Marshall Amplification JTM45 Manuel utilisateur

From the Chairman

Congratulations on your purchase of the limited

edition reissue of the offset JTM45 halfstack. The

original versions of this amp and cabinet were built

back in 1962, the very year in which Marshall

Amplification was born. In fact, the offset head was the

first version of the JTM45 my company made and only

a mere handful of these heads and cabinets were ever

constructed. In case you are wondering, the reason the

amp's chassis was offset like this was to help ensure

that the head balanced properly when carried. Despite

the practicality of this design however, we quickly

discovered that most people preferred the symmetrical

look of a centrally placed chassis, so that’s how we’ve

been building heads ever since!

A few years ago one of these extremely rare offset

halfstacks came back into my possession and I

immediately placed it in the Marshall Museum at our

headquarters in Milton Keynes, England. Since then, all

who have seen and heard it have commented most

favourably - not only on its unique looks but also on its

rich, fierce, majestic tone.

To celebrate the dawn of a new century I wanted to

offer something truly special - hence this reissue. To

make this unique product as authentic as possible, we

have sought out and reproduced all of the original

components and methods of construction we used back

in 1962. From the hand-wired tag-board circuit housed

in an aluminium chassis, through to the original silver

Celestion Alnico loudspeakers. We have even

resurrected the original ‘coffin’ logo!

I sincerely hope that this eye-catching reissue of one

of the first Marshall amplifiers ever made, will provide

you with countless hours of playing pleasure. I'm sure

it will. I'm also sure it will prove to be a quite a

conversation piece too!

WARNING!

Please read the following list carefully.

A. ALWAYS use the correct power cord

B. NEVER attempt to by-pass the fuses or fit ones of the incorrect value.

C. NEVER attempt to replace fuses or valves with the amplifier connected to the mains.

D. DO NOT attempt to remove the amplifier chassis, there are no user serviceable parts.

E. ALWAYS have this equipment serviced or repaired by competent qualified personnel.

F. NEVER use an amplifier in damp or wet conditions.

G. DO NOT switch the amplifier on without the loudspeaker connected.

H. ENSURE that any extension cabinets used are of the correct impedance.

I. PLEASE read this instruction manual carefully before switching on.

WARNING : This apparatus must be earthed!

WARNING : Do not obstruct ventilation grille and always ensure free movement of air around the amplifier !

KEEP THESE INSTRUCTIONS

Introduction

As Jim has already stated, our goal, when building this limited edition, offset reissue, was simple. To make it as

close to the original as humanly possible! To this end we have gone to great lengths to recreate every single aspect

and specification of this visually and aurally striking item-from sourcing an exact replica of the original coffin logo (so

called because it was first made for us by a coffin manufacturer!), to ensuring that the output and power transformers

boast the same exact core lamination materials as they did back in 1962. Likewise, the amplifier circuit itself is hand-

wired on a hand-built tagboard, the chassis is constructed from aluminium and the valve complement is 3 x ECC83s

in the preamp, a GZ34 rectifier and a pair of KT66s in the power amp - just like the original.

We are delighted to report that many of our suppliers went to the same exacting lengths as we did when providing

us with parts for this reissue, and none-more-so than Celestion. Thanks to their commitment to this project they

successfully recreated the Alnico magnet, silver G12, model T0652 loudspeakers found in our museum piece-right

the way down to matching the same exact colours and lettering fonts used on the original label!

As is the case with all our amplifiers, the best way for you to truly appreciate this remarkable reissue is to grab

your favourite guitar, plug it in and play. Enjoy!

JTM45 O/S Front and Rear Panel Features

Front Panel Functions

The JTM45 O/S features four inputs, two per channel. The first channel is voiced for a high treble response with the

second channel voiced for normal response. The first input of each channel has more gain than the second input of

each channel and hence is louder. Though the first input of the first channel is the input that most guitarists use,

don’t hesitate to experiment. Some guitar players prefer to mix

the two channels by putting a patch lead between the second

input of channel 1 and the first input of channel 2 and then plug

their guitar into the first input of channel 1. Doing this allows

you to mix the different tonal characters of each channel for

greater flexibility.

See Diagram right.

Front Panel Functions

1. Power Switch

On / Off Switch for mains power to the amplifier.

2. Standby Switch

Controls H.T. or high voltage to the valves to allow

them to attain correct working temperature before

playing. To prolong the life of the valves it is

always advisable to switch on the Mains Power

Switch (item 1) about 2 minutes before switching

on the Standby (item 2).

On switching off, the Standby should always be

switched before the Power Switch.

The standby facility is particularly useful live

between sets and before playing, as it allows you to

keep the valves operating at a functional

temperature but without any sound being

produced.

3. Presence Control

Adds higher frequencies to the guitar tone, creating

crispness and bite. Turning this up will make the

sound more cutting and further forward.

4. Bass Control

Controls the amount of low frequencies or bottom

end in your tone.

