Manitowoc I1406 Series Instructions d'utilisation et de sécurité

Manitowoc Ice

2110 South 26th Street, P.O. Box 1720, Manitowoc, WI 54221-1720 USA 000013291

Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-7879 Page 1 of 2

Web Site - www.manitowocice.com Rev 00

COMPRESSOR REPLACEMENT

I1406 SERIES

1. Disconnect the power to the ice machine at the electrical 6. Unbraze the suction line at the compressor port. Unbraze

panel. (pushing the power button to the off position the discharge port at the compressor.

will not disconnect line voltage). Unbraze the bottom joint at the compressor discharge port.

2. Remove all the panels (top, front left, and right sides). Cut the tubing when replacing filter drier.

3. Recover all refrigerant from the ice machine. Do not unbraze the filter drier.

4. Remove the right rear back panel and top rail.

Note:

(Orientation is done while facing the front of the ice machine)

Note: When replacing the compressor in a Remote

Ice Machine; be sure to unbraze the suction

and process port at the compressor, replace

the filter drier. Cut tubing to replace the

filter dryer. Do not unbraze filter drier.

Remember that there are four points of

recovery on a remote.

5. Remove the wiring or plug from the compressor terminals.

7. Remove the compressor from the ice machine. Make

sure compressor ports are crimped and brazed shut.

Unbraze

I1406

Compressor

plug location

I1406

Compressor

position

Filter Drier

Cut the tubing

4 Recovery

Points

Manitowoc Ice

2110 South 26th Street, P.O. Box 1720, Manitowoc, WI 54221-1720 USA 000013291

Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-7879 Page 2 of 2

Web Site - www.manitowocice.com Rev 00

COMPRESSOR REPLACEMENT

I1406 SERIES

9. Insert the NEW compressor into the Ice Machine, and

Position the compressor as shown.

11. Purge the system with nitrogen before and during

all brazing operations.

I1406 Air, Water, & Remote Ice Machines

12. Position the tubes back into compressor.

13. Replace the filter drier before evacuating the refrigeration

system of the ice machine.

Secure in place while brazing the joints

10. Reinsert the old tubing into the new compressor ports. Braze all tubing into place.

Insert 1/2 OD discharge tube into the discharge port of 14. Evacuate to 500 microns minimum.

the compressor. Insert 5/8 OD suction tube and bushing Insure that all the tubing is not rubbing against

supplied with the kit, (if required) port of the compressor. anything in the ice machine.

Braze tubes into the compressor ports. Insure that the thermistor and clip are replaced back onto

the 1/2 OD discharge tube and the new thermistor boot

Adjust the tubing to fit without rubbing supplied in the kit.

any other tubing or parts of the ice machine. 15. Reinstall the corner post and then the top rail.

16. Be sure to replace the run capacitor supplied with

compressor kit.

17. Weigh in correct refrigerant charge from the nameplate

found on the ice machine.

18. Reconnect the compressor with the wiring harness.

19. Reinstall all the other remaining outer panels.

20. Reconnect the power and turn on power switch.

Test and run the ice machine.

Suction tube

position.

New

Compressor

Discharge tube

connection position

Suction

Tube

Discharge

Tube

Thermistor boot

Autres manuels Manitowoc Machine à glaçons

Manitowoc

Manitowoc QM30A Manuel du propriétaire

Manitowoc

Manitowoc QF0400 Manuel utilisateur

Manitowoc

Manitowoc P Series Manuel du propriétaire

Manitowoc

Manitowoc Q 1800 Mode d’emploi

Manitowoc

Manitowoc B150 Manuel utilisateur

Manitowoc

Manitowoc Indigo I1200 Manuel utilisateur

Manitowoc

Manitowoc BG0260 Manuel utilisateur

Manitowoc

Manitowoc NEO UD0140A Instructions d'installation et d'utilisation

Manitowoc

Manitowoc QM20 Series Manuel du propriétaire

Manitowoc

Manitowoc Indigo Guide de démarrage rapide

Manitowoc

Manitowoc UG Series Manuel utilisateur

Manitowoc

Manitowoc SM050 Manuel utilisateur

Manitowoc

Manitowoc CORNELIUS ENDURO K00342 Manuel utilisateur

Manitowoc

Manitowoc 1100 series Manuel utilisateur

Manitowoc

Manitowoc ICE DEFLECTOR K00382 Manuel utilisateur

Manitowoc

Manitowoc QM45A Manuel utilisateur

Manitowoc

Manitowoc S model Manuel utilisateur

Manitowoc

Manitowoc S3000 Manuel utilisateur

Manitowoc

Manitowoc S600M Manuel d'instructions et de sécurité

Manitowoc

Manitowoc J250 Manuel utilisateur

Manitowoc

Manitowoc Indigo Series Instructions d'utilisation

Manitowoc

Manitowoc Indigo Series Manuel utilisateur

Manitowoc

Manitowoc WELTBILT NEO 310 Manuel utilisateur

Manitowoc

Manitowoc SN20 Instructions d'utilisation

Manuels Machine à glaçons populaires d'autres marques

Hoshizaki

Hoshizaki KMD-460MWJ Manuel utilisateur

Sub-Zero

Sub-Zero 315I Instructions d'utilisation

Unold

Unold 48945 Manuel utilisateur

Kenmore

Kenmore 2217402A Manuel utilisateur

Cornelius

Cornelius WM600 Mode d'emploi

GE XPIO43SCSS Manuel utilisateur

Hoshizaki

Hoshizaki KMD-901MAH Manuel utilisateur

Whynter

Whynter FIM-450HA Manuel utilisateur

U-Line

U-Line UMCR014-SC01A Manuel d'installation

Andrew James

Andrew James AJ000522 Manuel utilisateur

Scotsman

Scotsman CME1356 Manuel utilisateur

Scotsman

Scotsman ACM 25 Manuel utilisateur

Kärcher

Kärcher IP 120 Manuel utilisateur

U-Line

U-Line SS1095 Manuel utilisateur

Maytag

Maytag MIM1554WRS - Ice Maker Manuel utilisateur

Hoshizaki

Hoshizaki KM-630MAH Manuel utilisateur

Princess

Princess Yonanas Manuel utilisateur

Unold

Unold 48946 Manuel utilisateur