MCCI Catena 4801 Guide de référence
MCCI Corporation
3520 Krums Corners Road
Ithaca, New York 14850 USA
Phone +1-607-277-1029
Fax +1-607-277-6844
www.mcci.com
Catena 4801 Assembly Instructions and Test Procedure
Engineering Report 234001157
Rev A
Date: 2018-12-11
Copyright © 2018
All Rights Reserved
Catena 4801 Assembly Instructions and Test Procedure
Engineering Report 234001157 Rev A
- ii -
PROPRIETARY NOTICE AND DISCLAIMER
Unless noted otherwise, this document and the information herein disclosed are proprietary to MCCI
Corporation, 3520 Krums Corners Road, Ithaca, New York 14850 (“MCCI”). Any person or entity to
whom this document is furnished or having possession thereof, by acceptance, assumes custody thereof
and agrees that the document is given in confidence and will not be copied or reproduced in whole or in
part, nor used or revealed to any person in any manner except to meet the purposes for which it was
delivered. Additional rights and obligations regarding this document and its contents may be defined by
a separate written agreement with MCCI, and if so, such separate written agreement shall be controlling.
The information in this document is subject to change without notice, and should not be construed as a
commitment by MCCI. Although MCCI will make every effort to inform users of substantive errors, MCCI
disclaims all liability for any loss or damage resulting from the use of this manual or any software
described herein, including without limitation contingent, special, or incidental liability.
MCCI, TrueCard, TrueTask, MCCI Catena, and MCCI USB DataPump are registered trademarks of MCCI
Corporation.
MCCI Instant RS-232, MCCI Wombat and InstallRight Pro are trademarks of MCCI Corporation.
All other trademarks and registered trademarks are owned by the respective holders of the trademarks
or registered trademarks.
Copyright © 2018 by MCCI Corporation.
Document Release History
Draft 1
2018-12-11
First draft
Draft 2
2018-12-13
Second draft
Rev A
2018-12-26
Initial Release
Catena 4801 Assembly Instructions and Test Procedure
Engineering Report 234001157 Rev A
- iii -
TABLE OF CONTENTS
1 Introduction .......................................................................................................................................... 7
2 Catena 4801 Assembly Requirements .................................................................................................. 7
2.1 Catena 4801 .................................................................................................................................. 7
2.2 1x03 Screw Terminals ................................................................................................................... 8
2.3 1x02 Screw Terminals ................................................................................................................... 8
2.4 1X05 Pin Header............................................................................................................................ 8
2.5 1X03 Pin Header............................................................................................................................ 8
2.6 Power Source ................................................................................................................................ 9
3 Catena 4801 Assembly Instructions...................................................................................................... 9
3.1 Install The Screw Terminals .......................................................................................................... 9
3.2 Install the Pin Headers ................................................................................................................10
3.3 Catena 4801 setup with Test Clip ...............................................................................................11
4 Board Description ............................................................................................................................... 12
5 Software Requirements ......................................................................................................................12
6 Test Setup ........................................................................................................................................... 13
6.1 Catena 4801 Test Setup Requirement ........................................................................................ 13
6.1.1 ST-LINK/V2 in-circuit debugger/programmer..................................................................... 13
6.1.2 RS485 Module..................................................................................................................... 13
6.1.3 USB to Serial Cable.............................................................................................................. 14
6.2 Catena 4801 Configuration .........................................................................................................14
7 Test Procedure.................................................................................................................................... 17
7.1 Library Packages.......................................................................................................................... 17
7.2 Programming Catena4801 Using STLink ..................................................................................... 17
7.2.1 ST Link Configuration .......................................................................................................... 17
7.3 Configuring RS-485 module ........................................................................................................ 20
7.4 Connecting to the network .........................................................................................................22
7.4.1 Registering the device......................................................................................................... 23
7.4.2 Configuration steps............................................................................................................. 24
7.5 Test Results .................................................................................................................................25
Catena 4801 Assembly Instructions and Test Procedure
Engineering Report 234001157 Rev A
- iv -
LIST OF TABLES
Table 1 Catena4801 to RS485 Connection.................................................................................................. 15
Table 2 USB to Serial Connection................................................................................................................ 16
Table 3 Catena4801 to STLink connection.................................................................................................. 17
LIST OF FIGURES
Figure 1 Catena 4801 .................................................................................................................................... 7
Figure 2 1X03 Screw Terminal....................................................................................................................... 8
Figure 3 1X02 Screw Terminal....................................................................................................................... 8
Figure 4 1X05 Pin Header.............................................................................................................................. 8
Figure 5 1X03 Pin Header.............................................................................................................................. 9
Figure 6 Battery............................................................................................................................................. 9
Figure 7 Catena 4801 with 1x02 Screw Terminal........................................................................................10
Figure 8 Catena 4801 with 1x03 Screw Terminal........................................................................................10
Figure 9 Catena 4801 with 1x05 and 1x03 Pin Header ............................................................................... 11
Figure 10 Catena 4801 with test clip assembly........................................................................................... 11
Figure 11 Catena 4801 Description............................................................................................................. 12
Figure 12 ST Link Programmer.................................................................................................................... 13
Figure 13 USB to RS-485 Converter ............................................................................................................ 13
Figure 14 USB to Serial Cable...................................................................................................................... 14
Figure 15 Catena 4801 Battery Configuration ............................................................................................14
Figure 16 Catena 4801 with Battery ........................................................................................................... 15
Figure 17 Catena 4801 with RS485 ............................................................................................................. 15
Figure 18 Catena 4801 Serial Configuration ...............................................................................................16
Figure 19 Catena 4801 Overall Test Setup.................................................................................................. 16
Figure 20 STLink .......................................................................................................................................... 18
Figure 21 Upload setup using STLink debugger.......................................................................................... 18
Figure 22 Selection of board .......................................................................................................................19
Figure 23 Selecting the Serial Interface ...................................................................................................... 20
Figure 24 Execution of pyModSlave application.........................................................................................20
Figure 25 Setting up Modbus RTU mode.................................................................................................... 21
Figure 26 Modbus RTU settings dialog box ................................................................................................ 21
Figure 27 Setting up Modbus mode and configuring slave ........................................................................22
Figure 28 Selection of Bus Monitor and Starting the communication .......................................................22
Figure 29 Creating Application.................................................................................................................... 23
Figure 30 Added Application....................................................................................................................... 23
Figure 31 Registering the device.................................................................................................................24
Figure 32 Registering the device with parameters .....................................................................................24
Figure 33 Device shown up with connection status and Data tab to view data.........................................25
Figure 34 Serial output of Catena 4801 in Arduino IDE .............................................................................. 26
Catena 4801 Assembly Instructions and Test Procedure
Engineering Report 234001157 Rev A
- v -
Figure 35 Bus Monitor using pyModSlave ..................................................................................................26
Figure 36 Data in TTN Console....................................................................................................................27
LIST OF SEQUENCE DIAGRAMS
No table of figures entries found.
Catena 4801 Assembly Instructions and Test Procedure
Engineering Report 234001157 Rev A
- 7 -
1Introduction
This document outlines the Catena 4801 board description and also about the assembly
and test procedure instructions.
2Catena 4801 Assembly Requirements
2.1 Catena 4801
Catena 4801 (123001401) has Murata LoRa Module IC (CMWX1ZZABZ-078), FRAM
(MB85RC64TA), Flash IC (MX25V8035FZUI), RS485 Transceiver IC (SN65HVD75DR), Boost
Regulator (MCP16252), High Side Switch (TPS22960).
Figure 1 Catena 4801
Catena 4801 Assembly Instructions and Test Procedure
Engineering Report 234001157 Rev A
- 8 -
2.2 1x03 Screw Terminals
1X03 screw terminal (123001438) is to connect the board with RS485 module.
Figure 2 1X03 Screw Terminal
2.3 1x02 Screw Terminals
1X02 screw Terminal(123001439) is to connect the battery to the board to provide Power.
Figure 3 1X02 Screw Terminal
2.4 1X05 Pin Header
1X05 pin header (123001440) is used to program the board using ST Link
Figure 4 1X05 Pin Header
2.5 1X03 Pin Header
1X03 Pin header(123001441) is used for Serial communication
Catena 4801 Assembly Instructions and Test Procedure
Engineering Report 234001157 Rev A
- 9 -
Figure 5 1X03 Pin Header
2.6 Power Source
Any power source which provide 3.3V can be used to power Catena-4801.
Figure 6 Battery
3Catena 4801 Assembly Instructions
3.1 Install The Screw Terminals
1. Attach the 1X02 Screw Terminal on JP6
I. Solder one post
II. Adjust for proper alignments and good cosmetics
III. Solder the remaining posts
Catena 4801 Assembly Instructions and Test Procedure
Engineering Report 234001157 Rev A
- 10 -
Figure 7 Catena 4801 with 1x02 Screw Terminal
2. Attach the 1X03 Screw Terminal on JP3
I. Solder one post
II. Adjust for proper alignments and good cosmetics.
III. Solder the remaining posts
Figure 8 Catena 4801 with 1x03 Screw Terminal
3.2 Install the Pin Headers
1. Attach the 1X05 Pin Header and 1X03 Pin Header on JP1 and JP4 respectively.
I. Solder one or two posts on each strip, to tack the header in place
II. Adjust the vertical and horizontal alignment
III. Solder the remaining posts for reliable electrical contact.
Table des matières
Autres manuels MCCI Matériel réseau
Manuels Matériel réseau populaires d'autres marques
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuel utilisateur
Yudor
Yudor YDS-16 Manuel utilisateur
D-Link
D-Link ShareCenter DNS-320L Manuel utilisateur
Samsung
Samsung ES1642dc Instructions d'utilisation
Honeywell Home
Honeywell Home LTEM-PV Instructions de montage