5. Middle Control

Dictates the middle register of the amplifier.

Turning this up will make your guitar sound fatter.

Conversely reducing the amount of middle in your

tone will result in a sharper and thinner guitar

sound for the classic ‘scooped’ tone.

6. Treble Control

Controls the high frequencies of the guitar tone,

making your guitar sound brighter when increased.

7. Volume I

Controls the overall output level of channel 1.

Note - this channel is voiced for a higher treble

response than channel 2.

8. Volume II

Controls the overall output level of channel 2.

Note - channel 2 is voiced for normal response.

9. Input Jack

Connects the guitar to channel 1.

10.Input Jack

Connects the guitar to channel 1.

Note - this input has less gain than item 9.

11. Input Jack

Connects the guitar to channel 2.

12. Input Jack

Connects the guitar to channel 2.

Note - this input has less gain than item 11.

Rear Panel Functions

1/2. Loudspeaker Jacks

With all valve amplifiers it is imperative that the

amp is connected to a load whilst in operation and

that the impedance selected on the amp matches

the total impedance of the speaker cabinet(s) being

used. For example, if the amp is running into a

single 16 Ohm cab, the amp should accordingly be

set to 16 Ohms. If running into two 16 Ohm cabs,

the amp should be set to 8 Ohms. If running into

two 8 Ohm cabs the amp should be set to 4 Ohms.

Note - The matching cabinet supplied with this

amp is wired for 16 Ohms.

Failure to comply with these points will result in

damage to the amplifier.

3. Output Selector

Matches amplifier output transformer impedance

to loudspeaker load impedance.

4. H.T. Fuse

See label for correct value.

5. Mains Input

Connects unit to power supply.

6. Mains fuse

See label for correct value.

JTM45 O/S Front and Rear Panel Features (continued)

JTM45 O/S Front Panel

10871 2 6543

JTM45 O/S Rear Panel

Whilst the information contained herein is correct at the time of publication; due to our constant improvement and development, Marshall

Amplification plc reserve the right to alter specifications without prior notice.

Marshall Amplification plc

Denbigh Road, Bletchley,

Milton Keynes, MK1 1DQ

England

Tel: (01908) 375411

Fax: (01908) 376118

Whilst the information contained herein is correct at the time of publication; due to our constant improvement and development, Marshall

Amplification plc reserve the right to alter specifications without prior notice.

BOOK-00057-00

Marshall Amplification plc

Denbigh Road, Bletchley,

Milton Keynes, MK1 1DQ

England

Tel: (01908) 375411

Fax: (01908) 376118

BOOK-00057-00

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Marshall Amplification Amplificateur

Marshall Amplification

Marshall Amplification SE 100 Manuel utilisateur

Marshall Amplification

Marshall Amplification ORIGIN 20 Manuel utilisateur

Marshall Amplification

Marshall Amplification STUDIO VINTAGE SV20H Manuel utilisateur

Marshall Amplification

Marshall Amplification DSL20CR Manuel utilisateur

Marshall Amplification

Marshall Amplification MG SERIES Manuel utilisateur

Marshall Amplification

Marshall Amplification MG15: MG15R Manuel utilisateur

Marshall Amplification

Marshall Amplification STUDIO JTM ST20H Manuel utilisateur

Marshall Amplification

Marshall Amplification Transistor Split Channel Manuel utilisateur

Marshall Amplification

Marshall Amplification AFD100 Slash Signature Series Manuel utilisateur

Marshall Amplification

Marshall Amplification 1959HW Manuel utilisateur

Marshall Amplification

Marshall Amplification 1974X Manuel utilisateur

Marshall Amplification

Marshall Amplification 2205 Manuel utilisateur

Marshall Amplification

Marshall Amplification Acoustic Soloist AS100D Manuel utilisateur

Marshall Amplification

Marshall Amplification MG SERIES Manuel utilisateur

Marshall Amplification

Marshall Amplification DSL100HR Manuel utilisateur

Marshall Amplification

Marshall Amplification Valvestate Pro Manuel utilisateur

Marshall Amplification

Marshall Amplification CODE 25 Manuel utilisateur

Marshall Amplification

Marshall Amplification MEGASTACK MG15FXMSDM Manuel utilisateur

Marshall Amplification

Marshall Amplification VDA-108-3GS Manuel utilisateur

Marshall Amplification

Marshall Amplification 2205 Manuel utilisateur

Marshall Amplification

Marshall Amplification 1923 Manuel utilisateur

Marshall Amplification

Marshall Amplification CODE Manuel utilisateur

Marshall Amplification

Marshall Amplification 1987 Manuel utilisateur

Marshall Amplification

Marshall Amplification VDA-104-3GS-2 Manuel utilisateur

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

NAD

NAD CI980 Manuel utilisateur

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

NAD

NAD T975 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Sony

Sony XM-S400D Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur