the PSUs.

Step 2. Clamp each power cord to the chassis.

Each PSU has a clamp next to it, for supporting the power cord. Use this clamp to remove possible strain on

the PSU. The length of power cord between the clamp and the PSU must be less than 6” (15cm). See

Figure 11,“Electrical Cable Clamp”.

Step 3. Plug the other end of the power cord into a grounded outlet.

Note: It is recommended that the power to all of the power supplies be turned on at the same time.

Step 4. Repeat steps 1 to 3 for each of the remaining power supply units.

Note: A fully loaded MTS3610 switch system can draw 5.2 kW of power. Make sure that the outlets and

circuits will not be overloaded. Spread out the load over at least two or three circuits.

Figure 11: Electrical Cable Clamp

The switch system requires at least six PSUs to operate a fully populated platform. The seventh and eighth

PSUs provide a fail over protection mechanism such that the system will continue operating if one or more

of the PSUs fail. Connecting the PSUs to different AC lines provides AC fail over protection.

The system should continue to run and allow a hotswap of a defective PSU even if it has only six PSUs.

Step 5. As soon as a switch is plugged in, make sure that the green power LEDs on the PSUs

are on.

Step 6. Check the Status LEDs on all of the management modules and confirm that all of the

LEDs show status lights consistent with normal operation.

Warning: Any yellow status LEDs on any of the management modules is cause

for concern and must be dealt with immediately.

DC AC

OK FAIL OK

Clamp to remove strain on

the plug

MTS3610 Installation Guide

Mellanox Technologies

Rev 1.2.2 9

Step 7. Check that none of the ATTN status LEDs on the spines are yellow.

Step 8. Go around to the other side of the switch chassis and check the leaf board status

LEDs.

Step 9. Check that the leaf physical and data link status LEDs in the spines are lit.

Configuring the Switch for the First Time

Step 1. Connect the host PC to the RS-232 port of the MTS3610 switch using the supplied cable.

This LED should be off.

This LED should be on.

The green connector

LEDs should be on.

The yellow connector

LEDs should be

blinking.

Green – indicates Power OK

ATTN – Yellow indicates fault

in spine, normally off

Green – indicates that

there is a physical connec-

tion to the spines through

this link

Yellow – indicates that there

is a logical connection to the

spines through this link

Links A and B to each leaf

Leaf numbers

RS-232 port

MTS3610 Installation Guide

Mellanox Technologies

Rev 1.2.2 10

Note: No remote IP connection is available at this stage.

Step 2. Configure a serial terminal program (for example, HyperTerminal, minicom, or Tera

Term) on your host PC with the settings described in Table 1.

Step 3. Login (from serial terminal program) as admin and use admin as password. This starts

the Mellanox configuration wizard.

Step 4. Go through the Mellanox configuration wizard. Table 2 shows an example of a wiz-

ard session.

Make sure to connect to the RS-232 RJ-45 port of the switch and not to the ETH

port.

Table 1 - Serial Terminal Program Configuration

Parameter Setting

Baud Rate 9600

Data bits 8

Stop bits 1

Parity None

Flow Control None

Table 2 - Configuration Wizard Session (Sheet 1 of 2)

Wizard Session Display (Example) Comments

Do you want to use the wizard for

initial configuration?

You must perform this configuration the

first time you operate the switch or after

resetting the switch to the factory defaults.

Type ‘y’ and then press <Enter>.

Step 1: Hostname? [switch-1] If you wish to accept the default hostname,

then press <Enter>. Otherwise, type a dif-

ferent hostname and press <Enter>.

Step 2: Use DHCP on eth0 interface? Perform this step to obtain an IP address for

the switch. (eth0 is the management port of

the switch.)

If you wish the DHCP server to assign the

IP address, type ‘yes’ and press <Enter>.

If you type ‘no’, then you will be asked

whether you wish to use the ‘zeroconf’

configuration or not. If not, then you need

to enter a static IP.

Step 3: Admin password (Enter to

leave unchanged)? <new_password>

Step 3: Confirm admin password?

<new_password>

To avoid illegal access to the machine,

please type a password and then press

<Enter>. Then confirm the password by re-

entering it.

Note that password characters are not

printed.

Table des matières

Autres manuels Mellanox Technologies Changer

Mellanox Technologies

Mellanox Technologies SX67X0 Instructions d'utilisation

Mellanox Technologies

Mellanox Technologies SB7700 Manuel utilisateur

Mellanox Technologies

Mellanox Technologies MIS5022Q-1BFR Manuel utilisateur

Mellanox Technologies

Mellanox Technologies SX1710 Manuel utilisateur

Mellanox Technologies

Mellanox Technologies Spectrum SN2700 Instructions d'utilisation

Mellanox Technologies

Mellanox Technologies 1G Switch Air Duct Rail Kit Manuel utilisateur

Mellanox Technologies

Mellanox Technologies SB7700 Manuel utilisateur

Mellanox Technologies

Mellanox Technologies Spectrum SN2740 Instructions d'utilisation

Mellanox Technologies

Mellanox Technologies SX6015 Manuel utilisateur

Mellanox Technologies

Mellanox Technologies MIS5300 Manuel

Mellanox Technologies

Mellanox Technologies Spectrum SN2100 Manuel utilisateur

Mellanox Technologies

Mellanox Technologies MIS5600Q-10DNC Manuel utilisateur

Mellanox Technologies

Mellanox Technologies MIS5025 Manuel utilisateur

Mellanox Technologies

Mellanox Technologies MSX6512-4R Manuel

Mellanox Technologies

Mellanox Technologies MetroDX MTX6000-2SFS Manuel utilisateur

Mellanox Technologies

Mellanox Technologies SwitchX-2 MSX6005F-1BFS Instructions d'utilisation

Mellanox Technologies

Mellanox Technologies SX1710 Manuel utilisateur

Mellanox Technologies

Mellanox Technologies Grid Director 4036E Manuel utilisateur

Mellanox Technologies

Mellanox Technologies Mellanox SX1018 Manuel d'utilisation

Mellanox Technologies

Mellanox Technologies MSX6512-NR Manuel

Mellanox Technologies

Mellanox Technologies SX6720 Instructions d'utilisation

Mellanox Technologies

Mellanox Technologies switchx MSX1035B-1BRR Manuel utilisateur

Mellanox Technologies

Mellanox Technologies InfiniScale MTS3600Q-1UNC Manuel utilisateur

Mellanox Technologies

Mellanox Technologies SX6710 Instructions d'utilisation

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur