Maxxess EMAX-MR62e Manuel utilisateur

eMAX-MR62e

OSDP READER INTERFACE

MODULE

Installation Guide and Specifications

This device complies with FCC Part 15, Class A Specifications.

The device meets CE Specifications, and is RoHS Certified.

This device is UL 294 Recognized. February 2019 ber, 2011

February, 2019 eMAX-MR62e-Man Page 2 of 16

TABLE OF CONTENTS

Paragraph Title Page No.

1. General …………………………………………………………………………………………….. 3

2. eMAX-MR62e Hardware ……………………………………………….……………………...… 4

3. eMAX-MR62e Terminal Blocks & Jumpers …………..…………………………………...… 5

4. Bulk Erase Configuration Memory ……………………………………………………………. 6

5. Input Power ……………………………………………………………….……………………….. 7

6. Communication Wiring …………………………………………………………………………. 7

7. OSDP Reader Wiring …………………..……………………………………………………….. 7

8. Input Circuit Wiring ………………………………………….………………………………….. 8

9. Relay Circuit Wiring ………………………………………………….………….……………… 8

10. Status LEDs ………………………….………………………………………………………...… 9

11. IT Security ………………………………………………………………………………………… 9

12. Specifications …………………………………………………………………...………………. 10

13. Additional Mounting Information ……………………………………………………….…….. 11

14. Warranty and Liability ………………..……………………………………………………….. 12

Appendix A –Configuring the eMAX-MR62 Network …………………………………………… 13

Change History:

Original Document Original February 2019

February, 2019 eMAX-MR62e-Man Page 3 of 16

1. General:

The eMAX-MR62e OSDP Reader Interface Module provides a network connected interface to

control two physical barriers using OSDP readers, and provides a solution for Maxxess

Installers/Integratosr for interfacing to OSDP readers and door hardware. The on-board Ethernet

with PoE/PoE+ support enables easy installation. The eMAX-MR62e supports up to four OSDP

readers configured as paired or alternate readers.

Note: For UL, the Power Sourcing Equipment (PSE) such as a PoE/PoE+ enabled network switch

and/or PoE/PoE+ power injectors must be UL Listed under UL294B.

One serial 2-wire RS-485 data communication port is available and can accommodate up to four

OSDP readers that are controlling two (2) portals (In/Out paired reader mode). Four Form-C Relay

Outputs may be used for door strike control or alarm signaling. The relay contacts are rated at 2 A

@ 30 Vdc resistive, and are in a dry contact configuration.

Six inputs are provided that may be used for monitoring the door contacts, exit push buttons, and

alarm contacts. Input circuits can be configured as unsupervised or supervised. The eMAX-MR62e

requires PoE, PoE+ or local 12 Vdc for power. The eMAX-MR62e may be mounted in a 3-gang

switch box with the mounting plate that is supplied with the unit. Or it can be mounted in a standard

Maxxess enclosure. The supplied mounting plate has mounting holes that match the MR50

mounting footprint.

February, 2019 eMAX-MR62e-Man Page 4 of 16

2. eMAX-MR62e Hardware:

TB5

IN1 IN2 IN3 IN4 IN5 IN6

VO GNDVINGND

VIN POEJ5

NO NC2-CNONC1-C NO NC4-CNONC3-C

K1 K2 K3 K4

RVOGND TR- TR+

J3 J4

10519-0000-F, REV-A

7 6 5 4 32 1

4 1

INPUTS

RELAYS

J5: INPUT

POWER

SELECT

12 Vdc IN &

AUX POWER

OUTPUT

2.55 [64.77]

5.4 [137.16]

STATUS

LEDs

2.35 [59.69]

2.75 [69.85]

.2 [5.08]

S1: DIP

SWITCH

J3: TAMPER

SWITCH

TO OSDP

READERS

LINK

(GREEN)

SPEED

(YELLOW)

J4: TIA-485

TERMINATION

JUMPER

Ø.125 [3.18]

6 PLACES

EARTH

GROUND

J1: ETHERNET RJ45

CONNECTOR

eMAX-MR62e Layout

February, 2019 eMAX-MR62e-Man Page 5 of 16

3. eMAX-MR62e Terminal Blocks and Jumpers:

MR-51E CONNECTIONS

TB1-1

IN1

Input 1

TB1-2

IN1

TB1-3

IN2

Input 2

TB1-4

IN2

TB2-1

IN3

Input 3

TB2-2

IN3

TB2-3

IN4

Input 4

TB2-4

IN4

TB3-1

IN5

Input 5

TB3-2

IN5

TB3-3

IN6

Input 6

TB3-4

IN6

TB4-1

Auxiliary Power Output –12 Vdc

TB4-2

GND

Auxiliary Power Output Ground

TB4-3

VIN

Input Power –12 Vdc (from local power supply)

TB4-4

GND

Input Power Ground

TB5-1

Relay K1 –Normally Open Contact

TB5-2

1-C

Relay K1 –Common Contact

TB5-3

Relay K1 –Normally Closed Contact

TB5-4

Relay K2 –Normally Open Contact

TB5-5

2-C

Relay K2 –Common Contact

TB5-6

Relay K2 –Normally Closed Contact

TB6-1

Relay K3 –Normally Open Contact

TB6-2

3-C

Relay K3 –Common Contact

TB6-3

Relay K3 –Normally Closed Contact

TB6-4

Relay K4 –Normally Open Contact

TB6-5

4-C

Relay K4 –Common Contact

TB6-6

Relay K4 –Normally Closed Contact

TB7-1

GND

Reader Power Ground

TB7-2

TR-

2-Wire RS-485 TR- (B) See Note 1 below

TB7-3

TR+

2-Wire RS-485 TR+ (A) See Note 1 below

TB7-4

RVO

12 Vdc Reader Power Output

Note 1: Terms A & B are from the RS-485 standard

February, 2019 eMAX-MR62e-Man Page 6 of 16

Jumpers and Jacks:

JUMPER

SET AT

DESCRIPTION

N/A

Ethernet Connection with PoE/POE+ support

N/A

Factory Use Only

N/A

Tamper Switch (normally open contact) See section

14.

N/A

RS-485 Termination, install only if the MR62e is at the

end of the communication bus

PoE

MR62e powered from the Ethernet connection

VIN

MR62e powered from an external 12 Vdc power

source connected to TB4-3 (VIN), TB4-4 (GND)

J6 –J13

N/A

Factory Use Only

DIP Switches:

The four switches on S1 DIP switch configure the operating mode of the eMAX-MR62e Module. DIP

switches are read on power-up except where noted.

Definitions

OFF

Normal operating mode.

OFF

After initialization, enable default User Name (admin) and Password

(password). The switch is read on the fly, no need to re-boot. See IT

Security section for additional information.

OFF

Use factory default communication parameters.

OFF

Use OEM default communication parameters. Contact system

manufacture for details. See Bulk Erase section below.

OFF

Bulk Erase prompt mode at power up. See Bulk Erase below.

All other switch settings are unassigned and reserved for future use. (X = don’t care)

Factory Default Communication Parameters:

Network: static IP address: 192.168.0.251

Subnet Mask: 255.255.255.0

Default Gateway: 192.168.0.1

4. Bulk Erase Configuration Memory:

The bulk erase function can be used for the following purposes:

➢Erase all configuration, sets MR62e to OEM setting (sanitize board).

➢Restore to OEM default parameters.

Bulk Erase Steps: Do not remove power during steps 4-6.

1. Set S1 DIP switches to: 1 & 2 "ON", 3 & 4 "OFF".

2. Apply power to the MR62e.

3. Watch for LEDs 1 & 2 and 3 & 4 to alternately flash at a 0.5 second rate.

4. Within 10 seconds from applying power, change switches 1 or 2 to "OFF". If these switches are

not changed, the MR62e will power up using the OEM default communication parameters.

5. LEDs 1 and 2 alternately flash at a 0.5 second rate while the memory is being erased.

6. Once the memory is eased, LED 1 will be on for about 3 seconds, then the eMAX-MR62e will

reboot.

February, 2019 eMAX-MR62e-Man Page 7 of 16

5. Input Power:

The eMAX-MR62e is powered by one of two ways (jumper selected, J5):

•Power is supplied via the Ethernet connection using PoE or PoE+.

•Local 12 Vdc power supply, TB4-3 (VIN), TB4-4 (GND).

6. Communication Wiring:

Communication between the LP/ EP controller and the eMAX-MR62e is Ethernet (10Base

T/100Base-TX).

It is not recommended to connect the eMAX-MR62e to a public intranet.

7. OSDP Reader Wiring:

Connector TB7 of the eMAX-MR62e Module has connections for the 2-wire RS-485 OSDP

communication bus as well as 12 Vdc to power the OSDP readers. Up to four (4) OSDP readers are

supported on the eMAX-MR62e. The four (4) Readers can be used to control two (2) Doors/Portals

in an In/Out (paired) Reader mode for each door. The 12 Vdc output is limited to .5 A maximum.

The OSDP reader wiring diagram below shows the use of a 2-pair cable for data and power. If this

cable cannot support the voltage/current requirements, a 1-pair cable of sufficient gauge must be

used for power. See specification section.

The RS-485 termination jumper, J4, is only installed if the eMAX-MR62e is at one end of the

communication bus. Only devices at each end of the communication bus are terminated. Never

install termination to more than two devices on the communication bus.

When powering any remote device(s) by the eMAX-MR62e, care must be taken not to exceed the

maximum current available. Cable gauge must also be evaluated. See specifications section for

details.

Reader Wiring Diagram:

TR+ (A)

RVO

TR- (B)

GND

TR- (B)

GND

TB7

12 V

J3 J4

J4: INSTALL ONLY IF MR62e IS AT THE

END OF THE COMMUNICATION BUS

TR+ (A)

GND

TR- (B)

12 V

TR+ (A)

GND

TR- (B)

12 V

TR+ (A)

GND

TR- (B)

12 V

SHIELD: CONNECT TO

EARTH GROUND,

ONE END ONLY!

Typical OSDP Reader Wiring

February, 2019 eMAX-MR62e-Man Page 8 of 16

8. Input Circuit Wiring:

The eMAX-MR62e provided Six (6) inputs that are typically used to monitor door position, request to

exit, or alarm contacts. Input circuits can be configured as unsupervised or supervised. When

unsupervised, reporting consists of only the open or closed states.

When configured as supervised, the input circuit will report not only open and closed, but also open

circuit, shorted, grounded*, and foreign voltage*. A supervised input circuit requires two resistors be

added to the circuit to facilitate proper reporting. The standard supervised circuit requires dual 1K

Ohm, 1% resistors and should be located as close to the sensor as possible. Custom end of line

(EOL) resistances may be configured via the host software.

NOTE: Grounded and foreign voltage states are not a requirement of UL 294 and therefore not

verified by UL.

The input circuit wiring configurations shown are supported but may not be typical:

1K,1%

Standard Supervised Circuit,

Normally Closed Contact

Standard Supervised Circuit,

Normally Open Contact

Unsupervised Circuit,

Normally Open Contact

Unsupervised Circuit,

Normally Closed Contact

TB2

IN4

IN2

IN3

IN1

TB1

}

9. Relay Circuit Wiring:

The eMAX-MR62e includes four (4) relays with Form-C contacts (dry) that provide for controlling door

lock mechanisms or alarm signaling. Each relay contact is rated at 2A @ 30Vdc resistive. When

controlling the delivery of power to the door strike, the Normally Open and Common poles are

typically used. When momentarily removing power to unlock the door, as with a mag lock, the

Normally Closed and Common poles are typically used. Check with local building codes for proper

egress door installation.

Door lock mechanisms can generate feedback to the relay circuit that can cause damage and

premature failure of the relay. For this reason, it is recommended that a diode be used to protect the

relay. Wire should be of sufficient gauge to avoid voltage loss.

It is possible for the eMAX-MR62e to provide power for a 12 Vdc door strike providing the maximum

current is not exceeded. See specification section.

TB5

DIODE SELECTION:

DIODE Current Rating > 1 X STRIKE CURRENT

DIODE Break Down Voltage: 4X STRIKE VOLTAGE

FOR 12VDC or 24VDC STRIKE, DIODE 1N4002

(100V /1A) TYPICAL

February, 2019 eMAX-MR62e-Man Page 9 of 16

10. Status LEDs:

At Power-up, LED 1 turns ON then LEDs 2 through 7 are turned ON then OFF in sequence.

The following table describes the LED’s in the Normal Running mode:

LED

DESCRIPTION

On-line = four pulses per second; 0.1 second ON, 0.1 second OFF, OFF for .3 seconds

Off-line: 0.2 second ON, 0.8 second OFF

Waiting for application firmware to be downloaded: .1 sec ON, .1 sec OFF

Input IN1 Status: OFF = Inactive, ON = Active, Flashing = Fault. See note 2

Input IN2 Status: OFF = Inactive, ON = Active, Flashing = Fault. See note 2

Input IN3 Status: OFF = Inactive, ON = Active, Flashing = Fault. See note 2

Input IN4 Status: OFF = Inactive, ON = Active, Flashing = Fault. See note 2

Input IN5 Status: OFF = Inactive, ON = Active, Flashing = Fault. See note 2

Input IN6 Status: OFF = Inactive, ON = Active, Flashing = Fault. See note 2

J1-YELLOW

Ethernet speed: OFF = 10 Mb/S, ON = 100 Mb/S

J1-GREEN

OFF = No Link, ON = Good Link, Flashing = Ethernet Activity

Note 2: If this input is defined, every three seconds the LED is pulsed to its opposite state for 0.1

second, otherwise, the LED is off.

11. IT Security

When installing When installing the eMAX-MR62e, it is important to ensure that it is done in a secure

manner.

Upon installation, the user accounts to the web configuration page should be created with secure

passwords, and that all DIP switches are in the off position for the normal operating mode. The

eMAX-MR62e is shipped from the factory with a default login account, which is enabled when DIP 1

is moved from OFF to ON. The default login user name and password will be available for five

minutes once enabled. Therefore, it is important that at least one user account is defined, and the

DIP switches are set to OFF before the MR62e is commissioned. It is also highly recommended not

to configure the MR62e with an IP address that is accessible from the public Internet.

To further enhance network security, options are available to disable Zeroconf discovery, as well as

the web configuration module itself.

February, 2019 eMAX-MR62e-Man Page 10 of 16

12. Specifications:

The eMAX-MR62e is for use in low voltage, Class 2 circuits only.

Power Input: PoE (12.95 W), compliant to IEEE 802.3af

PoE+ (25 W), compliant to IEEE 802.3at

12 Vdc 10 %, 1.7 A maximum

For UL, the Power Sourcing Equipment (PSE) such as a PoE/PoE+ enabled network switch and/or

PoE/PoE+ power injectors must be UL Listed under UL294B. Wiring for the 12V input shall not

extend more than 30m from the product.

Power Output: PoE: VO (TB4-1) and RVO (TB7-4), combined: 12 Vdc @ .66 A

maximum

PoE+ or 12 Vdc: VO (TB4-1) 12 Vdc @ 1 A maximum, RVO, (TB7-4) 12

Vdc @ .5 A maximum

Output: Four relays, Form-C contacts rated at 2 A @ 30 Vdc

Inputs: Six unsupervised/supervised, End of Line resistors, 1k/1k ohm, 1%, ¼

watt standard

Reader Interface:

Power: 12 Vdc @ .5 A maximum (RVO, TB7-4)

Communication: 2-Wire RS-485, OSDP protocol, four devices maximum

Cable Requirements:

Communication: Ethernet, Category 5, minimum

External Input Power: 1 twisted pair, 18 AWG (if required)

Alarm Inputs: 1 twisted pair per input, 30 ohm maximum

Relay Outputs: As required for the load

Reader Data RS-485/power: 2 twisted pair with shield, 24 AWG, 120 ohm impedance

and Power* 4000 foot (1220 m) maximum.

RS-485: 1 twisted pair with shield, 24 AWG, 120 ohm impedance, 4000

foot (1220 m) maximum

and

power: 1 pair 18 AWG*

* Type of cable(s) and gauge determined by length and voltage/current

requirements. Local power source may be required.

Environment:

Temperature: -55 to +85 C, storage

0 to +70 C, operating

Humidity: 5 to 95 % RHNC

Table des matières

Autres manuels maxxess Unité de contrôle

maxxess

maxxess eMAX-MR51e Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur

maxxess eMAX-MR62e Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques