Meinberg IMS-VSG181H Manuel utilisateur

SETUP GUIDE

IMS-VSG181H

Hot-Plug Module

March 2, 2022

Meinberg Funkuhren GmbH & Co. KG

Table of Contents

1 Imprint 1

2 Change Log 2

3 Introduction 3

4 Important Safety Information 4

4.1 AdditionalSafetyInformation........................................ 4

4.2 PreventionofESDDamage......................................... 5

4.3 PowerSupply................................................. 6

4.4 Cabling..................................................... 6

5 IMS-VSG181H Module Connectors and Indicators 7

5.1 StatusLEDs.................................................. 8

5.2 BlackOutOutput............................................... 10

5.3 DARSOutput(Unbalanced)......................................... 10

5.4 D-Sub15-PinMulti-Output ........................................ 11

5.4.1 LTCOutput.............................................. 12

5.4.2 DARSOutput(Balanced)...................................... 12

5.4.3 WordClockOutput ......................................... 12

6 Before You Start 13

6.1 ContentsofDelivery............................................. 13

6.2 DisposalofPackagingMaterials...................................... 13

7 System Installation 14

7.1 Important Information Regarding Hot-Pluggable IMS Modules . . . . . . . . . . . . . . . . . . . . 14

7.2 Installation of Hot-Pluggable IMS Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

7.3 DataandSignalCables........................................... 16

8 Conﬁguration and Setup via Web Interface 17

8.1 Output1:BlackOut............................................. 18

8.2 Output2&4:DARS............................................. 20

8.3 Output3&6:LTC.............................................. 21

8.4 Output5:WordClock ............................................ 22

8.5 Misc ...................................................... 23

9 Troubleshooting 24

10 Your Opinion Matters to Us 25

11 RoHS and WEEE 26

12 List of Abbreviations 27

Date: March 2, 2022 IMS-VSG181H

1 Imprint

Meinberg Funkuhren GmbH & Co. KG

Lange Wand 9, 31812 Bad Pyrmont, Germany

Phone: + 49 (0) 52 81 / 93 09 - 0

Fax: + 49 (0) 52 81 / 93 09 - 230

Website: https://www.meinbergglobal.com

Email: [email protected]

Date: February 23, 2022

Manual

Version: 1.1

IMS-VSG181H Date: March 2, 2022 1

2 Change Log

Version Date Revision Notes

———————————————————————————————————————————————

1.0 10/29/2021 Initial version

———————————————————————————————————————————————

1.01 12/16/2021 Addition of change log & troubleshooting chapter, minor corrections

———————————————————————————————————————————————

1.1 2/23/2022 Corrections to frame rate support via LTC output, adjustments to Web

Interface following ﬁrmware updates, new screenshots, clariﬁcation

of information regarding LEDs, on-board oscillator and time zone

setting

2 Date: March 2, 2022 IMS-VSG181H

3 Introduction

This Setup Guide is a systematically structured guideline to assist you with the set-up of your Meinberg product.

The IMS-VSG181H is used to provide a reference video or audio signal for studio equipment, with gener-

ated signals output through two BNC outputs and a 15-pin D-Sub output. The "Black Out" BNC output is

used to deliver bi-level ("black & burst") and tri-level sync signals, while the "DARS Out" BNC output provides

an unbalanced Digital Audio Receiver Signal (DARS). The D-Sub connector serves as a multi-output solution

for several signal types, speciﬁcally balanced and unbalanced LTC signals, balanced DARS signals, and word

clock signals.

To ensure that the output signals remain highly precise even when switching between clocks using the RSC

module (in IMS systems with receiver redundancy), the IMS-VSG181H may be ﬁtted with a dedicated oscillator.

Functionality

The IMS-VSG181H is synchronized against an external reference frequency (10 MHz), a pulse-per-second sig-

nal (PPS), and a time string from an upstream clock. These synchronization signals are essential to maintaining

the precision of the output signals. The Web Interface provides a wide range of adjustment and customization

options for all output signal types. The signal outputs are phase-matched with the PPS signal.

Please refer to the LANTIME Firmware Manual for a more detailed description of all of the status moni-

toring conﬁguration options and features available for your Meinberg product.

LTOS7 Firmware Manual Download:

http://www.mbg.link/docg-fw-ltos

Compatibility

The IMS-VSG181H is an IMS module that is compatible with the following systems in the IMS product family

and can be used in the following slots:

PWR

CLK

CPU

MRI

ESI

I/O

M500

M1000

M1000 S

M2000 S

M3000

M3000 S

M4000

System Compatibility - IMS VSG181H

IMS System

Compatible

IMS Slot

Slot Compatibility - IMS VSG181H

To eliminate any risk of compatibility problems, your IMS system should have at least LANTIME OS Version

7.04 installed.

