Maxim MAX3866 Manuel utilisateur
Electrical Quick Start
1) Attach matched 50ΩSMA cables from a 50Ωoscillo-
scope to OUT+ and OUT-. Set the oscilloscope to
20mV/div and 200ps/div. A single-ended evaluation
is acceptable; however, the cable not terminated
into the scope should be terminated with a 50Ωload
at the end of the cable.
2) Ensure that there is a shunt across the VCCS pins.
(Remove shunt for 5.0V operation.)
3) Attach ground to either side of the GND 2-pin
header and +3.3V (or +5.0V) to either side of the
VCCD 2-pin header.
4) Connect a 50Ωcable between the output of a 50Ω
source and the input of the EV kit. Set the source to
produce a 2.0Vp-p, 2.5Gbps 1-0 pattern.
5) Adjust R9 and R6 to produce a DC current of 1mA
(1mA = 2.0Vp-p / 1kΩ/ 2) through R7. This can be
verified by checking for a 1V drop across R7.
6) Verify that the input pattern is present at the output.
General Description
The MAX3866 evaluation kit (EV kit) is a fully assem-
bled, chip-on-board (COB) electrical demonstration kit.
It provides easy evaluation of the MAX3866 2.5Gbps,
+3.3V combined transimpedance/limiting amplifier.
Features
♦Easy +3.3V or +5.0V Electrical Evaluation of
MAX3866
♦Evaluation of Adjustable Loss-of-Power (LOP)
♦Fully Assembled and Tested
♦EV Kit Designed for 50ΩI/O Interface
Evaluates: MAX3866
MAX3866 Evaluation Kit
________________________________________________________________
Maxim Integrated Products
1
19-1451; Rev 0; 3/99
SUPPLIER PHONE FAX
AVX 803-946-0690 803-626-3123
Component List
Central Semiconductor 516-435-1110 516-435-1824
Murata 814-237-1431 814-238-0490
Zetex 516-543-7100 516-864-7630
PART
MAX3866EVKIT -40°C to +85°C
TEMP. RANGE
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800.
For small orders, phone 1-800-835-8769.
Ordering Information
Component Suppliers
SMA connectors (edge mount)
E.F. Johnson 142-0701-801 or
Digi-Key J502-ND
3
INPUT (J1),
OUT+ (J4),
OUT- (J5)
LED1CR1
1MΩpotentiometer1R9
1kΩpotentiometer1R6
49.9Ω, 1% resistors (0402)2R5, R8
1kΩ, 1% resistors (0402)2R3, R7
DESIGNATION
150Ω, 1% resistor (0402)1R2
500Ωpotentiometer1R1
1µH inductor
Coilcraft 1008CS-102 XKBB, 10%
1L1
Leave site open0
C9, J2, J3, L2,
R4, R10, R11,
R12, TP2, TP3
100nF, 25V min, 10% ceramic capaci-
tors (0603)
7
C1, C2, C3,
C5–C8
DESCRIPTIONQTY
Test point
Mouser 151-203
1LOP
2-pin headers (0.1" centers)
Digi-Key S1012-36-ND
3
VCCS, VCCD,
GND
Shunt (installed)
Digi-Key S9000-ND
1VCCS
MAX3866E/D1U1
MAX3866 circuit boards, Rev. B2None
MAX3866 data sheet1None
MAX3866 EV kit data sheet1None
0.5" spacers3None Screws for the spacers6None
Note: Please indicate that you are using the MAX3866 when
ordering from these suppliers.
Evaluates: MAX3866
MAX3866 Evaluation Kit
2 _______________________________________________________________________________________
Adjustment and Control Description
CONTROL NAME FUNCTION/MANIPULATION
VCCD VCCD Power-Supply Voltage. Both pins of this dual-pin header are the same
point.
VCCS VCCS
Power-Supply Select Jumper. Do not apply any external voltages at
this point. Both pins of this 2-pin header are not connected electrically.
Depending on what the operating voltage is, either place a shunt at
VCCS or remove the shunt from VCCS. When evaluating at 3.14V to
3.47V, ensure that there is a shunt on VCCS. If the evaluation voltage is
5.0V to 5.5V, remove this shunt and place a 100nF capacitor in location
C8. (EV kit is shipped with 100nF in the C8 location; see
Figure 1
.)
J1 INPUT Single-Ended Input, 3mVp-p to 2.5Vp-p range. This translates into a
current of 3µA to 2.5mA, respectively (voltage at input) / (R3 = 1kΩ).
Note that the EV kit input is terminated for a 50Ωsource.
J4, J5 OUTP, OUTM Signal Outputs (AC-coupled). Note that the EV kit outputs are designed
for 50Ωtermination.
R6, R9 —
Micro and Macro Current Adjustment. Simulates the average DC
current portion of a diode. The amount of current that should be set
through these potentiometers is calculated by the formula (AC current
into MAX3866) / 2 = DC bias current.
CR1 DIODE LOP is active high. Therefore, when an LOP condition exists, the LED
will be off.
TP1 LOP TTL Output, active high. Probe this test point only with a high-imped-
ance lead.
R1 —
Sets the LOP Threshold. For normal operation, Maxim recommends R8
+ R1 = 510Ω. However, if other values are desired, please refer to the
Typical Operating Characteristics
section (Assert/Deassert vs. RPD) of
the MAX3866 data sheet.
SJ2 — Solder Jumper. For normal operation, ensure that this solder jumper is
open.
Evaluates: MAX3866
MAX3866 Evaluation Kit
_______________________________________________________________________________________ 3
CHF-
FIL-
GND
GND
R3
1k
R6
1k
SJ2
SOLDER JUMPER
OPEN
R9
1M
L1
1µH
L2
OPEN
R11
OPEN
R12
OPEN
C9
OPEN
R10
OPEN
ZO= 50
2
1
1
1F
2
2
1FF1
22
3
GND
GND
3
C3
100nF
R7
1k
INPUT
J1
SMA
ZTEST1
J2
SMA
ZTEST2
J3
SMA
R5
50Ω
LINE TERMINATION
GND
IN+
IN-
GND
N.C.
R8
50Ω
R1
500Ω
C2
100nF
1
3
2
GND
OUT+
OUT-
GND
LOP
CHF+ VCCS VCCS VCCD VCCD LOP R2
150Ω
R4
OPEN
CR1
DIODE VCCD
2
1GND
P2
VCCD
P1 (3.13V... 3.47V OR
4.5V....5.5V)
2
VCCD
C8
100nF
VCCS
(C8 IS NOT REQUIRED
IN 3.3V OPERATION.)
C7
100nF
C1
100nF
12 1
C5
100nF
OUT+
J4
SMA OUT-
J5
SMA
12
1
2
C6
100nF
PDC INV GND GND CPD- CPD+
MAX3866
U1
Figure 1. MAX3866 EV Kit Schematic
Evaluates: MAX3866
MAX3866 Evaluation Kit
4 _______________________________________________________________________________________
Figure 2. MAX3866 EV Kit Component Placement Guide—
Component Side
1.0"
Evaluates: MAX3866
MAX3866 Evaluation Kit
_______________________________________________________________________________________ 5
Figure 3. MAX3866 EV Kit PC Board Layout—Component Side Figure 4. MAX3866 EV Kit—Ground Plane
1.0"
1.0"
Evaluates: MAX3866
MAX3866 Evaluation Kit
6 _______________________________________________________________________________________
Figure 5. MAX3866 EV Kit—Power Plane Figure 6. MAX3866 EV Kit PC Board Layout—Solder Side
1.0"1.0"
Evaluates: MAX3866
MAX3866 Evaluation Kit
_______________________________________________________________________________________ 7
Figure 7. MAX3866 EV Kit—Bond Diagram
1.0"
HF23Z
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
8
_____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 1999 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.
Evaluates: MAX3866
MAX3866 Evaluation Kit
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
8
_____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 1999 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.
NOTES
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
8
_____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 1999 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.
Table des matières
Autres manuels Maxim Carte mère
Maxim
Maxim MAX16920A Instructions d'utilisation et d'entretien
Maxim
Maxim MAX9995 Manuel utilisateur
Maxim
Maxim MAX3296 Manuel utilisateur
Maxim
Maxim MAX7349 Manuel utilisateur
Maxim
Maxim MAX5022EVKIT Instructions d'utilisation et d'entretien
Maxim
Maxim MAX2654 Manuel utilisateur
Maxim
Maxim MAX2385EVKIT Manuel utilisateur
Maxim
Maxim MAX9264 Manuel utilisateur
Maxim
Maxim MAX3287 Manuel utilisateur
Maxim
Maxim MAX16831 Manuel utilisateur
Maxim
Maxim MAX1455 Manuel utilisateur
Maxim
Maxim MAX9982 Manuel utilisateur
Maxim
Maxim MAX2745 Manuel utilisateur
Maxim
Maxim MAX11835 Manuel utilisateur
Maxim
Maxim MAX5971B Manuel utilisateur
Maxim
Maxim MAX16839 Manuel utilisateur
Maxim
Maxim MAX1402 Manuel utilisateur
Maxim
Maxim MAX9993 Manuel utilisateur
Maxim
Maxim MAX2741 Instructions d'utilisation et d'entretien
Maxim
Maxim MAXQ7665 Manuel utilisateur
Manuels Carte mère populaires d'autres marques
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuel utilisateur
Gigabyte
Gigabyte GA-9IVDT Manuel utilisateur
Texas Instruments
Texas Instruments ADS8372EVM Manuel utilisateur
Commell
Commell MS-C73 Manuel utilisateur
IBT Technologies
IBT Technologies MB860 Manuel utilisateur
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur
