Manitowoc ICE MACHINE K00385 Manuel utilisateur

K00385 ADAPTER KIT

Installation Instructions

The K00385 kit is used for installing S-1474 or S-1870 ice machines on a B-970 bin.

(Refer to Sheet 2 of 3 for pre-installation instructions.)

1. Note: Bin must be level before installation of ice machine.

A. Remove the foam tape from the front and sides of the bin where the stainless support/deflector will be located.

Use the support to reference the areas where the tape should be removed.

B. Place the support on the front edge of the bin and position as far forward as possible.

C. Locate the four pieces of the 2” long, 3/4” wide foam tape in the front corners, as shown.

D. Place the fillers on the bin, as shown. Make sure the two holes from the stainless support/deflector and fillers are

aligned on the side.

E. Using the fillers as templates, drill three 5/32” (4 mm.) holes, .500” (12.7 mm.) deep maximum, in the bin.

Warning: Do not drill through the interior liner. Attach each filler with three 10-24 x .500” screws provided.

F. Apply foam tape to the front and back of the bin between the fillers. Note: All other required foam tape comes

preassembled with the stainless support/deflector and fillers.

G. Note: It is recommended to RTV intersections and along the inside edge of the foam tape to prevent water

tracking.

2. Refer to ice machine installation manual for ice machine installation procedures.

Manitowoc Ice, Inc.

2110 South 26th Street, P.O. Box 1720, Manitowoc, WI 54221-1720 USA 000002544

Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-7879 Sheet 1 of 3

Web Site - www.manitowocice.com 06/13/07

Filler

.75” Wide Foam Tape

INSTALLER: It is

recommended to RTV

intersections and along inside

edge of foam tape to prevent

water tracking

Filler

#10-24 x .50”L

Screws Typ

Stainless Steel

Support/Deflector

.75” x 2.00”L Foam Tape

Typ both front corners

.75” Wide Foam Tape

Pre-installation Instructions for Removal of Existing Plastic Deflector

1. Remove the left and right side cover screws (see View A).

2. Remove the cover to expose the four screws that secure the plastic deflector (see Detail B).

3. Take out the four screws. Remove the plastic deflector, replace with a polymer spacer on each side and secure with

the four screws.

4. Reinstall the cover and proceed with the installation instructions.

000002544

Sheet 2 of 3

06/13/07

Plastic Deflector

Cover

Plastic Deflector

Screws

See Detail B

Detail B

View A

Cover Screw

Installing Ice deflector

1. Locate correct position for the deflector.

If the ice machine is installed, remove the water trough to obtain easier access.

The deflector must be located in the center of the drop zone.

Location is 11” from the left edge of the ice machine to the left edge of the mounting bracket.

2. Cut and remove the foam tape on the front and back of the bin where the deflector will be located.

3. Remove any residual adhesive; areas must be clean and dry.

4. Remove protective covering from the two sided tape on each deflector bracket.

5. Install the deflector bracket.

Distribute the mounting bracket equally on the front and back of the bin.

Locate the retaining pin to the back.

Press the mounting bracket into place.

6. Trim supplied foam tape to length of cuts from step 2 and apply over the top of the bracket. Seal edges

where deflector mounting bracket meets foam tape with silicone sealant to prevent water leakage.

7. Install the deflector into the mounting bracket.

Align tabs and slide the deflector toward the front of the bin.

Insert retaining pin into hole in the mounting bracket to lock deflector in place.

Reinstall water trough if removed in step 1.

000002544

Sheet 3 of 3

06/13/07

Water

Pump

Location

Water Trough

Located Behind

Splash Shield Splash

Shield

Ice Deflector

Autres manuels Manitowoc Machine à glaçons

Manitowoc

Manitowoc QM 20 Manuel utilisateur

Manitowoc

Manitowoc QC0700 Manuel utilisateur

Manitowoc

Manitowoc QM45A Manuel utilisateur

Manitowoc

Manitowoc Indigo Series Manuel utilisateur

Manitowoc

Manitowoc UG080A Manuel utilisateur

Manitowoc

Manitowoc J Series Manuel utilisateur

Manitowoc

Manitowoc SM Instructions d'utilisation

Manitowoc

Manitowoc EC Series Manuel d'instructions et de sécurité

Manitowoc

Manitowoc QM30A Manuel du propriétaire

Manitowoc

Manitowoc Q450 Manuel utilisateur

Manitowoc

Manitowoc CNF0201 Manuel utilisateur

Manitowoc

Manitowoc S model Manuel utilisateur

Manitowoc

Manitowoc QuietQube Series Manuel utilisateur

Manitowoc

Manitowoc CNF Series Manuel utilisateur

Manitowoc

Manitowoc Indigo I0300 Manuel utilisateur

Manitowoc

Manitowoc iAuCS Instructions d'utilisation

Manitowoc

Manitowoc S1000M Manuel utilisateur

Manitowoc

Manitowoc IB Series Guide de démarrage rapide

Manitowoc

Manitowoc CNF201 Instructions d'installation et d'utilisation

Manitowoc

Manitowoc RF2300 Mode d’emploi

Manitowoc

Manitowoc S1000M Manuel d'instructions et de sécurité

Manitowoc

Manitowoc Marine Q800 Mode d’emploi

Manitowoc

Manitowoc BG0260 Manuel utilisateur

Manitowoc

Manitowoc Indigo I1200 Manuel utilisateur

Manuels Machine à glaçons populaires d'autres marques

Hoshizaki

Hoshizaki KMD-460MWJ Manuel utilisateur

Sub-Zero

Sub-Zero 315I Instructions d'utilisation

Unold

Unold 48945 Manuel utilisateur

Kenmore

Kenmore 2217402A Manuel utilisateur

Cornelius

Cornelius WM600 Mode d'emploi

GE XPIO43SCSS Manuel utilisateur

Hoshizaki

Hoshizaki KMD-901MAH Manuel utilisateur

Whynter

Whynter FIM-450HA Manuel utilisateur

U-Line

U-Line UMCR014-SC01A Manuel d'installation

Andrew James

Andrew James AJ000522 Manuel utilisateur

Scotsman

Scotsman CME1356 Manuel utilisateur

Scotsman

Scotsman ACM 25 Manuel utilisateur

Kärcher

Kärcher IP 120 Manuel utilisateur

U-Line

U-Line SS1095 Manuel utilisateur

Maytag

Maytag MIM1554WRS - Ice Maker Manuel utilisateur

Hoshizaki

Hoshizaki KM-630MAH Manuel utilisateur

Princess

Princess Yonanas Manuel utilisateur

Unold

Unold 48946 Manuel utilisateur