IMS-VSG181H Date: March 2, 2022 3

4 Important Safety Information

Please ensure that IMS modules designed for "hot-plugging" (modules that are removable and insertable while

a system is in operation) are always handled with the utmost care.

Before performing any maintenance work on the system:

•We recommend making a backup of any stored conﬁgurations (e.g. using a USB ﬂash drive or from the

Web UI)

•Take note of the chapter "Prevention of ESD Damage".

•Take note of the chapter "Power Supply".

4.1 Additional Safety Information

This manual contains important safety information regarding the installation and use of the device. Please read

it through fully before setting up the device for use.

This device may only be used for the purpose described in this manual. In particular, the speciﬁed operat-

ing limits of the device must be heeded. The person setting up the device is responsible for safety matters in

relation to any larger system in which the device is installed!

Failure to observe these instructions may have an adverse impact on device safety!

Please keep this manual in a safe and accessible place.

Target Readership

This manual is only intended to be used by qualiﬁed electricians, or by persons who have been appropriately

instructed by qualiﬁed electricians and who are familiar with applicable national standards and safety rules &

regulations, especially in relation to the installation of low-voltage (< 1000 V) installations.

4 Date: March 2, 2022 IMS-VSG181H

4 Important Safety Information

4.2 Prevention of ESD Damage

ATTENTION!

An ESDS device (electrostatic discharge-sensitive device) is any device at risk of damage or

malfunction due to electrostatic discharges (ESD) and thus requires special measures to prevent

such damage or malfunction. Systems and modules with ESDS devices usually bear the following

symbol:

Symbol Indicating Devices with ESDS Components

The following measures will help to protect ESDS components from damage and malfunction.

When preparing to dismantle or install devices:

Ground your body (for example, by touching a grounded object) before touching sensitive devices.

Ensure that you wear a grounding strap on your wrist when handling such devices. These straps must

in turn be attached to an uncoated, non-conductive metal part of the system.

Use only tools and devices that are free of static electricity.

When transporting devices:

Devices must only be touched or held by the edges. Never touch any pins or conductors on the device.

When dismantling or installing devices:

Avoid coming into contact with persons who are not grounded. Such contact may compromise your

connection with the earth conductor and thus also compromise the device’s protection from any

static charges you may be carrying.

When storing devices:

Always store devices in ESD-proof ("antistatic") bags. These bags must not be damaged in any way.

ESD-proof bags that are crumpled or have holes cannot provide eﬀective protection against

electrostatic discharges.

ESD-proof bags must have a suﬃcient electrical resistance and must not be made of conductive

metals if the device has a lithium battery ﬁtted on it.

IMS-VSG181H Date: March 2, 2022 5

4.3 Power Supply

WARNING!

The IMS system in which the module is used is operated at a dangerous voltage. Please refer to your IMS

Manual for more information about safety.

When removing a hot-pluggable power supply unit, always disconnect its power cable before removing it from

the IMS system.

Never open a power supply unit—there may still be hazardous residual voltages present even after disconnec-

tion from the mains supply. In the event that a power supply unit is no longer working (e.g. defective), please

return it to Meinberg for repair.

Failure to observe these safety instructions may result in serious injury and/or property damage. The IMS

system must only be installed, set up, and operated by qualiﬁed personnel.

4.4 Cabling

WARNING!

Danger of death from electric shock! Never work on the system while the power is live! Always disconnect the

cables from the devices at both ends before working on the plugs and terminals of connected cables!

6 Date: March 2, 2022 IMS-VSG181H

5 IMS-VSG181H Module Connectors and Indicators

5 IMS-VSG181H Module Connectors and

Indicators

The numbering in the drawing above relates to the relevant subsection in this chapter.

IMS-VSG181H Date: March 2, 2022 7

Table des matières

Autres manuels Meinberg Matériel informatique

Meinberg

Meinberg GPS170PEX Manuel utilisateur

Meinberg

Meinberg TCR180PEX-EL Manuel utilisateur

Meinberg

Meinberg DI/BGT TTL Manuel utilisateur

Meinberg

Meinberg TCR180 Manuel utilisateur

Meinberg

Meinberg GPS170PCI Manuel utilisateur

Meinberg

Meinberg Line InterfaceUnit v2.0 Manuel utilisateur

Meinberg

Meinberg LANTIME Manuel utilisateur

Meinberg

Meinberg CPU-C15G2 Manuel utilisateur

Meinberg

Meinberg DI32 Manuel utilisateur

Meinberg

Meinberg IMS-GPS182 Manuel utilisateur

Meinberg

Meinberg GNS181PEX Manuel utilisateur

Meinberg

Meinberg BPE-2000 Manuel utilisateur

Meinberg

Meinberg GPS167PC Manuel utilisateur

Meinberg

Meinberg GPS180PEX Manuel utilisateur

Meinberg

Meinberg TCR510PCI Manuel utilisateur

Meinberg

Meinberg IMS-LNO Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur