Mediatrix 1104 Guide de démarrage rapide
C
CC
C
C
CC
Co
oo
o
o
oo
on
nn
n
n
nn
nf
ff
f
f
ff
fi
ii
i
i
ii
ig
gg
g
g
gg
gu
uu
u
u
uu
ur
rr
r
r
rr
ra
aa
a
a
aa
at
tt
t
t
tt
ti
ii
i
i
ii
io
oo
o
o
oo
on
nn
n
n
nn
n
N
NN
N
N
NN
No
oo
o
o
oo
ot
tt
t
t
tt
te
ee
e
e
ee
es
ss
s
s
ss
s
2
22
2
2
22
23
33
3
3
33
30
00
0
0
00
0
PBX Remote Line Extension using Mediatrix 1104 and
1204
February 21, 2006
Proprietary
2006 Mediatrix Telecom, Inc.
Configuration Notes
0230
Page 2 of 23
Table of Contents
Introduction ........................................................................................................................................................................... 3
Application Scenario............................................................................................................................................................. 3
Running the Unit Manager Network Software....................................................................................................................... 4
Configuring the Mediatrix 1104............................................................................................................................................. 7
Configuring the Mediatrix 1204........................................................................................................................................... 12
Appendix A – Troubleshooting Tips.................................................................................................................................... 23
Configuration Notes
0230
Page 3 of 23
Introduction
These Configuration Notes are distributed to partners and technical support personnel as an aid to configure units in a PBX
Remote Line Extension scenario. They are specific to the SIP v5.0 firmware.
Application Scenario
With VoIP, the distance limitation of extending copper wire from a PBX to a remote location is no longer an issue.
Small remote branch offices (SOHOs) can now have existing analog phones installed at the remote site as analog
extensions of the PBX system at the Main Office.
Requirement for fax at remote branch office.
Requirement for analog phone at remote branch office.
Toll-Bypass for intra-office calls.
The following configuration notes are not a substitute for the Mediatrix Administration Documentation for Mediatrix analog
products. Please have the following manuals available for reference:
Mediatrix 1104 SIP Reference Manual (SIP v5.0 version).
Mediatrix 1204 SIP Reference Manual (SIP v5.0 version).
Mediatrix Unit Manager Network Administration Manual and Quick Start guide (UMN v3.2).
Configuration Notes
0230
Page 4 of 23
Running the Unit Manager Network Software
The Unit Manager Network (UMN) software is a configuration and management tool for Mediatrix devices. The UMN is
provided on the CD included with the unit. It has a default 3-units limit upon installation. This will suffice for most
configurations.
It is recommended that the administrator uses the UMN to configure the Mediatrix devices. Please refer to the UMN Quick
Start guide for the installation of the software. Once the UMN software has been installed on your PC
1
, proceed with the
following steps.
Step 1: Start the UMN
Select from the Start Menu > Programs > Unit Manager Network 3.2 > Unit Manager Network.
Step 2: Login to the UMN
In the Administrator login window (Connect to Unit Manager), a User Name and Password are not required. Click
OK to proceed.
Step 3: Perform an Autodetect
On the left pane, right-click the Unit Manager level, then select Autodetect.
Set the IP Address Range to minimize the time it takes to auto-detect the unit. Click Start to begin Mediatrix unit
detection. When the unit is detected, the Result section lists the unit.
Select the unit and click OK. If no DHCP server is used in your subnet, you must connect one unit at a time since
they will start by using the default IP address 192.168.0.1 after a recovery reset. You will have to set a different
static IP address for every unit. Please see the 1100 series and 1204 SIP Quick Start Guide for more details on
initial setup.
1
If you are having trouble opening the UMN application, verify that the status of the “Unit Manager Network 3.2” service is started. See Page
5 to access Windows Services.
Configuration Notes
0230
Page 5 of 23
Note: The UMN runs in the Windows background. Mediatrix highly recommends that the administrator stops and restarts the
UMN service whenever the IP address of the PC is changed. A restart may be needed depending on your Windows O/S.
Go to Start Menu > Settings > Control Panel > Administrative Tools > Services.
Stop and restart the Unit Manager Network 3.2 service.
Configuration Notes
0230
Page 6 of 23
Alternatively, you can configure multiple IP addresses on the same PC network interface card (only in static IP
mode – not DHCP) to avoid restarting the computer or stopping and restarting the UMN service whenever you
change the IP address and subnet of the Mediatrix unit. This is recommended for advanced IP network users, the
current configuration notes do not cover the step by step setting for this alternative.
Configuration Notes
0230
Page 7 of 23
Configuring the Mediatrix 1104
Step 1: Setting Basic Network Parameters
Once the Mediatrix 1104 has been auto-detected, it should appear under the Unit Manager level. Right-click the
Administration level of the Mediatrix 1104 and select the Edit menu.
Configure the IP addresses to reflect your network. Uncheck Use DHCP if you are using static IP addresses.
Restart the unit after the configuration of IP addresses for the unit to accept the new addresses.
When using DHCP: you can also reserve the IP address for the Mediatrix 1104 by assigning the MAC address of
the unit to a specific IP address in your DHCP server – it will be easier to auto-detect the unit for provisioning. An
example of a unit IP address fetched by DHCP is shown in the figure below.
Another alternative to determine the IP address of the unit fetched by DHCP is to connect a telephone into port #2
of the Mediatrix 1104 and dial *#*0”. An internal IVR will provide the IP address of the unit.
Configuration Notes
0230
Page 8 of 23
Step 2: Set the SIP Server Redirection
Select the Sip page and set the following:
oUncheck Use DHCP.
oSet the SIP Registrar field to empty since registration will not be required.
oSet the SIP Proxy field to be the IP address of the destination2 device. In this scenario, the destination IP
address is that of the Mediatrix 1204.
oClick in the User Name field next to the port number and type the telephone, fax, or extension number of
the Mediatrix 1104 port. Each port on the 1104 requires a User Name.
2
Using this setup will route all calls from the Mediatrix 1104 to the assigned IP address, that is our Mediatrix 1204. Note that you cannot use
this configuration to route calls to more than one unit.
Configuration Notes
0230
Page 9 of 23
Step 3: Access the Edit SNMP Window
Right-click the unit and select Edit SNMP.
Step 4: Set the Port Behaviour
On the top menu bar, check the option Automatic GET.
Go to iso>org>dod>internet>private>enterprises>mediatrix > mediatrixExperimental > sipExperimentalMIB >
sipExperimentalMIBObjects > sipUnregisteredPortBehavior and set this parameter to enableport in the drop
down menu that appears upon double-clicking the value located in the upper-right pane.
Configuration Notes
0230
Page 10 of 23
Step 5: NAT Traversal Configuration
You must configure the following parameters for the Mediatrix unit to work behind a NAT/Firewall router:
oGo to mediatrix > mediatrixExperimental > sipExperimentalMIB > sipExperimentalMIBObjects >
sipNatCustom > sipNatCustomEnable and set this parameter to enable.
oGo to mediatrix > mediatrixExperimental > sipExperimentalMIB > sipExperimentalMIBObjects >
sipNatCustom > sipNatCustomPublicAddress and set the parameter to be the public IP address of the
NAT/Firewall router where the Mediatrix 1104 is located. In this scenario, the IP address would be
69.129.134.6 as shown in the following figure.
Autres manuels pour 1104
3
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Mediatrix Porte
Mediatrix
Mediatrix 3632 Manuel utilisateur
Mediatrix
Mediatrix 4400 Series Instructions d'installation et d'utilisation
Mediatrix
Mediatrix 1104 Manuel utilisateur
Mediatrix
Mediatrix 1204 Mode d’emploi
Mediatrix
Mediatrix 1104 Manuel utilisateur
Mediatrix
Mediatrix 1104 Manuel utilisateur
Mediatrix
Mediatrix 3621 Manuel
Mediatrix
Mediatrix 3500 Series Manuel utilisateur
Mediatrix
Mediatrix 2102 Manuel utilisateur
Mediatrix
Mediatrix 1102 Manuel utilisateur
Manuels Porte populaires d'autres marques
LST
LST M500RFE-AS Manuel utilisateur
Kinnex
Kinnex Media Gateway Manuel utilisateur
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuel utilisateur
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur
Telsey
Telsey CPVA 500 - SIP Manuel utilisateur
