Manitowoc ECS018A Manuel utilisateur
1-1
Installation Instructions
Section 1
General Information
It is recommended that this ice machine be inspected and
installed by a qualified service technician.
WARNING
If you do not understand the procedures or the safety
precautions that must be followed, call your local service
representative to perform the necessary installation
procedures for you.
Follow all recommendations and instructions for proper
installation and safe operation of this ice machine.
WARNING
PERSONAL INJURY POTENTIAL
Do not operate equipment that has been misused, abused,
neglected, damaged, or altered/modified from that of original
manufactured specifications.
Model Numbers
This manual covers the following models:
Self-Contained
Air-Cooled Self-Contained
Water-Cooled
ECS018A Not Available
ECG018A Not Available
ECS020A Not Available
ECG020A Not Available
ECS030A Not Available
ECG030A Not Available
ECS040A ECS040W
ECG040A ECG040W
ECS050A ECS050W
ECG050A ECG050W
ECS065A ECS065W
ECG065A ECG065W
ECS080A ECS080W
ECG080A ECG080W
Model Numbers Identification
EC S 040 A
Ice Cube Size
S – Standard Cube
G – Large Cube
Ice Machine Series Condenser Type
A – Air Cooled
W – Water Cooled
Ice Machine Model
1-2
Installation Instructions Section 1
Location of Ice Machine
The location selected for the ice machine must meet the
following criteria. If any of these criteria are not met, select
another location.
•The location must be indoors.
•The location must be free of airborne and other
contaminants.
•The air temperature must be at least 10°C (50°F), but must
not exceed 43°C (110°F).
•The location must not be near heat-generating equipment or
in direct sunlight.
•The location must be capable of supporting the weight of the
ice machine and a full bin of ice.
•The location must allow enough clearance for water, drain
and electrical connections in the rear of the ice machine.
•The location must not obstruct airflow through or around the
ice machine (condenser airflow is in and out the front). Refer
to the chart below for clearance recommendations.
Self-Contained
Air-Cooled Self-Contained
Water-Cooled
Top/Sides 203 mm (8 in.)* 127 mm (5 in.)*
Back 127 mm (5 in.)* 127 mm (5 in.)*
* NOTE: The ice machine may be built into a cabinet.
There is no minimum clearance requirement for the top or left
and right sides of the ice machine. The listed values are
recommended for efficient operation and servicing only.
CAUTION
The ice machine must be protected if it will be subjected to
temperatures below 0°C (32°F). Failure caused by exposure to
freezing temperatures is not covered by the warranty.
Leveling the Ice Machine
Levelers are included with all ice machine. Legs are an available
option.
1. Screw the legs or levelers into the bottom of the ice
machine.
2. Screw the foot of each leg or leveler in as far as possible.
Move the ice machine into its final position.
3. Level the ice machine correctly. Use a level on top of the ice
machine. Turn each foot as necessary to level the ice
machine from front to back and side to side.
Checking Ice Machine Level
THREAD
LEVELING LEG
INTO BASE OF
CABINET
1-3
Installation Instructions
Section 1
Electrical Service
GENERAL
WARNING
All wiring must conform to local, state and national codes.
VOLTAGE
The maximum allowable voltage variation is ±6% of the rated
voltage on the ice machine model/serial number plate at start-up
(when the electrical load is highest).
All ice machines are factory pre-wired with a 2 meter (6 ft)
power cord, no plug is supplied.
WARNING
The ice machine must be grounded in accordance with
national and local electrical codes.
FUSE/CIRCUIT BREAKER
A separate fuse/circuit breaker must be provided for each ice
machine. An electrical disconnect switch must be provided if the
ice machine is hard wired (wired without a plug).
TOTAL CIRCUIT AMPACITY
The total circuit ampacity is used to help select the wire size of
the electrical supply.
The wire size (or gauge) is also dependent upon location,
materials used, length of run, etc., This must be determined by a
qualified electrician.
Air-Cooled Water Cooled
Ice Machine
Maximum
Fuse/Circuit
Breaker
Total Amps
KW
Maximum
Fuse/Circuit
Breaker
Total Amps
KW
230/1/50 10 Amp 2.2 .506 N/A N/A N/A
EC018 &
EC020
(without a
Timer) 230/1/60 10 Amp 2.2 .506 N/A N/A N/A
230/1/50 10 Amp 2.5 .575 10 Amp 2.3 .529
EC020
(with a Timer) 230/1/60 10 Amp 2.5 .575 10 Amp 2.3 .529
230/1/50 10 Amp 2.5 .575 10 Amp 2.3 .529
EC030
After Serial
Number - 230/1/60 10 Amp 2.5 .575 10 Amp 2.3 .529
230/1/50 10 Amp 3.4 .782 10 Amp 3.2 .736
EC030
Before Serial
Number - 230/1/60 10 Amp 3.4 .782 10 Amp 3.2 .736
230/1/50 10 Amp 3.4 .782 10 Amp 3.1 .713
EC040 230/1/60 10 Amp 3.4 .782 10 Amp 3.1 .713
230/1/50 10 Amp 4.0 .92 10 Amp 3.7 .851
EC050 230/1/60 10 Amp 4.0 .92 10 Amp 3.7 .851
230/1/50 10 Amp 4.2 .99 10 Amp 3.8 .874
EC065 230/1/60 10 Amp 4.2 .99 10 Amp 3.8 .874
230/1/50 10 Amp 4.4 1.45 10 Amp 4.0 .92
EC080 230/1/60 10 Amp 4.4 1.45 10 Amp 4.0 .92
1-4
Installation Instructions Section 1
Water Service/Drains
WATER SUPPLY
Local water conditions may require treatment of the water to
inhibit scale formation, filter sediment, remove chlorine, and
improve taste and clarity.
WATER INLET LINES
Follow these guidelines to install water inlet lines:
•Do not connect the ice machine to a hot water supply. Be
sure all hot water restrictors installed for other equipment are
working. (Check valves on sink faucets, dishwashers, etc.)
•Water pressure to the machine should be between 1.4 to 5.5
bar (20 to 80 psi).
•If water pressure exceeds the maximum 5 bar recommended
pressure, obtain a water pressure regulator from your
Manitowoc distributor. Adjust pressure to 2.5 bar (37 psi).
•Install a water shut-off valve.
•Connect to a potable water supply only.
Important
If you are installing a water filter system, make sure that
you use a separate line for water-cooled condenser.
Filter life will be greatly reduced if filtered water is used
for water-cooled condenser.
DRAIN CONNECTIONS
Follow these guidelines when installing drain lines to prevent
drain water from flowing back into the ice machine and storage
bin:
•Drain lines must have a 3.8 cm (1.5 inch) drop of run for
each meter (3 feet), and must not create traps.
•The floor drain must be large enough to accommodate
drainage from all drains.
•Run separate bin and water-cooled condenser drain lines.
Insulate them to prevent condensation.
WATER SUPPLY AND DRAIN LINE SIZING/CONNECTIONS
Water Temperature
Water
Pressure Ice Machine
Fitting Tubing Size Up to Ice
Machine Fitting
*Ice Making
Water Inlet 10ºC (50ºF) Min.
40ºC (104ºF) Max. 1.4 Bar (20 Psi) Min.
5.5 Bar (80 Psi) Max 3/4” Male Pipe
Thread 15mm (1/2”) Inside
Diameter Minimum
**Drain Connection
Outlet ----- ----- 7/8” Barb connection 18mm (3/4”) Minimum
Inside Diameter
Condenser Water Inlet 0.6ºC (33ºF) Min.
32.2ºC (90ºF) Max. 1.4 Bar (20 Psi) Min.
10.3 Bar (150 Psi) Max 3/8” Female pipe
Thread 15mm (1/2”) Inside
Diameter Minimum
Condenser Water Outlet ----- ----- 1/2” Female pipe
Thread 15mm (1/2”) Minimum
Inside Diameter
* Water inlet hose supplied with machine.
3/4” Female Pipe Thread/ 2 meters long.
** Drain hose supplied with machine.
7/8” (22.2mm) hose/ 2 meters long.
ELECTRICAL
DRAIN
POTABLE WATER
INLET
WATER COOLED
CONDENSER INLET
WATER COOLED
CONDENSER OUTLET
1-5
Installation Instructions
Section 1
Dimensions
Condenser Water
Inlet Condenser Water
Outlet Potable Water Inlet Drain Electrical
MODEL H W D 1 6 2 7 4 9 5 10 3 8
MM 635 343 420 NA NA NA NA 63.5 88.9 50.8 140 76.2 38.1
EC018 INCH 25.0 13.5 16.5 NA NA NA NA 2.5 3.5 2.0 5.5 3.0 1.5
MM 650 450 475 100.5 53.4 45.5 138.4 125.5 118.4 45.3 225 125.5 183.4
EC020
&
EC030 INCH 25.59 17.72 18.7 3.96 2.1 1.79 5.45 4.94 4.66 1.78 8.86 4.94 7.22
MM 800 550 550 108 77.5 68 123 87.5 221 68 275 108 168
EC040
&
EC050 INCH 31.5 21.65 21.65 4.25 3.05 2.68 4.82 3.44 8.71 2.68 10.83 4.25 6.59
MM 902 700 600 114.3 82.6 76.2 120.7 95.25 222.25 82.6 279.4 120.7 171.5
EC065
&
EC080 INCH 35.5 27.5 23.5 4.5 3.25 3.0 4.75 3.75 8.75 3.25 11.0 4.75 6.75
D
W
H
1
245
3
6
78
9
10
152.4 mm
(
6 in
)
ELECTRICAL
DRAIN
POTABLE WATER
INLET
WATER COOLED
CONDENSER INLET
WATER COOLED
CONDENSER OUTLET
1-6
Installation Instructions Section 1
Installation Checklist
Is the ice machine level?
Has all of the internal packing been removed?
Have all of the electrical and water connections been
made?
Has the supply voltage been tested and checked against
the rating on the nameplate?
Are all components installed as shown in Section 3?
Water spray bar, ice chute, water curtain and sump
drain overflow tube are all in place?
Has the ice machine been installed where ambient
temperatures will remain in the range of 10°- 43°C
(50°- 110°F)?
Has the ice machine been installed where the incoming
water temperature will remain in the range of 10°-
32.2°C (50°- 90°F)?
Is there a separate drain line for the water-cooled
condenser?
Are all electrical leads free from contact with
refrigeration lines and moving equipment?
Has the owner/operator been instructed regarding
maintenance and the use of Manitowoc Cleaner and
Sanitizer?
Has the owner/operator completed the warranty
registration card?
Has the ice machine and bin been sanitized?
Has this manual been given to the owner/operator?
Is the ice -off - wash switch set to the ice position?
Before Starting the Ice Machine
All ice machines are factory-operated and adjusted before
shipment. Normally, new installations do not require any
adjustment.
To ensure proper operation, follow the Operational Checks in
section 3 of this manual. Starting the ice machine and completing
the Operational Checks are the responsibilities of the
owner/operator.
Adjustments and maintenance
procedures outlined in this manual
are not covered by the warranty.
WARNING
PERSONAL INJURY POTENTIAL
Do not operate equipment that has been misused, abused,
neglected, damaged, or altered/modified from that of original
manufactured specifications.
Ce manuel convient aux modèles suivants
13
Table des matières
Autres manuels Manitowoc Machine à glaçons
Manitowoc
Manitowoc Indigo I0300 Manuel utilisateur
Manitowoc
Manitowoc KEY CARD KIT K00152 Manuel utilisateur
Manitowoc
Manitowoc WELTBILT NEO 310 Manuel utilisateur
Manitowoc
Manitowoc CNF201 Instructions d'installation et d'utilisation
Manitowoc
Manitowoc S model Instructions d'utilisation
Manitowoc
Manitowoc RFF Manuel utilisateur
Manitowoc
Manitowoc I1406 Series Instructions d'utilisation et de sécurité
Manitowoc
Manitowoc ICE MACHINE K00385 Manuel utilisateur
Manitowoc
Manitowoc QC0700 Instructions d'utilisation
Manitowoc
Manitowoc MARINE MODEL S1800 Manuel utilisateur
Manitowoc
Manitowoc Q450 Manuel utilisateur
Manitowoc
Manitowoc Q130 series Instructions d'utilisation
Manitowoc
Manitowoc SN20 Instructions d'utilisation
Manitowoc
Manitowoc EC Series Manuel d'instructions et de sécurité
Manitowoc
Manitowoc QM20 Series Manuel utilisateur
Manitowoc
Manitowoc Q130 series Instructions d'utilisation
Manitowoc
Manitowoc MAC 6 K058 Manuel utilisateur
Manitowoc
Manitowoc QuietQube Indigo Series Manuel utilisateur
Manitowoc
Manitowoc SD0302A Manuel utilisateur
Manitowoc
Manitowoc ENDURO 300 KH0180 Manuel utilisateur
