Maytag CWE5100ACB10 Manuel utilisateur

INSTALLATION INSTRUCTIONS

24" (61.0 CM) ELECTRIC SINGLE AND DOUBLE

BUILT-IN OVEN

Table of Contents

BUILT-IN OVEN SAFETY ............................................................... 1

INSTALLATION REQUIREMENTS ................................................ 2

Tools and Parts............................................................................ 2

Location Requirements ............................................................... 2

Electrical Requirements ............................................................... 3

INSTALLATION INSTRUCTIONS .................................................. 4

Prepare Built-In Oven .................................................................. 4

Oven Door .................................................................................... 4

Make Electrical Connection ......................................................... 5

Install Oven .................................................................................. 7

Complete Installation ................................................................... 8

BUILT-IN OVEN SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

iMPORTANT:

Save for local electrical inspector's use.

W10203506A

INSTALLATION REQUIREMENTS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

• Phillips screwdriver

• Measuring tape

• Hand or electric drill (for wall cabinet installations)

• 1" (25 mm) drill bit (for wall cabinet installations)

• Level

Parts needed

• UL listed or CSA approved conduit connector

• UL listed wire connectors

Parts supplied

• 0.188 x 2.1" screws - single oven (4), double oven (6)

Check local codes. Check existing electrical supply. See

"Electrical Requirements."

It is recommended that all electrical connections be made by a

licensed, qualified electrical installer.

._@] _, ;: ,,._,_

IMPORTANT: Observe all governing codes and ordinances.

• Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance with oven.

• Recessed installation area must provide complete enclosure

around the recessed portion of the oven.

• Grounded electrical supply is required. See "Electrical

Requirements" section.

• Electrical supply junction box should be located in the upper

right corner, 4" (10.2 cm) below the upper cut out surface of

the cabinet.

Oven support surface must be solid, level and flush with

bottom of cabinet cutout. Floor must be able to support a

single oven weight of 154 Ibs (70 kg) or a double oven weight

of 287 Ibs (130 kg).

Product Dimensions - Single Oven

A. 221/4''(56.5 cm) max. recessed width

B. 29%" (75.3 cm) max. overafl height

C. 23%" (60.6 cm) overall width

D. 22%" (57.5 cm) max. recessed depth

E. 277/8"(70.8 cm) recessed height

Cabinet Dimensions - Single Oven

Single Oven Installed in Cabinet

IIII B

A. 24" (61 cm) min. cabinet width

B. 11/_"(3.8 cm) top of cutout to bottom of upper cabinet

door

C. 331/4'' (84.5 cm) min. bottom of cutout to floor

D. 22%" (56.8 cm) cutout width

E. 11/_'' (3.8 cm) min. bottom of cutout to top of cabinet door

F. 2811A6'' (72.9 cm) cutout height

Product Dimensions - Double Oven

Cabinet Side View - Double or Single Oven

E_ D_C

A. 221/4''(56.5 cm) max. recessed width

B. 46%6" (117.6 cm) max. overafl height

C. 237/8''(60.6 cm) overafl width

D. 22%" (57.5 cm) max. recessed depth

E. 44%" (113.4 cm) recessed height

Cabinet Dimensions - Double Oven

Double Oven Installedin Cabinet

A. 24" (61 cm) min. cabinet width

B. 11/2''(3.8 cm) top of cutout to bottom of upper

cabinet door

C. 17" (43.2 cm) min. bottom of cutout to floor

D. 223/8'' (56.8 cm) cutout width

E. 11/2''(3.8 cm) min. bottom of cutout to top of

cabinet door

F. 453/8'' (115.3 cm) cutout height

A. 24"(61 cm) min. cutout depth

B. 22%" (57.5 cm) recessed oven depth

C. Oven front

D. Recessed oven

E.Cabinet

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrical installer determine that

the ground path and the wire gauge are in accordance with local

codes.

Check with a qualified electrical installer if you are not sure the

oven is properly grounded.

This oven must be connected to a grounded metal, permanent

wiring system.

Be sure that the electrical connection and wire size are adequate

and in conformance with the National Electrical Code, ANSI/

NFPA 70-latest edition or CSA Standards C22.1-94, Canadian

Electrical Code, Part 1 and C22.2 No. O-M91-1atest edition, and

all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

Electrical Connection

To properly install your oven, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here.

• Oven must be connected to the proper electrical voltage and

frequency as specified on the model/serial number rating

plate. The model/serial number rating plate is located at the

bottom right-hand oven surface. See the following illustration.

Single Oven

A. Model/serial number plate

Double Oven

A. Model/serial number plate

• Double oven model rated from 6.5 kw to 8.6 kw at 208 V to

240 V requires a separate 40 amp circuit.

• Single oven model rated at 4.4 kw to 5.8 kw at 208 V to 240 V

requires a separate 30 amp circuit.

A circuit breaker (or time-delay fuse) is recommended.

