Maple Systems HMI5000 Series Manuel utilisateur

.Maple Systems Inc., 808 134th Street SW, Suite 120, Everett, WA 98204-7333 –www.maplesystems.com

1036-0175 Page 1 of 6 Rev. 01, 03/04/2011

C O N T R O L L E R I N F O R M A T I O N S H E E T

Maple Model(s)

PLC or Controller

HMI5000 Series

Allen-Bradley

PLC-5/xxE Series

(Ethernet)

Summary

Maple Systems’ HMI5000 Series Human/Machine Interface Terminals (Maple HMIs)

communicate with Allen Bradley PLC5e-series controllers using the DF1/PCCC protocol,

using the DF1 Typed Read and Typed Write commands. When configured with EZware-5000,

the Maple HMI is the master in a single master, multiple slave format. Please refer to the

HMI5000 Series Programming Manual for information on connecting multiple Maple HMIs to

a single PLC.

Compatible PLCs

PLC Family

PLC Model

PLC-5

PLC-5/20E, PLC-5/40E, PLC-5/80E;

1785-ENET/C Module

Communications

Cab

The Maple HMI should be connected to the ethernet port on the PLC or module. A list of

communications cables offered by Maple Systems as well as cable assembly instructions to

assist you in assembling your own communications cable are available on our website at

www.maplesystems.com.

WARNING If your communications cable is not wired exactly as shown in our cable

assembly instructions, damage to the HMI or loss of communications can

result.

Phone: 425/745-3229 • Fax: 425/745-3429 • Email: support@maplesystems.com • www.maplesystems.com

1036-0175 Page 2 of 6 Rev. 01, 03/04/2011

Accessible PLC Memory

emory

The following table lists the PLC’s register memory ranges that the Maple HMIs are able to

access. Please note that your PLC’s memory range may be smaller or larger than that

supported by these HMIs. The following register memory can be displayed in 16 or 32-bit

format on the Maple HMI. (Note: d=decimal)

PLC Register Type

Address Range

Format

PLC Register Description

0-999

ddd

Default Integer data file

0-999

ddd

Default Floating Point data file

Nfn

0-254254

fffnnn

File No. fff: 7, 9-254

Element No. nnn: 0-254

Any Integer Data File

Ffn

0-254254

fffnnn

File No. fff: 8, 9-254

Element No. nnn: 0-254

Any Floating Point Data File

T4PRE

0-999

ddd

Default Timer File

Preset Value

T4ACC

0-999

ddd

Default Timer File

Accumulated Value

C5PRE

0-999

ddd

Default Counter File

Preset Value

C5ACC

0-999

ddd

Default Counter File

Accumulated Value

TfnPRE

0-254254

fffnnn

File No. fff: 4, 9-254

Element No. nnn: 0-254

Any Timer File

Preset Value

TfnACC

0-254254

fffnnn

File No. fff: 4, 9-254

Element No. nnn: 0-254

Any Timer File

Accumulated Value

CfnPRE

0-254254

fffnnn

File No. fff: 5, 9-254

Element No. nnn: 0-254

Any Counter File

Preset Value

CfnACC

0-254254

fffnnn

File No. fff: 5, 9-254

Element No. nnn: 0-254

Any Counter File

Accumulated Value

0-999

ddd

Status File

.Maple Systems Inc., 808 134th Street SW, Suite 120, Everett, WA 98204-7333 –www.maplesystems.com

1036-0175 Page 3 of 6 Rev. 01, 03/04/2011

Discrete Memo

The following table lists the PLC’s discrete memory ranges that the Maple HMIs are able to

access. Please note that your PLC’s memory range may be smaller or larger than that

supported by these HMIs. The following discrete memory is displayable in single-bit format

on the Maple HMI. (Note: d=decimal)

PLC Bit Type

Address Range

Format

PLC Bit Description

000-99915

dddbb: bb = bit number

w/ leading zero

Default Bit File

N7Bit

000-99915

dddbb: bb = bit number

w/ leading zero

Bits Within Default Integer File

BfnBit

000-25425415

Fffnnnbb

File No. fff: 3, 9-254

Element No. nnn: 0-254

Bit No. bb: 00-15

Any Bit File

NfnBit

000-25425415

Fffnnnbb

File No. fff: 7, 9-254

Element No. nnn: 0-254

Bit No. bb: 00-15

Bits Within Any Integer File

T4Control

000-99915

dddbb: bb = bit number

w/ leading zero

Control Bits Within

Default Timer File

C5Control

000-99915

dddbb: bb = bit number

w/ leading zero

Control Bits Within

Default Counter File

TfnControl

000-25425415

Fffnnnbb

File No. fff: 4, 9-254

Element No. nnn: 0-254

Bit No. bb: 00-15

Control Bits Within

Any Timer File

CfnControl

000-25425415

Fffnnnbb

File No. fff: 5, 9-254

Element No. nnn: 0-254

Bit No. bb: 00-15

Control Bits Within

Any Counter File

000-99915

dddbb: bb = bit number

w/ leading zero

Bits Within Status File

Important Memory

Con

sideratio

If your PLC’s memory range is smaller than the range supported by the Maple HMIs, it is

possible to configure the HMI to monitor a PLC memory address which does not exist.

Since this can cause unpredictable results, when you configure the HMI please ensure that

all selected PLC memory addresses are valid for your PLC model.

Do not configure the HMI to write to any PLC memory address which should only be

written to by the PLC.

Phone: 425/745-3229 • Fax: 425/745-3429 • Email: support@maplesystems.com • www.maplesystems.com

1036-0175 Page 4 of 6 Rev. 01, 03/04/2011

EZwareSettings

The following table lists the communications settings that must be configured in

EZware. These settings can be found in the Edit-System Parameters menu under the

Device tab.

Please note:

The Recommended Settings column provides the recommended setting

based upon the default settings most commonly used in the Allen-

Bradley PLC-5e Series controller.

The Options column lists EZware’s options; your PLC may not support

every option.

Name

Recommended

Settings

Options

ImportantNotes

Name:

Allen Bradley

PLC5e

(EthernetIP-DF1)

HMIor PLC

PLC

Location

Local

Local,Remote

Selectlocal if PLC directly

connected to OIT, remote if

PLC connected thru another

HMI.

PLCtype:

Allen Bradley

PLC5e

(EthernetIP-DF1)

PLC I/F:

Ethernet

RS-232,

RS-485 2W,

RS-485 4W,

Ethernet

Mustmatch the controller

port setting.

PLCdefault station no.:

0-255

Must match the default

station no. assigned to the

PLC.

Use UDP

Unchecked

Checked or

Unchecked

Must be Unchecked

Settings: IP Address:

XXX.XXX.XXX.

XXX

0.0.0.0 –

255.255.255.255

Enter the IP Address of

the PLC.

Settings:Port

2222

None

This is the port address used

by the AB PLC5e.

Settings:Timeout

(sec)

1.0

0.1to 25.5

Adjustif longer timeout is

required.

.Maple Systems Inc., 808 134th Street SW, Suite 120, Everett, WA 98204-7333 –www.maplesystems.com

1036-0175 Page 5 of 6 Rev. 01, 03/04/2011

Name

Recommended

Settings

Options

ImportantNotes

Settings:Turn around

delay (ms):

0-1000

Timeout period between HMI

polls.

Settings: Send ACK

delay:

NotApplicable

Settings: Parameter 1:

NotApplicable

Settings: Parameter 2:

NotApplicable

Settings: Parameter 3:

Not Applicable

Interval of block pack

words

0-512

See HMI5000 Series

Programming Manual.

(Maple p/n 1010-1007)

Max. read-command

size (words):

Not Adjustable

Max. write-command

size (words):

Not Adjustable

Client ID

The HMI will identify itself to the PLC as MAPLE_HMI_nnn, where nnn is the last part of the

HMI’s IP address. For example, if the HMI has an IP address of 192.168.1.5, the HMI will

identify itself as MAPLE_HMI_005. If the project is run in the EasyBuilder Online Simulator,

the HMI identification will be MAPLE_HMI_OLS.

Communication Errors

Connection ID

When the HMI initially connects to the PLC5, the PLC5 provides a Connection ID

number that the HMI uses in all subsequent communications. If the PLC5 is unable

to provide a Connection ID, this value will be zero. The HMI stores this 32-bit value

in Local Words 8984 and 8985. To view the Connection ID, use a Numeric Display

object, addressed at LW8984, with the format set to 32-bit Unsigned.

Last Received Error Code

The HMI keeps the last DF1 Error Code in Local Word 8999. The High byte of

LW8999 is the DF1 STS error code, and will usually be hexadecimal F0. The low

byte of LW8999 is the DF1 EXT STS byte. If there are no errors, the value in

LW8999 will be 0.

Note: in the event that the PLC does not respond, the PLC No Response

window will be displayed, but the value in LW8999 will still be 0.

Phone: 425/745-3229 • Fax: 425/745-3429 • Email: support@maplesystems.com • www.maplesystems.com

1036-0175 Page 6 of 6 Rev. 01, 03/04/2011

Communication Errors are almost always caused by some type of mismatch between

the address specified in the HMI and the Data Table in the PLC. Common problems

are:

An object in the HMI is configured to read N7:250, but the N7 data file in the

PLC is configured only up to N7:200.

An object in the HMI is configured to read the preset of timer T10:0, but data

file 10 is defined in the PLC as something other than a Timer.

An object in the HMI is configured to read a Floating Point value, but the

specified data file is configured as something other than Floating Point. The

inverse of this is also true.

An object in the HMI is configured to read a bit, but the HMI object does not

properly specify leading zeros. For example

To read bit B3:5.7:

Device Type B3, address 57 (incorrect)

Device Type B3, address 507 (correct)

To read bit N12:35.3:

Device Type NfnBit, address 12353 (incorrect)

Device Type NfnBit, address 123503 (incorrect)

Device Type B3, address 1203503 (correct)

Communication Retries

When the HMI experiences a communication error, it will try to restart comms with

the PLC. This will always cause the HMI to obtain a new Connection ID from the

HMI. In some cases, it may be desirable to reduce the Inactivity Timeout setting in

the PLC so that the PLC will close any inactive connections sooner.

Table des matières

Autres manuels Maple Systems Terminal tactile

Maple Systems

Maple Systems HMC7030A-L Manuel utilisateur

Maple Systems

Maple Systems Silver Series Manuel utilisateur

Maple Systems

Maple Systems HMC7030A-M Manuel utilisateur

Maple Systems

Maple Systems HMI5040BN Manuel utilisateur

Maple Systems

Maple Systems HMI5000L Series Manuel utilisateur

Maple Systems

Maple Systems AEx-100 Series Manuel utilisateur

Maple Systems

Maple Systems HMI5070Bv3 Manuel utilisateur

Maple Systems

Maple Systems Blue Series Manuel utilisateur

Maple Systems

Maple Systems OIT 3160B Manuel utilisateur

Manuels Terminal tactile populaires d'autres marques

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manuel utilisateur

Ingenico

Ingenico AXIUM EX4000 Manuel utilisateur

Heisei Electronics

Heisei Electronics Q-POS 815 Manuel utilisateur

Amano

Amano MTX-15 Manuel utilisateur

FLOWBIRD

FLOWBIRD CWT Compact Touch Manuel utilisateur

Demco

Demco SP7 Manuel utilisateur

Lathem

Lathem PC600 Series Manuel utilisateur

Partner

Partner MF-2352 Manuel utilisateur

NCR

NCR RealPOS 7460-2 Manuel

Simrad

Simrad MS50 Instructions de montage

Unitech

Unitech MR350 MKII Guide de démarrage rapide

Jungheinrich

Jungheinrich WMT 210 Manuel utilisateur

Motorola

Motorola MTP850 Manuel utilisateur

YASKAWA

YASKAWA 62H-MDC0 Manuel utilisateur

MVG industries

MVG industries NeptuLink Manuel utilisateur

Price Industries Limited

Price Industries Limited FDC Manuel d'instructions

Honeywell

Honeywell TemaKey Manuel utilisateur

EBN

EBN BPC65-B-A16G Manuel utilisateur