Manitowoc G-0600 Manuel utilisateur

J/B/G-0600 COMPRESSOR REPLACEMENT

Installation Instructions

NOTE: THIS REPLACEMENT IS ONLY FOR THE J, B, AND G-SERIES ICE MACHINES. START AND RUN

COMPONENT CHANGES VARY WITH THE TYPE OF MACHINE. FOR J-SERIES MACHINES ONLY, THE

RUN CAPACITOR NEEDS TO BE REPLACED WITH THE ONE INCLUDED IN THE KIT. B AND G-SERIES

MACHINES NEED ALL OF THE START AND RUN COMPONENTS REPLACED WITH THE ONES

INCLUDED IN THE KIT.

1. Disconnect power to the ice machine at the electrical

disconnect (moving the toggle switch to the off

position will not disconnect line voltage).

2. Remove panels (top, front, left and right sides).

3. Recover refrigerant from ice machine.

4. Remove right side corner post (when facing the front

of the machine) and back panel.

5. Remove wiring from compressor terminals.

6. Unsweat suction line at compressor port. Unsweat

discharge and process lines at the T fitting and

swage joint (or after “T” fitting, if remote)

respectively.

NOTE: IF REPLACING COMPRESSOR IN A

REMOTE ICE MACHINE, BE SURE TO

UNSWEAT THE CONNECTION BETWEEN

THE HPR VALVE AND THE PROCESS

TUBING AT THE “T” FITTING.

7. Remove compressor from machine. Make sure to

crimp and braze shut ports to compressor.

8. Insert new compressor into the machine, as shown.

Manitowoc Ice, Inc.

2110 South 26 Street, P.O. Box 1720, Manitowoc, WI 54221-1720 USA 8006183

Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-7879 Sheet 1 of 3

Web Site - www.manitowocice.com 06/25/01

“T” Fitting

Swage Joint

9. Fit tubing provided into the proper place, as shown.

Cut ice machine suction line to fit new tubing.

Deburr suction line before fitting new tubing in.

NOTE: IF REPLACING COMPRESSOR INTO A

REMOTE ICE MACHINE, MAKE SURE TO

FIRST FOLLOW INSTRUCTIONS A, B, AND C

BELOW, BEFORE PROCEEDING TO

INSTRUCTION #10.

A. Replace elbow with “T” fitting.

B. Replace HPR valve and L-shaped tube that was

removed earlier. Adjust to fit without rubbing

against any other parts of the machine.

C. Return to instruction #10.

10. Place armaflex insulation provided in kit on suction

line, as shown in picture below. Slide insulation up

tubing and secure while brazing.

11. Braze all tubing into place. Purge system with

nitrogen during all brazing operations on the ice

machine.

12. Use electrical tape to seal suction line insulation.

13. Reattach the wiring harness to the compressor.

14. Replace the filter/dryer before evacuating the

machine. Make sure that the filter/dryer tubing is

not rubbing against the compressor.

15. Evacuate machine to 500 microns.

8006183

Sheet 2 of 3

06/25/01

16. Charge the machine with the nameplate charge.

17. Make sure that all the tubing is not rubbing against

anything else in the machine.

18. Reinstall the corner post that was removed earlier

and place electrical cover on compressor.

19. Reinstall back panels of ice machine.

20. Make sure to replace start and run components

according to the machine you are replacing the

compressor in. See note in the beginning of

instructions for designation.

21. Reinstall all other panels.

22. Reconnect power and test run ice machine.

8006183

Sheet 3 of 3

06/25/01

Ce manuel convient aux modèles suivants

Autres manuels Manitowoc Machine à glaçons

Manitowoc

Manitowoc QM20 Series Manuel du propriétaire

Manitowoc

Manitowoc QR0670C Manuel utilisateur

Manitowoc

Manitowoc EC Serie Manuel d'instructions et de sécurité

Manitowoc

Manitowoc K00523 Manuel utilisateur

Manitowoc

Manitowoc 30" Q-MODEL ICE MACHINES MYLAR STRIP 7600153 Manuel utilisateur

Manitowoc

Manitowoc QC0700 Manuel utilisateur

Manitowoc

Manitowoc WELTBILT NEO 310 Manuel utilisateur

Manitowoc

Manitowoc GR1200A Manuel utilisateur

Manitowoc

Manitowoc Indigo Guide de démarrage rapide

Manitowoc

Manitowoc CNF201 Instructions d'installation et d'utilisation

Manitowoc

Manitowoc ICE DEFLECTOR K00382 Manuel utilisateur

Manitowoc

Manitowoc MII 402 Manuel utilisateur

Manitowoc

Manitowoc UG080A Manuel utilisateur

Manitowoc

Manitowoc 1100 series Manuel utilisateur

Manitowoc

Manitowoc G-1700 Manuel utilisateur

Manitowoc

Manitowoc B Series Manuel utilisateur

Manitowoc

Manitowoc QM20 Series Manuel utilisateur

Manitowoc

Manitowoc Indigo NXT Manuel utilisateur

Manitowoc

Manitowoc QD0322A Manuel utilisateur

Manitowoc

Manitowoc Marine Q800 Mode d’emploi

Manitowoc

Manitowoc QuietQube Series Manuel utilisateur

Manitowoc

Manitowoc HR-0200A Manuel utilisateur

Manitowoc

Manitowoc IT1900 Manuel utilisateur

Manitowoc

Manitowoc Q Manuel utilisateur

Manuels Machine à glaçons populaires d'autres marques

Hoshizaki

Hoshizaki KMD-460MWJ Manuel utilisateur

Sub-Zero

Sub-Zero 315I Instructions d'utilisation

Unold

Unold 48945 Manuel utilisateur

Kenmore

Kenmore 2217402A Manuel utilisateur

Cornelius

Cornelius WM600 Mode d'emploi

GE XPIO43SCSS Manuel utilisateur

Hoshizaki

Hoshizaki KMD-901MAH Manuel utilisateur

Whynter

Whynter FIM-450HA Manuel utilisateur

U-Line

U-Line UMCR014-SC01A Manuel d'installation

Andrew James

Andrew James AJ000522 Manuel utilisateur

Scotsman

Scotsman CME1356 Manuel utilisateur

Scotsman

Scotsman ACM 25 Manuel utilisateur

Kärcher

Kärcher IP 120 Manuel utilisateur

U-Line

U-Line SS1095 Manuel utilisateur

Maytag

Maytag MIM1554WRS - Ice Maker Manuel utilisateur

Hoshizaki

Hoshizaki KM-630MAH Manuel utilisateur

Princess

Princess Yonanas Manuel utilisateur

Unold

Unold 48946 Manuel utilisateur