Connect directly to the circuit breaker box (or fused

disconnect) through flexible, armored or nonmetallic

sheathed, copper cable (with grounding wire). See "Make

Electrical Connection" section.

Flexible conduit from the oven should be connected directly

to the junction box.

Do not cut the conduit. The length of conduit provided is for

serviceability of the oven.

A UL listed or CSA approved conduit connector must be

provided.

If the house has aluminum wiring follow the procedure below:

1. Connect a section of solid copper wire to the ends of the

flexible conduit leads.

2. Connect the aluminum wiring to the added section of

copper wire using special connectors and/or tools

designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended

procedure. Aluminum/copper connection must conform with

local codes and industry accepted wiring practices.

INSTALLATION INSTRUCTIONS

1. Decide on the final location for the oven. Locate existing

wiring to avoid drilling into or severing wiring during

installation.

Excessive Weight Hazard

Use two or more people to move and install oven.

Failure to do so can result in back or other injury.

Remove Oven Door.

IMPORTANT: Use both hands to remove oven doors.

1. Open door to the broil stop position (about 4 to 6 inches).

2. Grasp sides of the door at the middle. Slowly lift door straight

up.

2. To avoid floor damage, set the oven onto cardboard prior to

installation. Do not use handle or any portion of the front

frame or trim for lifting.

3. Remove the shipping materials and tape from the oven.

4. Remove the hardware package from inside the bag

containing literature.

5. Remove and set aside racks and other parts from inside the

oven.

3. While lifting the door up, very slightly open the door by pulling

it forward. Check that the latches swing down into the

notches on the hinge arms.

6. Move oven and cardboard close to the oven's final location.

For Double Ovens

Electrical Shock Hazard

Disconnect power before servicing.

Use 8 gauge solid copper wire.

Electrically ground oven.

Failure to follow these instructions can result in death,

fire, or electrical shock.

For Single Ovens

Electrical Shock Hazard

Disconnect power before servicing.

Use 12 gauge solid copper wire.

Electrically ground oven.

Failure to follow these instructions can result in death,

fire, or electrical shock.

This oven is manufactured with a neutral (white) power supply

wire and a cabinet-connected green (or bare) ground wire twisted

together.

1. Disconnect power.

2. Feed the flexible conduit from the oven through the opening

in the cabinet.

Electrical Connection Options Chart

If your home has: Go to section:

4-wire 4-wire Cable from Home

Power Supply

4. Remove junction box cover, if it is present.

Install a UL listed or CSA approved conduit connector to the

junction box.

A. UL listed or CSA approved conduit connector

3-wire 3-wire Cable from Home

Power Supply

5. Route the flexible conduit from the oven to the junction box

through a UL listed or CSA approved conduit connector.

6. Tighten screws on conduit connector.

7. See "Electrical Connection Options Chart" to complete

installation for your type of electrical connection.

4-Wire Cable from Home Power Supply

IMPORTANT: Use the 4-wire cable from home power supply in

the U.S. where local codes do not allow grounding through

neutral, New Branch circuit installations (1996 NEC), mobile

homes and recreational vehicles, new construction and in

Canada.

C H

D............................................................................................................................I

A. Cable from home power supply

B. Black wires

C. Red wires

D. 4-wire flexible conduit from

oven

E.Junction box

F. White wires

G. UL fisted wire connectors

H. Green (or bare) ground wires

I. UL listed or CSA approved

conduit connector

1. Connect the 2 black wires (B) together using a UL listed wire

connector.

2. Connect the 2 red wires (C) together using a UL listed wire

connector.

3. Untwist white wire from green (or bare) ground wire coming

from the oven.

4. Connect the 2 white wires (F) together using a UL listed wire

connector.

5. Connect the green (or bare) ground wire (H) from the oven

cable to the green (or bare) ground wire (in the junction box)

using a UL listed wire connector.

6. Install junction box cover.

3-Wire Cable from Home Power Supply -U.S. Only

IMPORTANT: Use the 3-wire cable from home power supply

where local codes permit a 3-wire connection.

A. Cable from home power supply F. 4-wire flexible conduit from

B. Junction box oven

C. Black wires G. Red wires

D. White wires H. UL listed wire connectors

E. Green (or bare) ground wire I. UL listed or CSA approved

(from oven) conduit connector

1. Connect the 2 black wires (C) together using a UL listed wire

connector.

2. Connect the 2 white wires (D) and the green (or bare) ground

wire (of the oven cable) using a UL listed wire connector.

3. Connect the 2 red wires (G) together using a UL listed wire

connector.

4. Install junction box cover.

Excessive Weight Hazard

Use two or more people to move and install oven.

Failure to do so can result in back or other injury.

Using 2 or more people, lift oven partially into cabinet cutout.

Use the oven opening as an area to grip.

NOTE: Push against seal area of oven front frame when

pushing oven into cabinet. Do not push against outside

edges.

\..

3= Securely fasten oven to cabinet using the 0.188 x 2.1" screws

(4 for single oven, 6 for double oven) provided. Insert the

screws through holes in decorative trim. To avoid cabinet

damage, use the 0.140" diameter (number 28) drill bit to pre-

drill the pilot holes before driving screws. Do not overtighten

screws.

A. Decorative trim

B. Insert screw.

4. Replace oven racks.

5. Grasp sides of the door and align slots in door with the hinge

arms.

Push oven completely into cabinet and center oven into

cabinet cutout. 6. Slightly pull the door open as you slide the door down onto

the hinge arms. The sliding action of the door will disengage

the latches on the hinge arms.

7. Gently push the door downward until the door rests evenly on

the hinges.

8. Close door.

9. Repeat for lower oven door.

10. Reconnect power.

11. Display panel will light briefly, and "PF" should appear in the

display.

12. If display panel does not light, please reference the

"Assistance or Service" section of the Use and Care Guide or

contact the dealer from whom you purchased your oven.

C_m_t _ ...... "_ •_ _

1. Check that all parts are now installed. If there is an extra part,

go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. For oven use and cleaning, read the Use and Care Guide.

Check Operation of Oven(s)

1. Turn power on. The time should flash in the display.

2. Check that the oven door(s) is closed

3. Turn on the oven(s) Broil function. See the User Instructions

for more information.

If oven(s) does not operate, check the following:

• Electrical supply is connected.

• See "Troubleshooting" section in the Use and Care Guide.

When oven has been on for 5 minutes, feel for heat.

If you do not feel heat or if an "F" followed by a number

appears inthe display, turn off the oven and contact a

qualified technician.

5. Press CANCEL.

If you need Assistance or Service:

Please reference the "Assistance or Service" section of the Use

and Care Guide or contact the dealer from whom you purchased

your built-in oven.

• Household fuse is intact and tight; or circuit breaker has

not tripped.

W10203506A

Printed in U.S.A.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Maytag Four

Maytag

Maytag 27-inch electric built-in single cavity wall... Manuel utilisateur

Maytag

Maytag MEW6530DDW - 30" Convection Single Oven Manuel utilisateur

Maytag

Maytag CWG3100AAS - 24"Gas Single Oven Manuel utilisateur

Maytag

Maytag CWG3100AAB - 24"Gas Single Oven Manuel utilisateur

Maytag

Maytag CWG3600AAB Manuel utilisateur

Maytag

Maytag MEW9630AB Manuel utilisateur

Maytag

Maytag MMV6178AA Manuel utilisateur

Maytag

Maytag CWE4800ACB - 24 Inch Single Electric Wall... Manuel utilisateur

Maytag

Maytag MEW6630DDW - 30" Electric Double Wall Oven Manuel utilisateur

Maytag

Maytag MEW6627DDW - Electric 27 in. Double Wall... Manuel

Maytag

Maytag MMW7530WDS01 Manuel utilisateur

Maytag

Maytag gas wall oven Manuel utilisateur

Maytag

Maytag CWE4800 Manuel utilisateur

Maytag

Maytag MEW7630WDB01 Manuel utilisateur

Maytag

Maytag Wall Oven Manuel utilisateur

Maytag

Maytag MMW7530WD Manuel de la liste des pièces

Maytag

Maytag MEW5527 Manuel utilisateur

Maytag

Maytag W10748894C Manuel utilisateur

Maytag

Maytag MEW7627DH00 Manuel utilisateur

Maytag

Maytag CWE900 Manuel utilisateur

Maytag

Maytag W10669246A Manuel utilisateur

Maytag

Maytag 4348178 Manuel utilisateur

Maytag

Maytag MEW7530DE Manuel utilisateur

Maytag

Maytag MEW6627 Manuel utilisateur

Manuels Four populaires d'autres marques

Bosch

Bosch HVA531NS0 Manuel utilisateur

Electrolux

Electrolux EOF6P46X Manuel utilisateur

NEFF

NEFF B44S32 5GB Series Manuel utilisateur

Combi

Combi BLODGETT BC142GDS Manuel utilisateur

AEG

AEG COMPETENCE 311704300 Manuel utilisateur

Falcon

Falcon DOMINATOR PLUS G3106 Series Guide de l'utilisateur

Rational

Rational SCC WE 61G Manuel utilisateur

Smeg

Smeg DOSPA38X Manuel d'installation et d'exploitation

Electrolux

Electrolux air-o-convect 20 GN 2/1 Manuel utilisateur

Miele

Miele HR 1954-2 Manuel utilisateur

KHIND

KHIND OT50 Manuel utilisateur

Henny Penny

Henny Penny Smoker Box Manuel utilisateur

Lang

Lang ECOD-AP Manuel utilisateur

AEG

AEG BEK455310M Manuel utilisateur

Frigidaire

Frigidaire FNGE90JGR Manuel utilisateur

Hotpoint

Hotpoint FE9 S831 JSH IX Manuel utilisateur

GE Advantium SCB2000 Manuel utilisateur

AEG

AEG DE401301DM Manuel utilisateur