Mastech MS6508 Manuel utilisateur

MS6508

Temperature Humidity Meter

01 02

Brief Introduction

This is a battery meter for measuring relative

humidity and temperature. It can display three types

of temperatures around the sensor's air via several

convenient procedures: The ambient temperature,

the dew-point temperature and the wet bulb

temperature.

MAXMIN

DEW

POINT

BULB

WET

HO LD M EM

READ

MIN

MEM

C/F

Operation

Notice

When moving the meter from one atmosphere with

extreme temperature or humidity to another, you need

to wait for its stability.

Press to start the meter and read the measurements

displayed by °C or °F.

Press to switch.

Dewpoint & Wetbulb

When starting the meter, the ambient temperature

appears on the screen. To obtain DP, press a first time

, and press DP

for a second time, WB is switched.

back. A corresponding si gnal will b e shown on

the screen indicating DP and WB.

Holding

Hold the button Press H

to freeze the current

reading, and stop the meter from displaying

the measurements. When the

HOL D

(HOLD) function

is actived,the screen displays

HOL D

.To continue reading

the mesured value,press

HOL D

again.

C/F

Press a third time, to get the ambient temperature

MAXMIN

DEW

POINT

BULB

WET

HOL D M E M

Display Screen

NO.

explanation

Low battery

Automatic power-off mark

Display wet bulb temperature or

dew-point temperature

Temperature measurement unit

Relative humidity measurement unit

MEM, RAM position number

Max-min

Hold function actived.The screen

freezes the current reading

FRO N T PANE L

MS6508

Sensor

Dew-point

Wet-bulb

Ambient

temperature

Display

screen

Data holding

Data preserving

Automatic

power-off

Power

Max-min

Data recall

Backlight

Unit switch

MAXMIN

DEW

POINT

BULB

WET

HO LD ME M

READ

MIN

MAX

MEM

C/F

MS650 8

HYS006704

05 06

Automatic power-off

To pr olong the l ife-spa n of the batt ery, this meter

offers an automatic power-off functi on, and it cl oses

without operation in 30 minutes. This function is

approved. Just press if closing it for longer

measurement, and disappears. Do it again, the

automatic power-off is on.

The backlight

Press to start the backlight, press again

to close the backlight. If starting without automatic

power-off, it will close after 15 seconds.

Maintenance

Replace the batteries

The meter is charged with four 1.5(AAA type) batteries.

When appears, the batteries should be replaced as

soon as possible. Follow the instructions:

1. unscrew the top of the entrance.

2. Get th e batteries out.

3. Install four unused AAA batteries in accordance

with polarity descripted at the bottom.

4. reload the entrance and fasten the screw.

07 08

Specification

Ambient temperature

Range: -20 to 60°C (-4 to 140°F)

Precision: ±0.5°C (0 to 45°C)

±1.0°C (-20 to 0°C,45 to 60°C)

Resolution: 0.1°C/°F

Update rate: 400ms

sensor's type: High-Precision digital sensor (SHT75)

Range: 0 to 100%RH

Accuracy : ±3.0% RH (10% to 90%)

±4.0% RH (0% to 10%,90% to 100%)

Resolution: 0.1%

Update rate: 400ms

Sensor's type: High-precision digital sensor

Range: -20 to 60°C (-4 to 140°F)

Precision : ±1.0°C (0 to 45°C)

±1.5°C (-20 to 0°C，45 to 60°C)

Resolution: 0.1°C/°F

Update rate: 400ms

Range: -50 to 60°C (-58 to 140°F)

precision : ±1.0°C (0 to 45°C)

±1.5° C (-50 to 0°C，4 5 to 60°C)

Resolution: 0.1°C/°F

Update rate: 400ms

RAM: 99 data point

Power: 4 AAA batteries

Weight/size: 190g (batteries included)

184mm ×60mm×2 9mm

Max-min

Pressing , Max-min is set up, and max updates

MIN

MAX

constantly, press MIN

MAX again, it is min. The two stations

can be switched. If turn off, you need to press MIN

MAX for

two seconds; a sound shows that this function has been

turned off. Max means that the peak of temperature and

humidity, while min is the lowest reading.

Saving and transferring the measurements

This meter is able to save 99 groups reading for

transferring. Press MEM to save the reading, an d its

location displays at the screen's upper right corner.

After two seconds, the meter comes back to the normal

state; If RAM is filled fully, the meter will cover the

stored data from No.1 RAM and keep the reading.

When transferring the saved figure, press READ to ent er

MEM check-up. At this time, DP

WB and are used to

change the page. To exit it, press READ again. In the state

of check-up, press MEM for five se conds and “ 00”is

displayed at the screen's right upper corner, which

means RAM is cleared.

C/F

Autres manuels Mastech Instrument de mesure

Mastech

Mastech MS2025C Manuel utilisateur

Mastech

Mastech MS20006 Manuel utilisateur

Mastech

Mastech MS2109A Manuel utilisateur

Mastech

Mastech MS8238A Manuel utilisateur

Mastech

Mastech MS2108 Manuel utilisateur

Mastech

Mastech MS2203 Manuel utilisateur

Mastech

Mastech MS6701 Manuel utilisateur

Mastech

Mastech MS2108 Manuel utilisateur

Mastech

Mastech ms6708 Manuel utilisateur

Mastech

Mastech MS2128 Manuel utilisateur

Mastech

Mastech MS2016A Manuel utilisateur

Mastech

Mastech MS2115B Manuel utilisateur

Mastech

Mastech MS2205 Manuel utilisateur

Mastech

Mastech MS3300 Instructions de montage

Mastech

Mastech MS5908C Manuel utilisateur

Mastech

Mastech MS2026 Manuel utilisateur

Mastech

Mastech MS2208 Manuel utilisateur

Mastech

Mastech MS6580 Manuel utilisateur

Mastech

Mastech MS8212A Manuel utilisateur

Mastech

Mastech MS2138/R Manuel utilisateur

Mastech

Mastech MS2225A Manuel utilisateur

Mastech

Mastech MS2010A Manuel utilisateur

Mastech

Mastech MS2026R Instructions de montage

Mastech

Mastech MS8221C Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur