Matrix SETU VGFX Manuel utilisateur

SETU VGFX

Quick Start

SETU VSETU V

SETU VGFXGFX

GFXGFX

GFX

VoIP-GSM-FXS-FXO Gateway

Quick Start

Introduction

Thank you for choosing Matrix SETU VGFX! Please read the instruction in this

quick start to install this feature reached system.

This Quick Start is meant to help you to install the basic features and parameters

of VGFX. For detailed information on installing and configuring SETU VGFX,

please refer 'SETU VGFX V1 System Manual' provided to you on the CD-ROM.

Know your SETU VGFX

SETU VGFX has 1 WAN Port, 2 FXO Ports, 2 FXS Ports, 4 Mobile Ports, 9 SIP

Trunks, Antenna Connecter, a Power Socket and 10 LEDs.

SETU VGFX is available in three different configurations:

1. SETU VGFX8422: supports 4 Mobile Ports, 2 FXO Ports and 2 FXS Ports.

This is the default configuration of SETU VGFX.

2. SETU VGFX8404: supports 4 Mobile Ports and 4 FXS Ports.

3. SETU VGFX8440: supports 4 Mobile Ports and 4 FXO Ports.

This Quick Start is written with reference to the default configuration. The term

SETU VGFX refers to SETU VGFX8422, unless otherwise specified.

LEDs:

There are total 10 LEDs in VGFX. These LEDs are labeled as M1, M2, M3, M4,

P1,P2,P3,P4, STSand PWRas shownin thefigure below. These LEDs indicate

the status of ports, various events occurring on the ports and also the error

conditions.

M1 M2 M3 M4 Power

P1 P2 P3 P4 Status

All LEDs are of dual colour (Red/Green) except Power LED which is of single

colour (Red). Power (PWR) and Status (STS) LEDs are non-programmable

whereas all port LEDs are programmable.

By default, LEDs labeled as M1, M2, M3 and M4 show status of Mobile

Ports. LEDs labeled as P1 and P2 show status of FXO Ports and P3 and P4

show status of FXS Ports.

Port LEDs can be programmed for showing the status of SIP Trunks also.

You can program LEDs for showing status of maximum 8 SIP Trunks

simultaneously. (Refer "Step 10" for more details)

Before You Start

Verify Package Contents

SETU VGFX with Antenna

(Rubber ducky SMA)

Quick Start and User Card CD containing System Manual,

Quick Start and User Card

Adaptor 12VDC, 2A

(Country Specific)

Two Screws M 7/30 with Grips

External Antenna SMAwith cable

AWarranty Card Set

AMounting Template

Ethernet Cable (RJ45)

Makesure that all the above mentioned componentsare present when you open

the Sales Kit of SETU VGFX. In case any of the part is missing or damaged,

contact the source from where you have purchased your VGFX.

Get your Internet Connection ready:

To install VGFX, you must have:

1. BroadbandInternet connection fromanISP tomakeand receive callsthrough

public internet. If you want to make calls within your network, you do not

need an internet connection.

2. Connection from an Internet Telephony Service Provider (ITSP) to activate

your SIP Trunks. You do not need an ITSP connection for making Peer to

Peer calls.

Get your Network Information ready:

Ask your LAN Administrator/ISP for:

1. IP Address

2. Subnet Mask

3. Gateway Address

4. DNS Address

5. DNS Domain Name

Ask your ITSP for:

1. SIP ID/User ID

2. Authentication User ID (in most cases it is same as SIP ID)

3. Authentication Password

4. Registrar Server Address

5. Registrar Server Port

6. Outbound Proxy Server Address

7. Outbound Proxy Server Port

To install VGFX, you should also have:

1. An active SIM card/s from GSM service provider.

2. Analog trunk line from Public Switched Telephone Network (PSTN).

Installing SETU VGFX

Take proper precautions while installing VGFX to reduce the risk of fire, electric

shock and injury to the system as well as the person using it. (Refer Installation

Precautions and Safety Instructions under 'Protecting SETU VGFX' topic in the

System Manual)

Mounting SETU VGFX on wall:

SETU VGFX should be installed at the airy, dust free and moisture free place.

• Select a suitable place on the wall for mounting SETU VGFX.

• Put the mounting template on the wall and mark the nail hole on the wall.

• Drill a hole of appropriate size.

• Insert the screw and tighten it leaving the screw head a few millimeters

protruded of the wall.

• Check the strength of the nail.

• Hang VGFX on the wall.

Connecting SETU VGFX

Connect SETU VGFX as shown below:

Router

RJ11

Adaptor

Ethernet

Switch

RJ11 Antenna

• Place SETU VGFX at a suitable place where it can be provided with proper

power supply.

• Connect Ethernet (WAN) Port of SETU VGFX to the LAN Switch/Network of

the Enterprise.

• Connect PSTN line to the FXO Port of SETU VGFX or connect FXO Ports of

SETU VGFX to the FXS Ports of the PBX.

• Connect telephone instruments to the FXS Ports of SETU VGFX or connect

FXS Ports of SETU VGFX to the FXO Ports of the PBX.

• Connect Antenna to SETU VGFX.

• Insert SIM Card into the Mobile Port of SETU VGFX for the mobile network.

If SIM protection is enabled in the SIM Card, ensure that SIM PIN of the SIM

Card and VGFX is same. By default, SIM PIN of all the Mobile Ports of the

VGFX is 1234. To change SIM PIN of the SIM Card, SE is recommended to

take following steps:

• Switch Off VGFX.

• Remove SIM Card and insert the same in the mobile instrument.

• Enable 'SIM PIN at Power ON' parameter in the SIM Card. (This step is

not required if SIM protection is already ON)

• Change the SIM PIN of the SIM Card to 1234 i.e. the default SIM PIN of

VGFX.

• Remove SIM Card from the mobile instrument and insert it in VGFX.

• Change the SIM PIN after VGFX attains normal working position.

• Connect Power Socket of SETU VGFX to the power supply using 12V DC,

2A power adaptor.

Switching ON SETU VGFX

After connecting SETU VGFX as shown above, switch ON the power supply.

At Power ON, Power LED will turn ON (Continuous Red). Initialization process

will start and LED sequence of all other LEDs during initialization process is

shown in the table given below:

System Status STS P1 P2 P3 P4 M1 M2 M3 M4 Time in MS

Power ON - UBOOT OFF ON OFF OFF OFF OFF OFF OFF OFF

Kernel UP & LED Driver

Loaded OFF ON ON OFFOFFOFFOFFOFFOFF

Application Load OFF ON ON ON OFF OFF OFF OFF OFF 200ms

VOPP Program

Download Success OFF ON ON ON ON OFF OFF OFF OFF 200ms

All Init Done, System

goes Live ON ON ON ON ON ON ON ON ON 1000 ms

ON ON ON ON ON ON ON ON ON 1000 ms

OFF OFF OFF OFF OFF OFF OFF OFF OFF 1000 ms

ON OFFOFFOFFOFFOFFOFFOFFOFF 1000 ms

OFF OFF OFF OFF OFF OFF OFF OFF OFF 1000 ms

(Continuous

Last 2 steps)

Red color text (Bold) indicates that led will glow red and Green color text

(Bold+Italic) indicates that led will glow green.

Mobile Port LEDs (M1, M2, M3 and M4) will display following error/event/status

during initialization:

Event/State/

Status Color Cadence (in ms) (1 cadence is of 4000ms)

GSM Initialization Red 500ms On- 500ms Off – 500ms On-500ms Off-

500msOn-500ms Off- 500ms On- 500ms Off (4

Blinks)

PUK required Red 500ms On- 500ms Off – 500ms On-500ms Off-

500msOn-1500ms Off (3 Blinks)

SIM PIN faulty Red 500ms On- 500ms Off – 500ms On-2500ms Off (2

Blinks)

SIM Absent Red 500ms On- 3500ms Off (1 Blinks)

GSM network

absent Red 1sec On – 1sec Off

System LED (STS) will display the following error/events/status:

System Status LED Status Comment

VoPP Program Down

Load Fail. Red On Continuously VoPP Program download

fail

Gateway started

successfully and

NW_Up_SIP_Up_CDR

_OK

GREEN Blink

1sec On-1sec Off Gateway Started

Successfully.

Network link is Up. SIP

stack is Up CDR buffer is

not full

NW_Down_SIP_

down_CDR_OK Green Blink

500 ms on-500ms off-500

ms on-500ms off-500 ms

on-500ms off- 500 ms on-

500ms off

Network link is down. SIP

stack is down CDR buffer

is not full

NW_Up_SIP_down_C

DR_OK Green Blink

500 ms on-500ms off-500

ms on-500ms off- 500 ms

on-1500ms off

Network link is Up.

SIP stack is down CDR

buffer is not full

NW_Down_SIP_

down_CDR_Full Red Blink

500 ms on-500ms off-500

ms on-500ms off-500 ms

on-500ms off- 500 ms on-

500ms off

Network link is down. SIP

stack is down CDR buffer

is full

NW_Up_SIP_down_C

DR_Full Red Blink

1sec On-1sec Off Network link is up.

SIP stack is up CDR

buffer is full

NW_Up_SIP_Up_CDR

_Full Red Blink

500 ms on-500ms off-500

ms on-500ms off- 500 ms

on-1500ms off

Network link is up.

SIP stack is up CDR

buffer is full

FXS/FXO/Mobile Port LED status during normal functioning is as shown below:

ON OFF ON OFF

Port Idle/Disable -

Incoming Ring Event Red 400 200 400 3000

Off-Hook Event Red

Speech Green Continuous

Continuous

Event/State/Status Color Cadence (1 cadence is of 4000ms)

OFF

LED of FXS Port, that is used to enter the programming mode, will glow

continuous GREEN while the system is in programming mode. Once the

command to exit programming mode is issued, the LED will turn continuous

RED i.e. will display the Off-Hook Event.

You can also program Port LEDs for showing the status of SIP Trunks. For

example, if you are using only two mobile ports and other two mobile ports are

disabledthen you canprogram these LEDs for showing the status ofSIPTrunks.

(Refer Step 13: 'Checking the Status' for more details)

If LED is programmed for SIP Trunk, it will display following error/event/status:

ON OFF ON OFF

SIP Disable -

SIP Registered Green

SIP Registration

Failed Red

SIP Authentication

Failed Red 200 200 200 3400

Continuous

Event/State/Status Color Cadence (1 cadence is of 5000msec)

OFF

Whenall LEDsare programmedfor SIPTrunks then no LED indication would

be displayed for FXS/FXO and Mobile Port.

Accessing Web Jeeves:

Programming of SETU VGFX can be done using Web JEEVES only. It does not

support programming of VGFX using telephone instrument except few Network

Port Parameters. To access Web JEEVES, Network Port Parameters should be

programmed first using conventional phone. Follow the steps shown below:

Accessingweb jeeves is a very importantstep in programmingVGFX. To access

web jeeves, Network Port Parameters should be programmed first using

conventional phone.

1. Pick up handset of analog phone connected to SETU VGFX.

2. Dialthe programming access code #19 followed by default password 1234.

You will get programming tone.

3. To access Web JEEVES using computer/computers in LAN to which VGFX

is connected, change IP address and Subnet Mask of SETU VGFX to bring

VGFX and computer/computers in LAN in the same subnet. Ensure that

their IP Addresses are different.

4. To program Network Port IP address, use command: 11-IP Address-#*

Where,

IP address is of 12 digits in XXX.XXX.XXX.XXX format. Each octet is of

three digits ranging from 001 to 255. For example, to program IP address

192.168.1.120, enter the command 11-192168001120-#*. By default, IP

Address of VGFX is 192.168.001.176.

Autres manuels pour SETU VGFX

Table des matières

Autres manuels Matrix Porte

Matrix

Matrix SETU VFX88L Guide de l'utilisateur

Matrix

Matrix simado gfx11 Guide de l'utilisateur

Matrix

Matrix SETU VTEP Manuel utilisateur

Matrix

Matrix SETU VFXTH Guide de l'utilisateur

Matrix

Matrix SIMADO GFX44 Guide de l'utilisateur

Matrix

Matrix SIMADO GFX44 Manuel utilisateur

Matrix

Matrix SIMADO GFX44 Guide de l'utilisateur

Matrix

Matrix SETU VFXTH Manuel utilisateur

Matrix

Matrix SETU ATA211 SIP-FXS-FXO Guide de l'utilisateur

Matrix

Matrix SETU VGRX Guide de l'utilisateur

Matrix

Matrix SETU VG Guide de l'utilisateur

Matrix

Matrix SETU VFX88L Manuel utilisateur

Matrix

Matrix SETU VFX Manuel utilisateur

Matrix

Matrix SETU VGFX Manuel utilisateur

Manuels Porte populaires d'autres marques

LST

LST M500RFE-AS Manuel utilisateur

Kinnex

Kinnex Media Gateway Manuel utilisateur

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur

Telsey

Telsey CPVA 500 - SIP Manuel utilisateur

RTA

RTA 460A-NNA4 Fiche technique

Shaw

Shaw Gateway HDPVR Manuel utilisateur

ABB

ABB VSN900 Guide de démarrage rapide

Commander

Commander Pulse Manuel utilisateur

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuel utilisateur

NETGEAR

NETGEAR C6300BD Manuel utilisateur

Amit

Amit CDW531AM Manuel utilisateur

HMS

HMS Netbiter EasyConnect EC150 Manuel utilisateur

Huawei

Huawei EchoLife HG620 Manuel utilisateur

AT&T

AT&T U-verse 3801 Manuel d'utilisation et d'entretien

Logic IO

Logic IO RTCU MX2 turbo Manuel utilisateur

Suttle

Suttle MediaMAX MXM-521 Manuel utilisateur